Receiving Helpdesk

kenmore top load washer not filling with water

by Simeon Mosciski Published 3 years ago Updated 3 years ago

Kenmore Washer fills slowly or will not fill at all If the water inlet valve

Valve

A valve is a device that regulates, directs or controls the flow of a fluid by opening, closing, or partially obstructing various passageways. Valves are technically fittings, but are usually discussed as a separate category. In an open valve, fluid flows in a direction from higher pressure to lowe…

is defective, the wash may fill slowly or not fill at all. If the water pressure is adequate, try cleaning the screens inside the water inlet valve hose connection ports. If the washer still fills slowly, replace the water inlet valve.

Part of a video titled Top-Load Washer Won't Fill: Troubleshooting Direct-Drive
0:10
6:22
If you don't have any water coming out check for a clog in the hoses. If the hoses are okay youMoreIf you don't have any water coming out check for a clog in the hoses. If the hoses are okay you could have a problem with your house water supply. If water is flowing from the supply hoses.

Full Answer

How to fix a washer not filling with water?

How to Fix a Washing Machine That Won't Fill With Water

  1. Examine Hoses. Start by pulling out the washer so you can see the hoses. ...
  2. Check Water Level Switch. The reason the washing machine won’t fill might lie with the water level switch. ...
  3. Inspect and Clean Filters. ...
  4. Check the Water Inlet Valve. ...
  5. Examine the Pressure Chamber. ...
  6. Check for a Very Slow Flow. ...

Why is my Kenmore washer not spinning or draining?

Kenmore Washer Not Spinning – Troubleshoot and Diagnosis

  1. Check the Wash Cycle and Spin Setting. If your Kenmore washer isn’t spinning, there are several reasons why this may be happening. ...
  2. Make Sure the Wash Load is Properly Sized and Balanced. When loading your laundry, you should avoid overloading the washer and large items like bed sheets or towels.
  3. Defective Lid Switch Assembly. ...
  4. Worn Out Drive Belt. ...

More items...

How to fix a Kenmore washer that stinks?

  • Combine 1/4 cup of water with 1/4 cup of baking soda; pour into the soap dispenser
  • Pour two cups of white vinegar into your empty washing machine
  • Run a hot wash cycle

How to replace water valve in Kenmore washer?

How to Replace the Water Inlet Valve on a Kenmore Elite

  1. Unplug your Kenmore Elite washing machine. Turn off the water valves supplying water to the washer.
  2. Label the hot and cold water supply hoses with tape before you remove them from the rear of the washer, if necessary.
  3. Remove the cabinet from your top-loading Kenmore Elite. ...
  4. Find the blue water inlet valve attached to the rear panel of your washer. ...

More items...

What would cause a washing machine to not fill up with water?

The hot and cold water hoses that lead to your machine should have a filter screen to catch any large particles that might be coming through the lines. Sometimes these screens can get clogged, which keeps water from flowing properly. This is probably the most common reason for a washer not filling with water.

How do I reset my Kenmore HE top load washer?

If you have started a load in your Kenmore Elite HE washer and need to reset it, simply press several buttons on the control panel.Press the "Stop" button twice, and then press the "Power" button. ... Choose a wash cycle (e.g. "Normal"), and then choose your wash options (e.g. "Hot/Cold" or "Cold/Cold").More items...

How do you run a diagnostic on a Kenmore washer?

1:109:20Kenmore Washer Troubleshooting - How to Find Error Codes ... - YouTubeYouTubeStart of suggested clipEnd of suggested clipFully by all the green lights flashing in unison once you've entered the mode. You can continue toMoreFully by all the green lights flashing in unison once you've entered the mode. You can continue to turn the knob clockwise to enter the different diagnostic modes such as error code mode.

Is there a reset button on a washing machine?

Most newer washing machines come with a reset feature that allows you to restart the washer after it experiences an error code or fault. Causes that lead to these problems include power spikes, imbalanced loads or an interruption in power. Some machines have a button you push to reset its motor.

Common solutions for: Kenmore Washer fills slowly or will not fill at all

The water inlet valve opens to allow water to enter the washing machine. If the water inlet valve is defective, the wash may fill slowly or not fill at all. The water inlet valve requires sufficient water pressure to function properly. First, check the water pressure to determine that it is adequate.

The Right Parts for the Job

We carry more than 4 million parts from over 175 major brands, so chances are, we've got the part you need.

Kenmore Ice Maker is OFF

There are several reasons why your ice maker might not be working. Check to see that the ice maker is plugged in and that there is enough power going to it. Check for any abnormalities in the cord or connection. If you find one, fix it immediately.

Kenmore Ice Maker needs a Reset

Regardless of your familiarity with a Kenmore ice maker, it’s important to know how to fix common issues if they arise. If you’re having trouble with the ice maker freezing or making too many or too few cubes, you can use this ice maker reset factory default button.

Control Arm is in OFF position

The ice maker control arm is located next to the ice bucket. The control arm controls whether the machine is making ice, or not making ice. If the control arm is in the off position, the machine will not fill up with water and it will not make any ice.

Clogged Water Filter

If water isn’t flowing into your Kenmore ice maker, try cleaning the filter. You can clean the filter by rinsing it in warm water to remove debris and make sure that it is free from impurities. If it is not clean, you may have to replace it.

Frozen or Blocked Water Line

If water doesn’t flow out of the water line. You may need to clean out the water line. To do this, remove the back access door and locate the water inlet tube that runs from the icemaker to the customer’s water supply line. Clean out any limescale and calcium deposits with a plastic scouring pad (do not use a metal scouring pad).

Faulty Water Inlet Valve

The water inlet valve is a device that is built into the ice maker to make it function. This can be an electronic or a mechanical part depending on the style of machine you have. If there is no water fill, you may need to replace this part or adjust a setting.

How do washing machines connect to water?

Washing machines are connected to the household water supply by fill hoses. These hoses are typically 4-5 feet in length and often will have a plastic or wire mesh screen inserted into the end of the hose that attaches to the faucet. The screen prevents sediment from entering the water inlet valve, which is located on the back of your appliance.

Where is the water inlet valve on a washing machine?

Before beginning, ensure that you have unplugged your washing machine. The water inlet valve will most likely be found directly behind the hose connections. You will need to remove the rear panel in order to access it. Once you have located it, remove the valve in order to test it.

How to inspect washing machine hoses?

How to inspect the hoses & screens on your washing machine: Before suspecting the hoses & screens, ensure that the faucets are turned on and that the inlet hoses are not kinked. Next, you should turn off the faucets and remove the fill hoses from the inlet valve. Inspect the screens that are part of the inlet valve, remove any debris that you find.

How to test a selector switch on a washing machine?

How to test the selector switch in a washing machine with a multi-meter: Disconnect your appliance from the power source before starting. Open your washer’s cabinet in order to locate and remove the selector switch. It is usually secured to the frame of the appliance.

How to test timer on washing machine?

How to test the timer control in a washing machine with a multi-meter: Before beginning, ensure that you have disconnected your appliance from the power source. Locate and remove the timer. You will need to remove all or part of your washer’s cabinet.

How to change multimeter reading to zero?

With your multi-meter set to Rx1, touch the probes to the terminals of one button, you will be testing one button at a time. Press in on the first button, your reading should change from infinity to zero. Then you should press in on another button, this should change the reading back to zero.

A B C D E F G H I J K L M N O P Q R S T U V W X Y Z 1 2 3 4 5 6 7 8 9