Specifications
| Internal diameter | 2” to 14” |
| Bore type | full flow, rough bore |
| Liner type | H2S resistant HNBR |
| Design pressure | up to 7,500 psi |
| Operating temperature | -30° C to +90° C (-22° F to 194° F) |
Full Answer
What is the best natural gas heater?
Top 10 Best Gas Water Heater Reviews 2021
- Rinnai RUC98iN Ultra Series – Best Gas Tankless Water Heater. One of the top tankless gas water heaters today is the Rinnai RUC98iN from the brand’s Ultra series.
- Rheem RTGH-95DVLN 9.5 GPM Indoor Direct Vent – Best Natural Gas Tankless Water Heater. ...
- Eccotemp i12-NG Tankless Indoor Heater, 1/2-inch Fittings – Energy Efficient Water Heater. ...
Are natural gas pipelines safe?
DALLAS, Texas (KTVT) — A major pipeline company is threatening to cutoff natural gas to five power plants in Texas, a move that could have a major impact on the state power grid. Several ...
What size orifice does a natural gas dry use?
You'll find that a 75-drill orifice supplies about 1,400 BTUs per hour with natural gas as the fuel and about 3,000 BTUs per hour with propane. That's a significant difference, and it's due to the different pressures at which the gases are supplied. Cooktop burners typically supply about 40,000 BTUs per hour.
Do natural gas water heaters use electricity?
Most gas water heaters do not use electricity to operate. However, many of them rely on a minimal amount of electricity to get their pilot light burning in order to light their igniter. So although the gas heater doesn’t need electricity to run, it does need a minimal amount of electricity to start it.
What kind of hose can be used for natural gas?
What Kind Of Hose Can I Use For Natural Gas? It should be noted that brass, brass steel type 304/316, and metal like zinc, are the standard materials used for the fitting of the ular brass, type 304/316 stainless steel or zinc plated steel are used as the material for the fittings.
Can you run natural gas through a rubber hose?
Series 7132 and Natural Gas: The molecules of natural gas are small, enhancing their ability to permeate through standard rubber hose constructions.
Are natural gas and propane hoses the same?
The two are not interchangeable; each fuel source requires special gas utilization fittings. If you want to switch between the two, you'll need a conversion kit for the appliances' manufacturer for the installation process.
How long can a natural gas hose be?
Three- or six-foot long and accessible: The flexible connectors can't go through walls, floors or ceilings, nor can they be concealed. The flexible connector length usually is limited to 3 feet except for gas ranges and clothes dryers. For these appliances, 6 feet generally is allowed.
Can PVC be used for gas line?
Due to the nature of PVC and other plastics as well, they are not well suited to use for fuel gas or kerosene. PVC and other plastics deform easily in high temperature environments, and may leak or rupture.
Can you use vinyl tubing for natural gas?
No - unless specially made for this purpose do not use plain ordinary vinyl tubing for gasoline and other hydrocarbons.
What happens if you run a propane furnace on natural gas?
You are running the risk of ruining your furnace when you run a natural gas furnace on propane without using a conversion kit. In addition, if you do not modify your furnace or install a blower, it can cause an explosion because of the incorrect ratio of air and pressure.
What happens if you use propane on a natural gas stove?
Natural gas is a much lower pressure gas than propane and converting the appliance to one or the other gases requires that the differing pressure is compensated for. In other words, connecting a natural gas appliance to a propane piping system will result in appliance malfunction and possibly danger.
Can a propane fire pit run on natural gas?
Most propane fire pits can use natural gas, but a conversion kit is required to modify the fire pit to burn the natural gas properly at its lower supply pressure. Some propane fire pits cannot be converted to natural gas.
Can PEX be used for gas line?
PEX and PE are flexible and rated for much higher pressure than most gas lines, so they meet those basic requirements. However, they are made of a soft material that nails, rodents, and other things could potentially damage. This is why either may not be approved for residential gas line usage in your area.
What size is residential gas line?
Some homes are only equipped with gas lines that are 3/4 inch (") in diameter, as this is a standard size for supporting major appliances. Other homes may have a combination of 1-inch, 1/2-inch, and 3/4-inch gas lines.
Can you connect 2 gas hoses together?
A gas connector is used to get from the gas piping to the appliance, and that's all. Gas connectors should never be used as a substitute for gas piping. This means that if you ever see two connectors joined together, it's an improper installation.
Natural and LP Gas Hose
Run natural and LP gas through this heavy duty hose that's flexible enough for routing through walls and ceilings.
Welding Gas Hose
This hose meets CGA (Compressed Gas Association) standards for use with oxygen and acetylene gas.
Smooth-Bore Seamless Stainless Steel Tubing
This tubing has a seamless construction with no weld bead for unrestricted flow and is stronger than welded tubing.
Welded Stainless Steel Tubing
When your application does not require a smooth interior, this tubing is an economical choice.
Mil. Spec. Stainless Steel Tubing
A titanium additive gives this tubing excellent strength and superior corrosion resistance. It meets MIL-T- 8808.
Stainless Steel Tubing with Plastic Exterior
The outside of this tubing is covered with PVC for extra protection against external corrosion.
Extreme-Pressure Stainless Steel Tubing
This tubing is suitable for extreme-pressure applications reaching 15, 000 psi— the highest pressure rating of all the tubing we offer.
What is the propane torch hose used for?
This hose is often used for extended-use applications, or when a propane tank can’t be moved.
What is a CGA coupling?
These couplings consist of a plug and socket that connect and disconnect quickly. Use them if you need to frequently link and unlink welding hoses, torches, and regulators. They are also known as CGA couplings.
What is a CGA bolt?
Also known as CGA nuts, these are designed for low-pressure welding applications downstream of your pressure regulator. Attach them to barbed hose fittings for compressed gas to make a threaded connection to torches or pressure regulators.