KINGWIRE MHF Cable
| Conductor (AWG or kcmil) | Insulation Thickness (mils) | Cable O.D. | Weight per 1000 ft. (lbs) | Ampacity |
| 2-2-4-6 | 60 | 0.884 | 295 | 100 |
| 2-2-2-4 | 60 | 0.909 | 343 | 100 |
| 2/0-2/0-1-4 | 80 | 1.180 | 562 | 150 |
| 4/0-4/0-2/0-4 | 80 | 1.380 | 799 | 200 |
Full Answer
Can a service entrance be installed on a manufactured home?
1.1 Service entrance installations for manufactured homes, shall meet all requirements referenced above, where applicable. 1.2 Service entrance installations are subject to approval by any local code enforcing official, where they exist. Where they exist, no service entrances will be energized without such approval.
What is a mobile home electrical connector used for?
Intended for the connection of mobile homes to a supply of electricity where permanent wiring is required. Used for secondary-distribution and underground-service applications at 600 volts or less. Intended for the connection of mobile homes to a supply of electricity where permanent wiring is required.
What kind of cable do you use for underground service entrance?
Underground Service Entrance Cable. 600 Volt. Alumaflex® Brand Aluminum Alloy (AA-8176) Conductor. Cross-linked Polyethylene (XLP) Insulation. Sunlight Resistant.
What is service entry cable used for?
Used to convey power from the service drop to the meter base and from the meter base to the distribution panelboard. Southwire's SER copper service entry cable is used for dryers, A/C units, ranges and heat pumps. It can also be used for breaker boxes in multiple unit buildings.
What type of cable is used for service entrances?
SER is a type SE (service entrance), Style R (reinforcement tape) cable, used as an above ground service entrance cable, a panel feeder and in branch circuits. It is most often used to deliver power from the service drop down to the meter base, and from the meter base to the distribution panel board.
What kind of wire do you use for a mobile home?
In short, if you are looking at buying a used mobile home, make sure it has copper wiring. Electrical wiring in mobile homes built after 1971 is copper. Copper is the best to use when it comes to conductivity, reliability, and strength.28-Nov-2017
What size wire do I need for 100 amp service?
For 100 AMP service, you'll need a #4 AWG copper wire or #2 AWG aluminum or copper-clad wire. Make sure to limit your voltage drop to 3% regardless of distance.
What size wire do I need for a 200 amp service?
Installation of 200 amp electrical service needs a #2/0 AWG copper wire or #4/0 AWG for aluminum or copper-clad wire inside a minimum of 1.5 inches, schedule 40 or 80 PVC conduit for underground service. However, 2 or 2.5 inches is recommended if running 3 wires in the same conduit.20-Jun-2021
What gauge is mobile home wire?
2 AWGProduct DetailsCable TypeMobile Home FeederWire Size2 AWG# of Conductors4 ConductorsConductor MaterialAluminumStranded or SolidStranded10 more rows
Can you use aluminum wire service entrance?
However, in larger-capacity circuits, such as a main service entrance for a house, or in a situation such as yours—a feeder from the main electrical panel to a subpanel—aluminum cable may still be permitted.
What is #2 aluminum wire rated for?
USE- 2 is approved for direct burial and for service entrance below ground. USE-2 cables may be used in wet or dry locations, with conductor temperatures not exceeding 90°C. Voltage rating for USE-2 cable is 600V.
How many amps will #6 aluminum wire carry?
Allowable Ampacities of Insulated Aluminum or CopperClad Aluminum ConductorsConductor Size (AWG/KCMIL)60°C (140°F) TW, UF75°C (167°F) RHW, THHW, THW, THWN, XHHW, USE, ZW8354064050455653657520 more rows
How many wires do I need for a 100 amp sub panel?
This is typically a three-wire cable with three insulated conductors plus a bare copper ground wire. The cable must have a wire gauge sufficient to the amperage of the subpanel—a 100-amp subpanel requires #4 copper wires or, more commonly, #2 aluminum wires, for example.
What size wire do I need to run 300 feet?
for 300 feet for 100 amp rated service I would use Aluminum direct burial 1/0-1/0-1/0-1/0, the forth can be as low as #4 for the ground (but also in conduit, even if in conduit must still be rated underground wire and required by code also) Also note the size wire the breaker can handle, cannot cut strands to make fit, ...28-Jul-2014
How do you wire a service entrance panel?
1:237:26Episode 16 - Service Entrance Wiring - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo we've got the two inch hole going out to the building. And there's a piece of two-inch PVCMoreSo we've got the two inch hole going out to the building. And there's a piece of two-inch PVC conduit connecting the two boxes. We use the lock ring as well as a this plastic bushing that's required.
What size wire is needed for a 300 amp service?
300 amp. For 300 amp service, you will want copper wire of size 500 kcmil to handle the load.