MR. HEATER BUDDY TROUBLE SHOOTING GUIDE If your Buddy Heater shuts off for no apparent reason after 30 sec or more you will need to follow the steps below to determine the cause. To get access to the inside of the Buddy Heater you need to first remove the front wire grill (#10).
Full Answer
What are some common problems with Mr. Buddy heaters?
The instructions go:
- Inspect the device, the fittings and make sure everything is ready and safe to use.
- Attach a 1 lb. disposable propane canister that is compatible with a No. ...
- Make sure the heater and canister are in an upright position. ...
- At this point, if the heater is ready to go, press the on button for 30 seconds. ...
How to fix Mr Buddy heater?
- Simple setup
- Puts out adequate heat on high or low setting
- Excellent safety features
How do I troubleshoot Mr. heater Big MAXX?
Mr Heater BIG MAXX garage heater died???
- Melensdad. Finally got some really cold temps and my garage heater craps out. ...
- MrLovable. You didn't say if you have gas coming out. ...
- bczoom. Are you running off natural gas or propane? ...
- Melensdad. And I can see no way to manually light it.
- bczoom. Did you check/try the reset switch (es)? ...
- road squawker. ...
- Big Dog. ...
- Melensdad. ...
- Big Dog. ...
- Melensdad. ...
Are Mr. Buddy heaters safe to use indoors?
Perhaps one of the best features of the Mr. Heater Buddy is that it can be used both indoors and outdoors. Many portable propane heaters can be dangerous when used indoors due to the risk of carbon dioxide poisoning. However, the Mr Heater Buddy has a sensor that automatically turn off the heater when oxygen levels are low.
Why does my Mr Heater Big Buddy keeps shutting off?
If the thermocouple is too far from the flame, this can cause the pilot to go out and shut down the propane heater; you can fix this easily by moving the thermocouple closer to the flame. The thermocouple could also be worn out, in which case it needs to be replaced.
How do you fix a Mr heater that won't stay lit?
1:002:06Buddy heater won't stay lit | clean the fuel intake | DIY Repair - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo i used this little eyelash brush like a little scrubber i dipped it in some peroxide and then iMoreSo i used this little eyelash brush like a little scrubber i dipped it in some peroxide and then i just put it in here. And started cleaning.
How do you unclog a buddy heater?
1:4118:44Clogged "Mr. Buddy" Heater: Failure to Fire !!! - YouTubeYouTubeStart of suggested clipEnd of suggested clipBuddy says to start this thing what we do is turn it to pilot. Press down and hold it for 30 secondsMoreBuddy says to start this thing what we do is turn it to pilot. Press down and hold it for 30 seconds or a minute this allows it to purge any air that's in the lines.
How do you clean the thermocouple on a Mr heater?
1:122:30Portable Buddy - Cleaning and Maintenance - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe q-tip in the isopropyl rubbing alcohol. And slide it into the pilot tube about two inches. CleanMoreThe q-tip in the isopropyl rubbing alcohol. And slide it into the pilot tube about two inches. Clean the pilot tube thoroughly with the q-tip. Then remove and discard the q-tip.
Why is my gas heater not igniting?
If your gas furnace initiates the start cycle but does not fire up, it's likely because of a faulty, damaged, or dirty ignitor/sensor. This is a very common furnace problem—you can try to clean the sensor and replace the ignitor.
Why would a propane heater stop working?
The most common reasons for a non-working propane heater are a dirty thermocouple, a thermocouple that is too far from the flame, a blocked pilot tube, an empty/overfilled gas canister, and drafts. Fortunately, the majority of homeowners will be able to take care of these issues on their own.
How do you bypass a thermocouple?
0:146:48How to bypass your thermocouple on a propane heater - YouTubeYouTubeStart of suggested clipEnd of suggested clipThis is the thermocouple. Okay that's the thermocouple here's a main igniter wire. And here is theMoreThis is the thermocouple. Okay that's the thermocouple here's a main igniter wire. And here is the tube that gives you propane. So you follow this wire down.
What is a dump switch on a propane heater?
A dump switch is a safety device on propane heaters that shuts off the gas if the heater gets knocked over.
Where is the thermocouple on a propane heater?
1:375:35How to clean Thermocouple in propane heater-How to prepare ...YouTubeStart of suggested clipEnd of suggested clipNow the first thing that we're going to do on here is there's some screws along the edges. And we'reMoreNow the first thing that we're going to do on here is there's some screws along the edges. And we're going to remove. Those. And here's the first things here there's screws along the sides. We're
What does thermocouple look like?
The thermocouple is made up of a tube, a bracket, and wires. The tube sits above the bracket, a nut holds the bracket and wires in place, and underneath the bracket, you will see the copper lead wires that connect to the gas valve on the furnace.
Can I clean a thermocouple?
Yes, you can clean a thermocouple, but the task must be done with a light touch. Remove the thermocouple from the process assembly, using a steel wool or emery cloth, lightly clean the tip removing any build up. Cleaning a thermocouple is not a fix for an issue, such as inaccurate readings.
How do you clean carbon out of a thermocouple?
Use your pliers or wrench to remove the pilot light and thermocouple from the bracket. Using the wire brush, brush away the carbon buildup and soot from both components. For hard to reach areas and stubborn buildup, use the metal file. Wipe away dust with a soft cloth or burst of compressed air.
BUSINESS HOURS
UPCOMING SPECIAL HOURS: The office will close at 3:00 pm EST Friday, February 18th through Monday, February 21st. W e will resume seasonal business hours at 8:00 am EST on Tuesday, February 22nd. Thank you.
TO ORDER SERVICE PARTS ONLY - IN CANADA
For Canadian customers only - If you know which part number (s) to order, please visit LionCove Canada to place your order.
How many lbs does a Big Buddy heater use?
To avoid this problem, the hose can be replaced with one that has a pressure reducing regulator. The Big Buddy Heater uses one- or two-pound pro pane tanks that need to be refilled constantly, making it fuel inefficient.
Why is my Big Buddy heater clogged?
When using the Big Buddy Heater with the 20-pound tank, the regulator and control valve can get clogged by residue formed due to the high PSI from the propane tank. This can be avoided by turning off the tank first and allowing the fuel left in the hose to burn up completely, rather than just switching off the heater.
Cause 1: Dirty Pilot
The pilot keeps your heater ignited. If your heater pilot is dirty, it won’t light. So a dirty pilot can be the culprit behind Mr Heater not staying lit. Carbon, oil, spider web, and other types of debris build-up can be why the pilot light is not working. And as a result, turning off the heater as well.
Cause 2: Improper Draft Positioning
The draft allows air supply in the heater system. The heater works with the help of this air. But if there is too much airflow, then the heater will not stay lit. Excessive air will blow the fire out.
Cause 3: Dirty Thermocouple
A dirty thermocouple is another culprit behind your mr buddy heater keeps shutting off. Thermocouple signals the heater gas valve when to open and when to close. A dirty thermocouple will fail to do it. It will signal the gas valve to close when it is not needed. As a result, the gas supply will stop, and the heater won’t stay lit anymore.
Cause 4: Faulty Gas Valve
The gas valve supplies the fuel in your heater. Your heater doesn’t work without this fuel. And this is precisely what happens when the gas valve is faulty.
Cause 5: Dirty Pilot Orifice
The pilot orifice controls the flow of the gas to the pilot. You already know that if your buddy heater pilot won’t light, the heater will not stay lit. Again, if the pilot orifice is faulty, it will prevent the activity of the pilot. So basically a dirty pilot orifice will eventually cause the whole heater to shut down.
Cause 6: Faulty Flame Sensor
The flame sensor signals the heater to function appropriately. It reads the atmosphere of the heater and sends commands to the heater system. The sensor will read wrong signs if it’s dirty. As a result, it will command the heater to turn off. This is the same as the heater not staying lit.
GUESTS
If You want access to member only forums on FM, You will need to Sign-in or Sign-Up now .
Question
i just got a new buddy heater the other day. today was the second time i used it.
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
1. Malfunctioned Sensor
Whenever the pilot light will not ignite, this signifies a problem in the device sensor. Sensors are programmed to detect heating problems.
2. Clogged Pilot Tube
If you’re still having bad issues with Mr. Heater Pilot Light, try to assess the pilot line or tubing. This part usually accumulates dirt and unwanted debris when frequently used.
3. Dirty Thermocouple
Another culprit behind the troubleshooting of your heater is a dirty thermocouple. A thermocouple works by directing heater gas valves when to operate in opening and closing.
4. Damaged Gas Valve
Technically, gas valves are responsible for fueling up the heater to make it work. If this becomes damaged due to clogged dirt or debris, the heater won’t light.
5. Defective Electronic Spark Mechanism
If you happen to guess that the electronic spark mechanism is defective as the blower is turned on. Well, you must reroute the wirings of the heater. And to do this, proceed to the steps below.
6. Clogged Burner Orifice
When the pilot heater does not light properly, there may be a lot of reasons behind it and one of them is the dirt burner orifice. Using a heater gathers dirt and debris over time.
Small Pilot flame on MrHeater MHBF20lpt & pilot won't stay on
You will probably need to remove the pilot orifice and clean it out use a small needle or orifice cleaning rod. The pilot flame is not big enough to keep the thermocouple engaged.
When I press down and
When the pilot lights continue holding the button down for a full minute and then release. It should stay lit then to allow you to turn it to the on position. If the pilot will not stay lit after holding it for the full minute, then the thermocouple will need to be replaced. Hope this helps.
Mr. Heater Big Maxx - Green light is off. I put in a new 3 amp fuse (even thought the original looked ok) and light is still off. Checked wires at connection and have good volts. Basically new unit
With multimeter check l1 to ground on control board. Also check 24vac to ground to verify high and low voltage present at board.
My mr. Heater lights only stays lit for about 3 minutes and then it goes out
I had this same problem with my heater. I cleaned the propane tube where the flame comes out (after it’s off and cooled down) with a Qtip and some alcohol. After removing some cotton, it will fit all the way down to the end of the tube. Repeat until it comes out clean and stays lit.
Pro installed new Mr. Heater 2500btu radiant natural gas heater to Mr.Heater specs. when checked ceiling and the wall are hot 180 degrees is this normal or is something wrong or need heat shields?
There is nothing on line about heat shields I would go direct to M r heater with model and serial number and ask them .
Why does my Big Buddy Mr. Heater make a whistling or humming noise?
mr heater makes a whistling sound as gas escapes around the gasket of the ceramic heating elements, that is ,all around the outside edges of the ceramic heating elements.
How do i disable the oxygen sensor on a mr buddy heater
The responses so far I don't believe are answering the question. Instead, they are mentioning potential problems not related to the question.
Thank you for your interest in Enerco Group Inc
The following contact information is provided for consumers and businesses who have questions regarding the company and its products. By selecting the appropriate contact information below, you will ensure your inquiry will be answered in an expedient manner.
TO ORDER SERVICE PARTS ONLY - IN CANADA
For Canadian customers only - If you know which part number (s) to order, please visit LionCove Canada to place your order.
ATTENTION BUDDY CUSTOMERS
There have been a few model changes this year to our Buddy line of heaters.