The reason your washer will not stop filling could be because the hose has either clogged, fallen off, or gotten a hole in it. If there is a hole in the hose, it will reduce the pressure and cause the water level switch not to shut off power to the water inlet valve
Valve
A valve is a device that regulates, directs or controls the flow of a fluid by opening, closing, or partially obstructing various passageways. Valves are technically fittings, but are usually discussed as a separate category. In an open valve, fluid flows in a direction from higher pressure to lowe…
Full Answer
How do I troubleshoot my insignia washer?
Our comprehensive Insignia Washer Troubleshooting guide will explain common issues, provide tips, and show you how to read your model's error codes. • Make sure that the lid is closed. • Make sure that the water source faucets are open. • Make sure that you press the Start/Pause button to start your washer.
How to fix a washing machine that won’t fill with water?
Sometimes, when a washing machine is pressed too close to the wall, the fill hoses can get squeezed. Make sure to untangle any kinks and eliminate any crimps. Then, close the water supply faucet and unscrew the hose from both ends. This will allow you to examine the hose from the inside.
Why is the water inlet valve on my washing machine not working?
If the switch is defective, it may not supply power to the water inlet valve. Unplug your washing machine. Before suspecting the switch as the issue, inspect the air dome hose by submerging it in water, sealing one end and blowing in the other, no bubbles should come out of the hose during this test.
Why is my Kenmore Elite washer not filling up with water?
If your washer is not filling with either hot or cold water and you have water pressure to the inlet valve, you should next verify that you have power to the solenoid on the valve during the fill portion of the cycle.
Why isn't my washer filling up with water?
0:187:25Washer Won't fill? - Top 5 Problems and Fixes - YouTubeYouTubeStart of suggested clipEnd of suggested clipOne is located in the end of the fill hose. And the other is inside the inlet valve itself if theMoreOne is located in the end of the fill hose. And the other is inside the inlet valve itself if the washer won't fill it could be that the screens are clogged. So take your fill hoses.
How do I reset my insignia washing machine?
1:153:22Insignia Washer Troubleshooting - YouTubeYouTubeStart of suggested clipEnd of suggested clipCheck the fuse or reset the circuit breaker. Close the lid then press the start pause button toMoreCheck the fuse or reset the circuit breaker. Close the lid then press the start pause button to start your washer for your safety your washer does not spin unless the lid is closed.
How do I fix my insignia washing machine?
2:129:37Insignia Washer Complete Repair Guide - Troubleshoot Simple ...YouTubeStart of suggested clipEnd of suggested clipMake sure that both faucets are fully turned on make sure that the water inlet hoses are not kinkedMoreMake sure that both faucets are fully turned on make sure that the water inlet hoses are not kinked straighten if necessary disconnect the hoses. And clean the screens.
Is there a reset button on a washing machine?
Most newer washing machines come with a reset feature that allows you to restart the washer after it experiences an error code or fault. Causes that lead to these problems include power spikes, imbalanced loads or an interruption in power. Some machines have a button you push to reset its motor.
Why won't my washer fill?
One common reason for the failure of a washer to fill is heavy clogging in the filters. First, unplug the washing machine, then disconnect the hoses from the back of the unit. You’ll be able to see the filters on the back of the washer sitting in the water inlet valve.
What to do when your washing machine won't fill?
Screwdrivers. Wrenches. Multimeter. When your washing machine won’t fill with water, you’re going to need to repair any problems immediately. Doing it yourself is a much cheaper proposition than calling in a plumber, and in most instances, it’s a job you can manage yourself with just some basic tools and a little time.
Why won't my washing machine fill?
The reason the washing machine won’t fill might lie with the water level switch. To test this, you’ll need to open up the washer and locate the control panel. BEFORE PROCEEDING YOU HAVE TO MAKE SURE THAT THE WASHER IS UNPLUGGED IN ORDER TO ELIMINATE THE RISK OF ELECTRIC SHOCK. The water level switch is easy to spot since it has a clear tube running to it. You’ll need to test it with your volt-ohm meter. Have it set on RX1 and check all three terminals by trying all the possible pairings with the probe. One pair should give you a zero reading and on all the others, the reading should be infinity. If not, you’ll need to replace the water level switch.
Why is my washing machine hose kinked?
It could also be that the hose is kinked, which would prevent water from passing through, or damaged. If the hose is just kinked, simply straighten the hoses, and try the washing machine again to check that it fills properly. If the hose is damaged, you will need to replace it as soon as possible.
How to inspect washing machine hoses?
How to inspect the hoses & screens on your washing machine: Before suspecting the hoses & screens, ensure that the faucets are turned on and that the inlet hoses are not kinked. Next, you should turn off the faucets and remove the fill hoses from the inlet valve. Inspect the screens that are part of the inlet valve, remove any debris that you find.
Where is the water inlet valve on a washing machine?
Before beginning, ensure that you have unplugged your washing machine. The water inlet valve will most likely be found directly behind the hose connections. You will need to remove the rear panel in order to access it. Once you have located it, remove the valve in order to test it.
How to test a selector switch on a washing machine?
How to test the selector switch in a washing machine with a multi-meter: Disconnect your appliance from the power source before starting. Open your washer’s cabinet in order to locate and remove the selector switch. It is usually secured to the frame of the appliance.
How to test timer on washing machine?
How to test the timer control in a washing machine with a multi-meter: Before beginning, ensure that you have disconnected your appliance from the power source. Locate and remove the timer. You will need to remove all or part of your washer’s cabinet.
How do washing machines connect to water?
Washing machines are connected to the household water supply by fill hoses. These hoses are typically 4-5 feet in length and often will have a plastic or wire mesh screen inserted into the end of the hose that attaches to the faucet. The screen prevents sediment from entering the water inlet valve, which is located on the back of your appliance.
Where is the water level switch located?
It is usually found below the control panel but may also be found below the sump area below the tubs. Inspect the switch for any signs of wear, burning, cracking, or damage. If the air dome hose is not damaged or if your switch shows any the symptoms above, you may need a replacement water level switch. Back to Top.