Receiving Helpdesk

liftmaster learn button location

by Augustus Haley Published 3 years ago Updated 2 years ago

Learn buttons that are red, orange, green or purple will be large, square buttons located under the light lens on the back panel of your garage door opener. To program a new garage door remote, press and quickly release your learn button to trigger the machine's programming mode.

Full Answer

Where is the learn button on a Liftmaster 8500W?

Programming remotes and keyless entry

  • Using a safety pin or paper clip, press the program button on the side of the remote, until the LED light on the front turns on.
  • Press and release the learn button twice. ...
  • Press and release the remote button you wish to program, one time.
  • Exit the programming by pressing one of the other 2 buttons on the remote.
  • To test, press the programmed button.

Where is located learn button?

  • Press and hold the POWER button located at the mounting base to turn power off (green LED light will turn off).
  • Press the POWER button until the green LED light illuminates.
  • Wait 3 seconds.

Where is the Genie learn button?

  • Press and release the learn code button - the red LED will begin to blink.
  • Press the desired HomeLink button one time. The red LED will stop blinking and stay on.
  • Press the desired HomeLink button one more time. The red LED will go out.
  • Pressing the HomeLink button again will cause the garage door to move. ...

How to find the learn button on my garage door opener?

  • Find the Learn Button on the Garage Door Opener. The "Learn" button on your garage door opener is located above the antenna wire that hangs from the motorhead, it may ...
  • Location of Learn Button on Garage Door Opener. The pictures below show the location of the garage door opener's Learn button depending on the light cover configuration.
  • Programming Remote Controls and Clear Garage Door Opener Settings. The "Learn" button on a garage door opener has two functions. ...

Where is the LiftMaster learn button?

The "Learn" button on your garage door opener is located above the antenna wire that hangs from the motorhead, it may also be under a light cover. The "Learn" button will be either green, red/orange, purple or yellow.

How do I pair my LiftMaster garage door opener?

2:193:04How to Program LiftMaster's 891LM and 893LM Remote Controls to a ...YouTubeStart of suggested clipEnd of suggested clipAnd hold the button on the remote until the lights on the garage door open or blink or the openerMoreAnd hold the button on the remote until the lights on the garage door open or blink or the opener makes a clicking sound. That's.

How do you use a LiftMaster learn button?

To program a new garage door remote, press and quickly release your learn button to trigger the machine's programming mode. The light located above the button will then come on and stay lit for 30 seconds. If you need to clear the memory of your garage door opener, press and hold your opener's learn button.

What is the Learn button on a garage door opener?

The Learn/Program button on residential garage door openers is used to program various accessories, clear the opener's/operator's memory, set travel and force adjustments, and depending on your model enable Wi-Fi programming.

What is the number to Banko garage door opener?

To learn more about our garage door opener services, call us today at 813-882-9900 or complete our online form to request additional information.

How to clear MyQ remote?

The first press of your learn button will clear remote control and keyless entry connections. To do this, press and hold the learn button. The light will turn on for six seconds and then shut off. To remove the memory of MyQ accessory connectivity and door controls, press and hold the learn button within three seconds of the first light turning off.

How long does it take for a garage door opener to turn off?

The light above the button will turn on and shut off after six seconds have elapsed. Once the light is no longer on, your garage door opener will be cleared of previous keyless entry and remote control connections.

How to program a garage door remote?

To program a new garage door remote, press and quickly release your learn button to trigger the machine’s programming mode. The light located above the button will then come on and stay lit for 30 seconds. If you need to clear the memory of your garage door opener, press and hold your opener’s learn button. The light above the button will turn on ...

Where is the learn button on a Liftmaster garage door opener?

Once you’ve located your LiftMaster garage door opener’s learn button, likely located on the back panel of your LiftMaster machine , you can now use this feature to easily and quickly program garage door remotes or other accessories.

Where is the learn button on Liftmaster?

To locate your LiftMaster remote learn button: First, find the antenna dangling from the bottom of the machine. If you have a light cover placed over the control panel, remove it to easily view the dashboard. Find a brightly colored — red, green, purple or yellow — square or circular button on the back panel, likely located under the light lens.

How to put an opener in programming mode?

To put opener in Programming Mode: Press "Program Set" button for 2 - 3 seconds and release when Blue or Purple LED light (s) turn On. If Purple LED light is blinking on and off, then STOP, opener is in programming Mode. If a Blue LED light is on, then press and release Program Set button again.

Where is the learn code button on a garage door opener?

The learn button may be located under a light lens in the front or back of the garage door opener .

Using the Learn Button to Program Your Garage Door Opener

Once you have found the learn button on your LiftMaster garage door opener, which is usually on the rear panel, you should use it to configure garage door remotes or other accessories quickly and efficiently. The color of your garage door opener’s learn button will significantly impact how you program your device.

Circular Yellow Colored Buttons

If your machine has a circular yellow learn button, the methods to set the controls and clean the machine’s memory are slightly different. Push and release the learn button, and the LED light above or near the button will turn on and stay constant for up to two minutes, allowing you to program remotes and accessories.

How Can You Clear the Device Memory?

There are two methods to clearing the memory of your garage door opener:

How do I Connect My Liftmaster to My Automobile?

After you press and release the learn button on your garage door opener, you should press and hold the HomeLink button on your car for 30 seconds. By pressing and holding the HomeLink button, the automobile will be connected to the machine’s signal. The light on your LiftMaster machine would blink once if the pairing were successful.

About the Author: Ran Kroynish

Ran Kroynish - 15 Years Of Garage Door Experience - At Elite Garage & Gate, Experience counts! Our years of experience in the garage doors installation and repair business has made us experts in this field.

Why is my learn button orange?

If your learn button appears to have a different color, it may be that the color has faded over time with use. For example; a purple learn button may fade to appear brown, or a red learn button may fade to appear orange.

How many colors of learn buttons are there?

There are four colors of learn buttons that are currently supported by The Chamberlain Group. Over time the color of the learn button on your garage door opener may fade and this article will help you in verifying the color of your device's learn button.

What color is the antenna wire on a garage door opener?

The antenna wire is hanging from the garage door opener and should match if the learn button color is purple or yellow. For the red/orange and green learn button the antenna is gray.

Where is the model number on a garage door opener?

The model number on a garage door opener can be found on the opposite side of the antenna. Pull the light lens cover down and you will see the model number on a label next to the light socket. Once you have your model number, use the search bar above to locate the owner's manual. For more help, see Locate Model Number .

Find the Learn Button on the Garage Door Opener

The "Learn" button on your garage door opener is located above the antenna wire that hangs from the motorhead, it may also be under a light cover. The "Learn" button will be either green, red/orange, purple or yellow.

Location of Learn Button on Garage Door Opener

The pictures below show the location of the garage door opener's Learn button depending on the light cover configuration.

Programming Remote Controls and Clear Garage Door Opener Settings

The "Learn" button on a garage door opener has two functions. ( Note: Wi-Fi-enabled garage door openers have a third function of activating the Wi-Fi learn mode.)

A B C D E F G H I J K L M N O P Q R S T U V W X Y Z 1 2 3 4 5 6 7 8 9