What does the lid switch do on a Kenmore washer?
The lid switch on your Kenmore washer completes the electrical circuit when the lid is closed. When your washer will not operate, you need to troubleshoot the lid switch before investigating other possible causes. The best way to test the lid switch is with a volt-ohm meter.
How do I remove the top panel of my Kenmore Elite washer?
To avoid risk of electric shock, unplug the washing machine. Using a 5/16" socket wrench or an adjustable wrench, remove the three screws from the top rear of the washer. Lifting from the rear, remove the top panel.
What should I do if my Kenmore washer is not working?
When your washer will not operate, you need to troubleshoot the lid switch before investigating other possible causes. The best way to test the lid switch is with a volt-ohm meter. If you do not have a volt-ohm meter, you can bypass the lid switch using a jumper wire to simulate the connection to the washer wiring harness.
How do you wire a Kenmore washer harness?
Grasp the wiring harness connector with your fingers and pull it away from the lid switch plug. Strip a 1/4-inch of insulation from each end of your jumper wire with a pair of wire strippers. Plug the washer power cord into the wall outlet.
How do you bypass the lid switch on a Kenmore washer model 110?
1:072:52Bypass lid switch kenmore washer - YouTubeYouTubeStart of suggested clipEnd of suggested clipOff. Okay take these two wires and twist them together clockwise. Turn them clockwise take a smallMoreOff. Okay take these two wires and twist them together clockwise. Turn them clockwise take a small wire nut take your wire nut screw that on there.
How do you replace the lid switch on a Kenmore model 110?
1:313:47Kenmore Top-Load Washer Lid Switch Assembly WP8054980YouTubeStart of suggested clipEnd of suggested clipUsing a Phillips head screwdriver unthread the lid switch mounting screws lift up the washer lidMoreUsing a Phillips head screwdriver unthread the lid switch mounting screws lift up the washer lid depress. The tab and you can remove the old assembly.
How do you bypass a 3 wire lid lock switch?
0:522:02Lid switch bypassing whirlpool washer - YouTubeYouTubeStart of suggested clipEnd of suggested clipThis is a noir style lid switch disconnect the wire harness from the lid switch. Place the jumperMoreThis is a noir style lid switch disconnect the wire harness from the lid switch. Place the jumper wire between the gray and white wires. And put electrical tape on it to insulate the connection.
Where is the lid switch on a Kenmore washer?
2:5710:01Broken Lid Switch Washer Repair - Kenmore or Whirlpool - YouTubeYouTubeStart of suggested clipEnd of suggested clipI've seen some reviews of people getting the wrong kind. So there's a couple screws in the back ofMoreI've seen some reviews of people getting the wrong kind. So there's a couple screws in the back of here. That. I have to undo. And then we should be able to look inside to undo this like I said I
Can I bypass the lid switch on my washer?
3:246:16Washing Machine Won't Spin - Lid Switch Bypass - YouTubeYouTubeStart of suggested clipEnd of suggested clipThis switch. So that the washing machine thinks the lid is closed. So that you can simply drain theMoreThis switch. So that the washing machine thinks the lid is closed. So that you can simply drain the water out of your washing.
How do you take apart a Kenmore washer model 110?
0:253:22Disassemble Whirlpool/Kenmore Direct Drive Washer - YouTubeYouTubeStart of suggested clipEnd of suggested clipThey have spring clips. They have to slip a putty knife underneath to release them. Once you haveMoreThey have spring clips. They have to slip a putty knife underneath to release them. Once you have your screws out slide the control panel forward about 1/2 an inch.
How do I reset the lid lock on my washing machine?
If your lid lock light is flashing, you can unplug your washer for 10 minutes and plug it back in to reset the washer and the flashing light. You can also press and hold the 'End of Cycle' button for 20 seconds to reset the washer and flashing lid lock light.
Why is my washer lid not locking?
0:061:32Top-Load Washer Lid Won't Lock - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou will need to replace it with a new. One the main control board controls when the lid lock shouldMoreYou will need to replace it with a new. One the main control board controls when the lid lock should secure the lid and release it so a faulty board might be the cause of a lid not locking when it.
Why is my washer stuck on lid lock?
– Lock striker that presses down on the lid switch may be out of alignment. – A piece of lint or washing machine detergent has built up over time and hinders the locking of the lid. – The control board sees an open lid switch when it attempts to lock.
How do you replace a lid switch on a Kenmore washing machine?
0:262:01Replacing the Lid Switch in a Direct-Drive Washer (Kenmore ...YouTubeStart of suggested clipEnd of suggested clipOut remove the screw from the green ground wire and release it remove the lid switch mounting screwsMoreOut remove the screw from the green ground wire and release it remove the lid switch mounting screws release the lid switch wire harness from the clips. And pull the lid switch out of the cabinet.
Where is lid switch on washing machine?
The lid switch is located near the top of the washer in the front so you won't need to move the washer out to access it. Inserting a putty knife under the top lip of the front cabinet of the washer, you will need to release the clip springs on each side. This will allow you to lift up the top of the washer.
How do you replace a lid switch assembly?
1:193:22Washer Not Spinning? Replace Washer Lid Switch #3949238YouTubeStart of suggested clipEnd of suggested clipYou can use a flathead screwdriver to assist in detaching the harness. Remove the old lid switch byMoreYou can use a flathead screwdriver to assist in detaching the harness. Remove the old lid switch by using pliers to evenly squeeze both sides of the wire connector.
How to replace a lid switch on a washing machine?
I strongly recommend that you not leave it this way especially if there are small children around. First unplug the machine. Lift the lid and remove the two screws holding the switch in place and pull the switch out from under the top. Cut the two wires on the switch. Strip off a half inch of insulation on each wire and wire nut or tape together. Happy New Years!
What happens if the lid switch is left bypassed for too long?
You remember what happened to the cat that got curious, don't you? If the lid switch is left bypassed for too long the machine will self-destruct. OK, it's to keep you from getting hurt: Three-year-old boy has arm ripped off by washing machine - Mirror Online
Can you use a wire nut on a washing machine?
A wire nut is ok temporarily til you get the lid switch replaced but if you intend to just leave it this way, you should only use closed end crimp connectors. Wire nuts should never be used in washing machines due to vibration issues. Same reason we don't use them on boats, auto's, planes, trains...etc.
What happens if my washer doesn't drain?
Washing machine drain pump. The pump mounts directly to the motor with two clips. If the washer does not drain then the pump could be locked up or a small object may be clogging it. A small leak in...
What is a counterbalance spring on a washer?
Washing machine tub counterbalance spring. This spring offsets the weight of the motor on the front of the washer. If broke, the tub will lean forward and the tub will be off balance during the spin...
Featured parts for Kenmore Washing Machine
Washer drive motor coupler. New style with metal sleeves for added strength. This version replaces all previous motor coupler styles and versions. For direct drive washing machines. Common symptom of failed coupler is washer will fill, not agitate or spin but will drain the water from the tub.
Kenmore Washing Machine Model 110.27612600 Parts
Kenmore Washing Machine Model 110.27612600 Parts are easily labeled on this page to help you find the correct component for your repair. Filter results by category, title and symptom.