If the key goes all the way in and turns smoothly, but the bike lock still won’t open, then corrosion has probably fused the two parts of the lock together. Spray WD-40 liberally into joints where the shackle meets the bar In this case, try spraying loads of WD-40 into the joint.
How to reset an OnGuard lock?
How to Reset an Onguard Lock. 1 Step 1. Arrange the dials to your current or pre-set four-digit combination. Check that that the numbers are aligned with the guide points beside the ... 2 Step 2. 3 Step 3. 4 Step 4. 5 Step 5. More items
What makes OnGuard locks so safe?
On the inside, OnGuard locks earn the highest safety ratings with double and quad-locking mechanisms, bump-resistant cylinders, and hardened steel shackles and chains.
How do I open the OnGuard lock shackle?
Arrange the dials to your current or pre-set four-digit combination. Check that that the numbers are aligned with the guide points beside the dials. Press the "Open" button and pull the Onguard lock shackle to the open position.
Why won't my bike lock open?
But if the key slides in easily and turns freely but the bike lock still won’t open, then the problem is probably where the two parts of the lock join. A jammed key hole can be caused by dirt and debris, frozen water, rust or simply misaligned discs.
How do you unlock a onguard bike lock?
0:011:00OnGuard Lock Combination Tutorial - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe dial back counterclockwise. Until it comes to a full stop. Your. Number is still the number youMoreThe dial back counterclockwise. Until it comes to a full stop. Your. Number is still the number you just set at zero zero zero. Four and you are able to now insert the key all the way.
How do you force a bike lock to open?
0:262:12How To Unlock Cable Bike Lock Without Combination - YouTubeYouTubeStart of suggested clipEnd of suggested clipOne thing I've already done it's already sprayed the dials down with wd-40. So that they're movingMoreOne thing I've already done it's already sprayed the dials down with wd-40. So that they're moving nice and smoothly they were a little bit stiff to begin with and how they move smoothly.
How do you open a stuck U lock?
2:513:51How To Fix A Jammed Kryptonite U Lock - YouTubeYouTubeStart of suggested clipEnd of suggested clipAs you can see it is rust put some wd-40 in there as well it also be the locking mechanism as rust.MoreAs you can see it is rust put some wd-40 in there as well it also be the locking mechanism as rust. And it's preventing it from moving. So you should put some wd-40.
How do you break a 4 digit bike lock?
1:193:39Cracking a combination lock - YouTubeYouTubeStart of suggested clipEnd of suggested clipAll you have to do is pull on the two ends. Not even very hard just to put some pressure in theMoreAll you have to do is pull on the two ends. Not even very hard just to put some pressure in the chamber. And then starting with the number wheel at the open. End just go through one by one.
How do you fix a stuck bike lock?
So the first job is to loosen them with some WD-40! Hold the lock so the key hole is facing the floor and squirt WD-40 into the hole. This should dislodge any street gunk and allow it to drain out of the locking mechanism. Then turn the bike lock around so the hole is facing the upwards and insert the key.
What is a good bike lock?
A good quality bike lock will also feature a key cover. Key covers slide over the locking mechanism to prevent debris from entering the keyhole. This will keep your lock functioning properly and prevent it from jamming. The best bike locks will come with good quality keys.
How to flush out dirt from bike?
Position the bike lock so that the keyhole is facing downwards, then using the application straw, apply several short sharp bursts . Continue repeating this until the liquid streams out. Whilst doing this, you can insert the key in between squirts and twist it to encourage the dirt to flush out.
What happens if your bike lock is left out?
If your bike lock has been left out in the elements or is old, it could be badly corroded together inside. This time you’ll be allowed to get some payback on your lock! If after attempting the above steps your lock is still jammed, it’s worth using a hammer to strike the locks shackle.
How to get a lock to loosen when it won't turn?
If you can fully insert the key into the mechanism but it won’t fully turn or it won’t turn at all, then more WD-40 is needed. Apply a few squirts into the locking mechanism and gently wriggle the key around inside. This will encourage the lock to loosen.
Why is my bike lock jammed?
A build up of rust, dirt and debris could be the reason your bike lock has jammed. If you’ve left your bike locked up for a long time, the elements can take their toll on your lock and cause it to seize up in a number of different ways.
What happens if you can't insert a key into a lock?
If you are still unable to insert the key into the lock properly, then the cylinders may be out of line. Attempt to insert your key into the locking mechanism, twisting gently from side to side, this will normally re-align the cylinders.
Why do I need a bright LED key for my bike?
A bright LED key will save you from fumbling around in the darkness whilst unlocking your bike. If your lock is jammed the LED can be used to determine the cause of the jam. As covered above, as long as you understand bike lock maintenance (see step 2), you’re unlikely to have any issues. Preview. Model.
What is an Onguard lock?
A proper lock can guard against theft and serve as a visual deterrent for would-be thieves. Onguard combination locks allow you to set your own combination. This feature offers you the advantage of selecting a personal combination, and changing that combination as many times as needed or desired. Advertisement.
How to lock a bicycle?
Always lock your bicycle through the frame and the front wheel. If possible, remove the front wheel and place it beside the rear wheel. Then, pass the lock through both wheels as well as the frame.
How long has John Y. been writing?
He has been writing for over 10 years and his work has appeared on various online publications. A collection of his short stories was published in spring 2010. He is a graduate of Appalachian State University. eHow may earn compensation through affiliate links in this story.
How to fix a bike lock that is jammed?
Summary of how to fix a jammed bike lock! 1. Work out which part of the bike lock is jammed. Bike locks tend to jam in two places: in the key hole so you can’t turn the key. in the body so you can’t separate the two parts of the lock. Bike locks tend to jam in 2 places.
Why does my bike lock jam?
All bike locks will jam if you try to turn the key before it’s been fully inserted into the keyhole. As I've mentioned above, most bike lock mechanisms contain a series of discs and all of them need to be fully rotated before the lock will open.
How to lock and unlock a bike lock?
To lock and unlock the bike lock, all of the discs need to be turned in the same direction at the same time. Have a look into the key hole of your bike lock and you should be able to see what I'm talking about! If the these discs get misaligned, the bike lock can't be locked or unlocked.
What happens if the key doesn't go into the key hole?
If the key doesn't go all the way into the key hole, it won't be able to turn all the discs and you won't be able to lock (or unlock) the bike lock! The problems start when the holes in the bottom discs fall out of alignment with the holes in the upper discs, as this will prevent the key from being fully inserted.
Why won't my bike lock open?
A jammed key hole can be caused by dirt and debris, frozen water, rust or simply misaligned discs.
Can Abus locks jam?
Abus locks. Likewise, Abus are not particularly helpful when it comes to their bike locks jamming. However, Abus locks are so well made, that they tend to suffer from fewer problems in the first place. For instance, in my experience, it's much more difficult to accidently misalign the discs in an Abus lock!
What to do if your key is stuck in the hole?
If your key has got stuck in the key hole and you can't get it out, then the solution is the same as above: plenty of WD-40 in between gently trying to turn the key back and forth.