Troubleshooting A Kenmore Washer With A Locked Lid
- Before you do anything, unplug the machine and put on protective gloves. You don’t want to have a shock!
- Start by taking a closer look at the latch of the door. ...
- Inspect the latch. Does the latch mechanism look cracked or loose? Perhaps it looks jammed? ...
- The next thing you will need to do is check your door lock and switch assembly. Your machine’s owner’s manual will help you locate both. ...
- Next, grab a multimeter and check both of the switches. The assembly can also have an electrical failure. The multimeter will be able to tell you if your switches shorted. ...
- Grab a flashlight and get an even closer inspection of the lock itself. If you notice small details that don’t look right, it’s probably the lock. ...
- Replace the back assembly once everything is fixed, then turn your attention to the door. You may need to manually open the door, if you haven’t already.
- Check to see if the door’s strike and catch are intact. If they are not, then that’s what’s causing the perma-lock you’ve been struggling with. ...
- Then, take a closer look at the lid’s hinges and pins. Stuck hinges can happen due to a buildup of lint. ...
- Once everything has been properly fixed, close the door and check to see if the lock works. ...
Why won’t my Kenmore washer lid unlock?
Kenmore Washer Lid Won’t Unlock? (We Have a Few Fixes) The lock function on a Kenmore washer is great, that is until it won’t unlock. This can happen for several reasons from the latch to the switch assembly. Follow along as we explore how you can identify and fix the cause of a Kenmore lid that won’t unlock.
What does a door lock do on a Kenmore washer?
The door lock secures the washer door shut during operation. Once the washer door is closed, the washer can begin operating. If the door lock is defective, the washer door will not latch properly. The door lock can fail either mechanically or electrically.
How do I test the lid switch on my Kenmore washer?
The best way to test the lid switch is with a volt-ohm meter. If you do not have a volt-ohm meter, you can bypass the lid switch using a jumper wire to simulate the connection to the washer wiring harness. Unplug the Kenmore washer power cord from the wall outlet. Find the two screws securing the control panel to the top of the washer.
Why is my Kenmore washer door not closing properly?
Once the washer door is closed, the washer can begin operating. If the door lock is defective, the washer door will not latch properly. The door lock can fail either mechanically or electrically. Inspect the door lock for damage.
Why won't my Kenmore washer lid unlock?
If the washer door won't unlock the problem might be the main control board. This is not common. Normally the problem is with the lock mechanism. Unplug the machine for 5 minutes to let it reset and then plug it back in and give it a try.
How do you bypass the lid lock on a Kenmore washing machine?
1:072:52Bypass lid switch kenmore washer - YouTubeYouTubeStart of suggested clipEnd of suggested clipOff. Okay take these two wires and twist them together clockwise. Turn them clockwise take a smallMoreOff. Okay take these two wires and twist them together clockwise. Turn them clockwise take a small wire nut take your wire nut screw that on there.
How do I reset the lid lock on my washing machine?
1 – Unplug the washer for 10 minutes and this may reset the washer and clear the flashing light. 2 – Press and hold the “END OF CYCLE / CYCLE SIGNAL” button(s) for 20 seconds and this should reset the washer and clear the flashing light.
Why is the lid lock light flashing on Kenmore washer?
– Be sure lid lock and lid striker are clean as lint or detergent buildup can block the switch and cause the flashing light. – Be sure the lid lock and lid striker are aligned and secure as they can become loose from years of vibration or slamming the washer lid shut.
Will washer work without lid lock?
NO. The lid lock it to prevent injury to the people near the washer, as without it stopping the machine, the agitator will turn with the lid open. If you will open the top up, you should see the lid switch, and you should see the electric wires attached to it.
How do you test a lid switch on a Kenmore washer?
1:144:30Whirlpool / Kenmore Washer Not Draining - Lid Switch Test - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou want to say 2 meter ohms. And test those two pigs. That's a closed circuit. And that indicatesMoreYou want to say 2 meter ohms. And test those two pigs. That's a closed circuit. And that indicates that the lids closed which thatlet's which is good. Now if your lips closed.
How do you reset a Kenmore washing machine?
1:173:47Washer Not Spinning - How to Reset Motor (Easy) - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe machine gives you 30 seconds to lift the lid and close. It six times and once you start liftingMoreThe machine gives you 30 seconds to lift the lid and close. It six times and once you start lifting the lid. You have 12 seconds to do the six repetitions.
Why is my washer door not locking?
The door lock could be defective or worn out, so it no longer keeps the washer door closed. Most lock assemblies are made of plastic, so if it's defective, you won't be able to repair it, and instead have to replace it. The door lock motor and switch assembly can also be defective, either mechanically or electrically.
Why is my washing machine not locking?
0:061:32Top-Load Washer Lid Won't Lock - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou will need to replace it with a new. One the main control board controls when the lid lock shouldMoreYou will need to replace it with a new. One the main control board controls when the lid lock should secure the lid and release it so a faulty board might be the cause of a lid not locking when it.
Why is my washer blinking lid locked?
The Lid Lock Light will flash if Lid Lock has not moved into the Lock Position, the Lock Motor can not be powered, or the Lid is not closed completely due to interference. Some models will lock immediately, while others will not lock until after the wash cycle has started.
How much does it cost to replace a lid switch on a washer?
Washer Lid Switch Repair Cost Repairing the lid switch costs $140 to $190. In some instances, this repair might only take 15 to 20 minutes so your bill might swing towards the lower number.
Why is my washer blinking?
Newer model machines come with a “final spin” indicator light, this light when flashing, signals to let you know that your wash load is unbalanced. On other models, this is apparent when you remove your clothing and they are still soaking wet.
What happens if the washer door is closed?
Once the washer door is closed, the washer can begin operating. If the door lock is defective, the washer door will not latch properly. The door lock can fail either mechanically or electrically. Inspect the door lock for damage. If the door lock is damaged or does not latch properly, replace it. To determine if the door lock has failed ...
What to do if your door lock fails?
If the door lock is damaged or does not latch properly, replace it. To determine if the door lock has failed electrically, use a multimeter to test each of the door lock switches for continuity . If one of the ... switches does not have continuity, replace the switch. Required Part.
Why is my washer lid lock bypassed?
A washer’s lid lock bypass is especially discouraged in a household that has kids, because they might attempt to try and retrieve an item when the washer is running and end up hurting themselves. Additionally, if you successfully manage ...
How to display error code on washer?
If the washer is in diagnostic mode, you will turn the control dial 1 clockwise, and then press the start button. To display the first saved error code, you will turn the control dial one click clockwise, and to display the next error code, just turn the control dial one clockwise.
Can you fix a Kenmore washer that says LE?
Is it possible to fix the code in the Kenmore washer? Yes, it is possible, if you get the LE error code from your washer, you will have to check that the washer isn’t overloaded. If you use too much detergent, you will also get the error code, and the best thing to do is let the washer sit for 30 minutes without running.
Does Kenmore have a warranty?
Any interference with the normal working conditions of your washer will void its warranty, so it is best to carry out the above processes when the warranty period has expired.
Can you run a Kenmore with the lid open?
The above lid lock bypass for the Kenmore washer qualifies for the long term, however, but not recommended. Once done and are sure that the washer can run with the lid open, you will then put everything in the control panel back to its place. Important to note is that the above lid lock bypass on the Kenmore washer can only be used on ...
What happens when you bypass the lid switch on a Kenmore washer?
Warning. When bypassing the lid switch, touch only the insulated portion of the jumper wire with your fingers. The lid switch on your Kenmore washer completes the electrical circuit when the lid is closed. When your washer will not operate, you need to troubleshoot the lid switch before investigating other possible causes.
How to test a lid switch?
The best way to test the lid switch is with a volt-ohm meter. If you do not have a volt-ohm meter, you can bypass the lid switch using a jumper wire to simulate the connection to the washer wiring harness. Advertisement.
Where is the lid switch wire harness?
Locate the lid switch wiring harness on the rear of the top panel. Grasp the wiring harness connector with your fingers and pull it away from the lid switch plug.
Kenmore 110 Series Washing Machine
The Kenmore 110 Series is an easy to use home Washing machine created by Kenmore.
2 Answers
If the washer door won't unlock the problem might be the main control board. This is not common. Normally the problem is with the lock mechanism.