Steps to Install TPS Xiaomi Tool
- Switch off your Xiaomi device -> Press and hold the Power + Volume Down buttons together until the Fastboot logo appears.
- Next, connect your handset to the PC using the USB cable.
- Run the TPS Xiaomi tool on PC and start using it.
- Step 1: Locate the sensor. ...
- Step 2: Disconnect the negative battery cable. ...
- Step 3: Remove the sensor electrical connector. ...
- Step 4: Remove the sensor mounting screws. ...
- Step 1: Install the new sensor. ...
- Step 2: Install the sensor mounting screws.
How to install TPS on Xiaomi phones?
01/05/2016 · Following on from a couple of previous videos covering the testing of these units. This short video covers the instillation and calibration of a new TPS unit...
What is a throttle position sensor (TPS)?
16/11/2010 · Reinstall the throttle body. You will use the new gasket for the intake manifold and the throttle body. Tighten down all the nuts and bolts. Put the two coolant hoses back on, as well. Be sure to plug the connectors into the throttle position sensor and reinstall the cables for the cruise control and throttle. Put the rubber air hose back on.
What happens if the TPS device does not work?
Park your car in your garage or a secure place of work and open the hood of the car. Locate the sensor in most of the cars, it is set up on the butterfly spindle. In clear words, the sensor is located at... The sensor is made of plastic and is usually secured with four screws and bolts. Grab hold ...
How do I install a new temperature sensor on my thermostat?
How to install TPS Xiaomi tool for Windows? You have downloaded the TPS Xiaomi Tool For Windows from the given link. Now, open the folder and install the tool on your PC. The installation process will be blocked if you didn’t disable the antivirus system. You can enable it again after completing the setup. Press the NEXT button again and again.
Can you install a throttle position sensor?
Install the new throttle position sensor. Tighten the mounting screws and attach the electrical connector. Erase the diagnostic trouble code (DTC) with the scan tool using the delete or erase command. Road test your vehicle to see if the check engine light returns.
Does a throttle position sensor need to be programmed?
Code errors can cause your throttle position sensor to work erratically or incorrectly. Otherwise, you'll need professional software to reprogram your sensor. This job is best done by a professional mechanic. If your sensor just needs repairs, it could be the result of faulty or loose wiring.
How much does it cost to install TPS?
Your MechanicWorkWarrantyPriceParts & Labour12 months$106-$245
Do you have to reset computer after replacing throttle position sensor?
After replacing the throttle body to your engine, if the engine light was on and has a pending code, the code will go away. If the code was a hard permanent code, then the ECM (computer) would need a hard reset.28-Dec-2016
How do you reprogram a throttle position sensor?
How to Reset Throttle Position SensorPut the key in the ignition.Turn the key to the On position, without cranking the engine. Wait a few seconds, then turn it off.Repeat the second step.Crank the engine.Pull the parking brake.Set the gear lever in Drive.Wait 5-10 minutes.02-Jun-2021
What happens when you unplug throttle position sensor?
The TPS as we call it is one of the most important sensors on the engine. Without it, the computer has no way of knowing when you push down on the gas or open the throttle. Best it can do it watch some other sensors and make some estimated guesses. On some cars, it may burp just as you unplug it if it's running.
What is difference between throttle body and throttle position sensor?
The TPS checks the amount of air/fuel mixture being delivered to the engine, while the throttle body temperature sensor monitors the temperature of the air/fuel mixture and the actual throttle body.26-Feb-2019
How do you fix a faulty throttle sensor?
Here's How To Replace a Throttle Position SensorDisconnect the Battery. ... Unplug Old Sensor. ... Remove Mounting Screws. ... Remove Old Sensor. ... Mount and Screw In New Sensor. ... Re-Plug Wiring Harness. ... Reconnect Battery Cables. ... Q: I Don't Have Time to Replace My Throttle Position Sensor, Can't I Just Ignore It?More items...•23-Mar-2021
What does the code P0122 mean?
Throttle Position SensorCode P0122 is triggered when your vehicle's Engine Control Module (ECM) detects that your Throttle Position Sensor (TPS) circuit A is reporting an output voltage that is below its expected voltage. Depending on your vehicle, your TPS lower output voltage limit should be around .17-Oct-2018
How do you know when your throttle position sensor is bad?
Your engine might stall, idle slowly or misfire when your car is stopped. The car might accelerate itself, hesitate to accelerate, or lack power when you are trying to accelerate. You may also experience difficulty in changing gears.18-Feb-2021
How do I relearn my throttle body?
1:112:42When Should I Reprogram My Car's Throttle Body? - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou might have to let it run for three minutes and then shut the vehicle off. And then run it againMoreYou might have to let it run for three minutes and then shut the vehicle off. And then run it again for three minutes. It depends on the type of vehicle.
Can you bypass throttle position sensor?
If you disconnect the throttle position sensor - then turn on the ignition and wait for 30 seconds - then start the engine - it should start ok. It takes a while for the ECU to realize that the TPS isn't working and to adjust how it operates. The engine won't work as well without a TPS, but it will work.