Check the Maytag Washer’s Water Supply If the water valves or faucets for hot and cold water are not fully open or turned on, the washer will not continue or proceed with the cleaning cycle. If you attempt to start the Maytag washer without water, then the machine will stop and display an “F8E1” error code on the console.
Why is my Maytag washing machine not starting?
- Activate the power button.
- Test the outlet.
- Reset outlet if necessary.
- Make sure the power cord is plugged in.
- Check if fuses are blown or the circuit breaker is thrown.
- See if Delay Start has been pushed.
- See if Control Lock has been activated.
Is Maytag a good washing machine?
- Option to dry machine and door to prevent musty smell
- Automatically adds the correct amount of detergent
- Can wash and dry a small load
- Door gasket, drawer, hose and other parts are treated to prevent germ growth
How do you fix a Maytag washer?
Rotating the dial
- Set the dial to its standard or normal position, facing up at 12 o’clock.
- Rotate the dial counterclockwise back to the standard position you started in.
- Turn the dial clockwise three settings so that it is in the 3 o’clock position.
- Turn the dial clockwise one setting.
- Turn the dial counterclockwise once to return it to the 3 o’clock position. ...
How to troubleshoot a Maytag washer on Spin Cycle?
To check the clutch, you need to:
- Turn the washer on a cycle.
- Check if the tub is rotating around at all: When it doesn’t rotate at all, it’s likely the clutch is worn out. ...
- If the clutch is worn out, you’ll need to replace it.
Why does my washer turn on but not start?
First, make sure the power is on and that the machine is plugged in. You should check the outlet to make sure it's working. Then, check if a fuse is blown or a circuit breaker thrown. If those both work, see if the Delay Start button or Control Lock feature has been activated.
What causes a Maytag washer not to start?
The line fuse blows if the washer circuits are overloaded. If the line fuse blows, the washer won't start. To determine if the line fuse is at fault, use a multimeter to test it for continuity. If the fuse does not have continuity, replace it.
Is there a reset button on Maytag washing machines?
The Maytag washer doesn't have a reset button. If you need the reset button, you have to use the 'Power/Cancel' button. Push it to stop the current cycle. Select a new cycle and then press 'Start/Pause.
Why is my Maytag washer not going through cycles?
Common solutions for: Maytag Washer stops mid cycle If the door lock is defective, the washer may stop mid cycle. The door lock can fail either mechanically or electrically. Inspect the door lock for damage. If the door lock is damaged or does not latch properly, replace it.
How do I get my Maytag washer to start?
0:151:35How to Start Using Your New Maytag Top Load Washing MachineYouTubeStart of suggested clipEnd of suggested clipEnjoy congratulations on the purchase of your new Maytag washing machine to get things startedMoreEnjoy congratulations on the purchase of your new Maytag washing machine to get things started select the power button. Turn the knob to select a cycle for your laundry. Load.
How do I reset my Maytag washer?
Press and hold the Start/Pause button for 3 seconds. All indicator lights should be off at this point. Reset the Washer: To reset (clear) the washer, rotate the Cycle Selector Knob counter-clockwise (left) to clear any sequence.29-Apr-2021
How do you reset the lid lock on a Maytag washer?
Once paused, the lid automatically unlocks to allow changes to the current load.Touch "Cycle Signal" near the front-loading washer's LCD control panel to deactivate the washer's lock controls. ... Push "Start/Pause" to temporarily halt the washer's current cycle, and wait for the indicator light below "Pause" to light up.More items...
How do I reset my washing machine?
1:173:47Washer Not Spinning - How to Reset Motor (Easy) - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe machine gives you 30 seconds to lift the lid and close. It six times and once you start liftingMoreThe machine gives you 30 seconds to lift the lid and close. It six times and once you start lifting the lid. You have 12 seconds to do the six repetitions.
What does the Maytag extra power button do?
Extra Power Button: Boosts drying power on any cycle by extending time, heat and tumbling. One push helps prevent underdrying by getting thick fabrics, pockets and seams drier the first time².
Why is my washer not finishing its cycle?
For a front-load washer, a broken washer door lock assembly, failed main electronic control board or faulty motor control board can prevent the washer from finishing a cycle. This type of washer often signals a digital error code when the washer control detects a problem and stops the cycle.
Why won't my washer finish the cycle?
Possible Causes One common issue that can cause a washing machine's cycle to stop is the heater to stop working properly. To test this set your washer on a cycle and monitor it every so often, if the cycle stops within the first 30 minutes then the water likely isn't getting sufficiently heated.
Why won't my washing machine complete its cycle?
If a washer stops mid-cycle, it could be because the pump or the motor that runs it has failed. When this happens, it cannot remove the water efficiently, pump water in, and thus the sensors won't allow it to move to the next cycle.09-Sept-2019
1. Incorrect Cycle Setting
Maytag washing machines have a wide range of settings, but the most common washer problems, like an incorrect wash cycle or spin setting, can all be easily corrected with a few clicks on your control panel. Use the gentle cycle when washing delicate items or those that are prone to stretching.
2. Washer is Unbalanced or Overloaded
Maytag washers are known for their strength and durability. Although they spin clothes very well, certain washer conditions can impact the spinning capacity. For instance, if the washing machine is overloaded or there’s a large item (for example, a blanket) in the washer, clothes may not be spun dry.
3. Defective Lid Switch Assembly
By closing the lid on your Maytag washer, the lid switch assembly is activated and causes the washer to turn on. While this system is convenient, it can become faulty over time — causing the washing machine not to turn on when the lid is closed.
4. Faulty Drive Belt
A washer drive belt connects the motor to the main drum. A damaged belt can prevent your washer from spinning, which then causes the clothes to sit in a wet mess. Two pulleys on either side of the drum connect the belt to the motor and help turn the drum during a cycle.
5. Failed Motor Coupling
If the washer spin cycle isn’t working, there are a number of possible causes. For example, if a motor coupling is faulty, it could be responsible for a washer spin cycle problem. A motor coupling links the transmission and motor so power can reach the washer drum.
6. Defective Door Latch
The washer door latch is a device that keeps the washer door shut during operation. It’s made of durable, high-quality material, and it prevents the washer from operating without its washer door shut. The latch also has a soft surface to prevent damage to the laundry tub.
Why won't my Maytag washer turn on?
If the outlet is receiving power to turn the appliance on, but the Maytag washer still will not power on, it can be an issue with a defective power cord. In this case, you can use a multimeter to test the power cord for power.
How to fix Maytag washer that won't turn on?
To fix your Maytag washer that will not turn on or off, ensure that the washer is connected to an electrical power source, and test the washing machine’s water supply lines. You should also check for mechanical failure in the washer and resolve any error codes displayed on the device.
How to stop Maytag washer lid from closing?
Check the Maytag Washer’s Door/Lid Lock. Often there may be debris or detergent build-up that can stop the lid from closing completely. If you notice any obstructions, use water, mild cleaning soap, and a cloth to clean the area and wash away the debris gently.
How long does a washer pump out?
The washer’s lid will lock automatically, and the appliance will enter a pump out mode for about 8 minutes.
What happens if you don't turn on the water valve on a Maytag washer?
If the water valves or faucets for hot and cold water are not fully open or turned on, the washer will not continue or proceed with the cleaning cycle. If you attempt to start the Maytag washer without water, then the machine will stop and display an “F8E1” error code on the console. The water supply needs to connect to the washer before starting the washing cycle.
How long does it take for a washer to start?
Depending on the washer model, you might have to press and hold down the start button for approximately 3 seconds to start the cleaning cycle. If the display board does not function properly, then the controller may not correctly engage the appliance to operate.
Does Maytag front load washer have a control lock?
According to some Maytag top-load and front-load washer models, there is a control lock feature on some units. When this lock feature is activated, there will be a control lock light displayed on the machine. The washer’s controls will not work and will not respond to any commands via touch if you attempt to push any buttons on the washer console.
Electronic Touch Pad Information
When using the touch control, touch on the name to operate, not the lights.
Is the control locked (control on the back console)?
If the Control Lock feature is activated, the Control Lock light will be on. The controls will not respond to any touch commands.
Is the lid locked?
The lid must be completely closed and latched for the washer to operate.
Is the lid completely latched?
The lid must be completely closed and latched for the washer to operate.
Did you receive an "LF" or "F8E1" Error Code?
If F8 E1 or LF (too long to fill) appears in the display, the washer is taking too long to fill, or the washer is filling and draining.
Are you using anti-flood devices and controls?
Whirlpool recommends that appliances be directly connected to the water supply for optimum machine performance.
Still need help? Contact us or schedule service
Please contact us or click below to make an appointment from our preferred list of service providers for service on your appliances.
Caution!
Before performing any repairs on your Maytag washer, always disconnect it from its power supply to prevent electrocution and reduce your overall injury risk.
Incoming Power Supply
When troubleshooting a Maytag washer that won’t turn on, your first step should be to check the incoming power supply.
Corroded Contact Pads On User Interface
The user interface on your Maytag washer is the front-facing section that you use to interact with the appliance.
User Interface Or Control Panel
As mentioned in the previous section, the user interface (sometimes referred to as the control panel) is the part of your Maytag washer that you use to control the appliance. The front-facing part of the washer with buttons you press to input settings for the wash cycle.
Wiring Between User Interface And Main Control Board
As we’ve seen a few times earlier, there is a wire harness that connects the user interface directly to the main control board. This wire harness is critical because it sends signals to the control board whenever you input settings on the interface.
Main Control Board
The main control board is the brain of your Maytag washer. It is a printed circuit board containing many electrical and electronic components responsible for coordinating the different components and tasks necessary to complete a wash cycle.
Is the Washer in Stand-By mode (plugged in with all indicators off)?
The washer must be in Stand-By mode to set the sequence of turning off the washer.
If all lights flashing (except Lid Locked) continue to next step
Rotate the cycle selector knob (either direction) until the LED lights display with ONLY "Wash, Rinse, and Done" turned on. See picture below. For units with a display, "13" should show in the display.
Still need help? Contact us or schedule service
Please contact us or click below to make an appointment from our preferred list of service providers for service on your appliances.
Interested in purchasing an Extended Service Plan?
Please click below to learn more on how you can save up to 25% on New Appliance Extended Service Plans within 30 days of your appliance purchase.
Why won't my washer start?
The 6 Common Reasons Why Your Washing Machine Won’t Start. Whether you wash clothes every day or once a week, having that washer in your home is an essential luxury of home. No laundromat, no laundry service. You can throw in a load of clothes and enjoy the dryer-fresh result in a couple of hours. Until your washer stops working.
How to tell if a washer motor is bad?
The washer motor will require professional repair. But you can often tell if the motor is the issue just by listening. Motors tend to hum, whir, whine, and buzz when they start to fail. A washer that has grown increasingly loud or with irregular motor sounds is one with a failing motor. If you hear your washer try to start and then fail, then your motor has failed.
How to stop a washer from shaking?
Start by checking behind the washer for the power plug. It is surprisingly common for the washer’s shaking to pull its own power plug out of the wall. That will stop it from running pretty quickly, and is more likely to be the case if your washer stops partway through a cycle.
What is a faulty start switch?
The timer is what controls which cycle is running and when your washer stops and starts each cycle .
What is the main control board on a washing machine?
Older washers have fairly simple main control boards while newer washers are small computers in their own right. The main control board is what receives all the wires from the various components and controls the washer accordingly.
Why does my breaker flip?
A breaker flips when one circuit is overloaded either with supply or demand. For example, running two appliances off the same circuit can flip a breaker. As can a lightning strike or a power surge. Locate your breaker box and open it up.
Which way should a breaker be flipped?
All the breakers should be flipped in the same direction (sometimes two columns are direction-opposite). If one breaker is in the center or pointing to the wrong side, flip it to the “off” position, then the “on” position to restore the power.