1 Icemaker IM4D Installation Instructions Hose Clamp Hex-Head Screws, for attaching water tube inlet cover (2) (5/8”)* Hex-Head Screws, for bracket extension (1) (1/4”)* Bracket Extension *NOTE: Screw lengths are the lengths of the threaded portion of the screw, not including the head. INSTALLATION INSTRUCTIONS Icemaker IM4D or Icemaker IM4LED
Full Answer
Can be used in any model accepting an im4d icemaker?
Can be used in any model accepting an IM4D icemaker. The LED lights are activated by a motion sensor when the freezer door is opened. The sensor is located on the front of the icemaker. The LED lights are set to turn off after a period of time if no motion is detected in front of the sensor.
How do I order an im4d or im6d kit?
To order a kit from GE Appliance Parts, you can order the IM4LED by calling 1-877-959-8688 or you can order the IM6D kit: Order the IM6D online For assistance installing the IM4D or IM4LED:
What if my Refrigerator calls for an im5d icemaker?
If the refrigerator calls for an IM5D icemaker (optional second icemaker), use that icemaker kit instead. Refrigerator - IM5D Accessory Icemaker Kit
How do I know if im4d will fit in my Refrigerator?
Make sure this fits by entering your model number. For use in most top-freezer refrigerators and some bottom-freezer refrigerators, please check the label on the back of your refrigerator to ensure compatibility. Quickly install a new or replacement IM4D icemaker unit with an all-inclusive kit.
How do I connect my GE refrigerator ice maker?
1:134:13GE Appliances IM6D Icemaker Installation - YouTubeYouTubeStart of suggested clipEnd of suggested clipNext insert the icemaker power cord plug into the socket by pressing firmly then lock the plug intoMoreNext insert the icemaker power cord plug into the socket by pressing firmly then lock the plug into place by clipping the restraints onto each side of the plug. Now lift the icemaker.
How do I install a new ice maker?
1:242:48How to Install a Refrigerator Ice Maker Kit - YouTubeYouTubeStart of suggested clipEnd of suggested clipPlug. In the icemaker wire harness push the plastic wire harness cover over the plug and snap itMorePlug. In the icemaker wire harness push the plastic wire harness cover over the plug and snap it into place hang. The icemaker on the mounting screws.
Can I add an ice maker to my GE fridge?
Select GE and Profile branded French-Door refrigerators either offer dual icemakers or a second icemaker option. One icemaker is located in the fresh food section, while the second icemaker (included or optional) is located in the freezer.
How do I turn on my GE top freezer ice maker?
0:001:37French Door Refrigerator Icemaker Operation - YouTubeYouTubeStart of suggested clipEnd of suggested clipIf you want to turn the icemaker off tap the icemaker or ice button depending on which modelMoreIf you want to turn the icemaker off tap the icemaker or ice button depending on which model refrigerator you have you may have to hold that button for 3 seconds to activate.
How do you plumb an ice maker?
4:359:43How to install the under counter ice maker - YouTubeYouTubeStart of suggested clipEnd of suggested clipJust make sure you don't go too tight. And you're all set next thing we're going to do is go aheadMoreJust make sure you don't go too tight. And you're all set next thing we're going to do is go ahead and connect the water line that you've already connected to the icemaker.
Do you have to hook up ice maker?
For the ice maker to work, you need to connect it to a water supply. If that is not convenient, then maybe you should look at another model without the ice maker. Otherwise, if the ice maker is not used, you will waste freezer space since you would have to use conventional ice trays.29-Jul-2020
Why is my GE freezer not making ice?
If the water inlet valve is defective, or if it has insufficient pressure, it won't allow water to flow through. As a result, the ice maker won't make ice. The valve requires at least 20 psi to function properly. Make sure that the water pressure to the valve is at least 20 psi.
What is the difference between a single and dual ice maker?
The dual ice maker means there is a dispenser for ice in the door, but there is also a bucket in the freezer drawer that accumulates ice. They work independently of each other. The door dispenser is good for a single cup, and the bucket is good for large amounts of ice for coolers or sports bottles.05-Jul-2016
Why is my GE ice maker not working?
The icemaker must reach a temperature of 16 degrees F before a cycle will begin. If the temperature in the freezer is too warm, ice cubes will take longer to form or may not form at all. Try adjusting the freezer temperature a little lower. A low food load in the freezer can affect the production of ice.
Where is the icemaker switch located?
This type of icemaker is primarily found in Bottom-Freezer and French-Door style refrigerators, though it can be found in other styles as well. To turn ON the icemaker, slide the switch to the left so that the paddle is extended out past the icemaker.
How do you force a GE ice maker to cycle?
Turn on the motor until it reaches home the next time. Turn on the water valve for 1/2 second. Tum on the heater for 1/2 second. Verify that the feeler arm was in the "in" and then in the "out" position.05-Aug-2013
How do I reset my GE refrigerator ice maker?
This arm, also called a feeler, is what tells the unit to stop producing ice when it comes into contact with ice cubes. Restore power to the ice maker. Next, push up on the arm or feeler three times. This will reset the unit.23-Apr-2020
IM4D and IM4LED ICEMAKER ACCESSORY KIT INSTRUCTIONS
49-60698-3 5 BEFORE YOU BEGIN Read these instructions completely and carefully. • IMPORTANT – Save these instructions for local inspector’s use. • IMPORTANT – Observe all governing codes and ordinances. • Note to Installer – Be sure to leave these instructions with the Consumer.
GE Ice Maker Kit for Top Mount Refrigerators IM4D
Producing seven ice cubes per cycle and up to 130 cubes per day, the GE Ice Maker Kit for Top-Mount Refrigerators keeps ice at-the-ready for chilling beverages and filling coolers. The included bucket
GE® Icemaker - IM4D - GE Appliances
GE Appliances is your home for the best kitchen appliances, home products, parts and accessories, and support.
GE Icemaker Kit White IM4D - Best Buy
A: Answer Hi Keith - Yes, GE Profile Arctica Refrigerator PTS25LBM model is compatible with GE® Icemaker IM4D. The IM4D is an accessory icemaker kit that provides everything needed to install a icemaker into most icemaker-ready top freezer and bottom freezer models made since 2001.
About This Product
Connect to WiFi for real-time feedback, optimized performance, alerts and more.
Schedule Service
Our online tools are here 24 hours a day to help you arrange the service you need.
What is an IM4D?
The IM4D is an accessory icemaker kit that provides everything needed to install a icemaker into most icemaker-ready top freezer and bottom freezer models made since 2001*. If you have this kit and want to know if it will work with existing models, please check the label on the back of your refrigerator to ensure compatibility The kit includes the icemaker , bucket, fill tube, water valve, and installation instructions, as well as adapters and powers cords for multiple models.
How does the LED light work on an ice maker?
Can be used in any model accepting an IM4D icemaker. The LED lights are activated by a motion sensor when the freezer door is opened. The sensor is located on the front of the icemaker. The LED lights are set to turn off after a period of time if no motion is detected in front of the sensor.
How to order a GE IM4LED?
To order a kit from GE Appliance Parts, you can order the IM4LED by calling 1-877-959-8688 or you can order the IM6D kit: Order the IM6D online.
When was the IM4LED discontinued?
About the IM4LED. Launched in 2017 and discontinued April 2019 (available until stock is depleted) Same as the IM4D, except that it is also equipped with LED lights to add bright lighting to the freezer. Can be used in any model accepting an IM4D icemaker.
Can you use an IM4D in an SXS refrigerator?
Similar to the IM6D and can be sold in its place. The capacity of the ice bucket is 6 lbs. Cannot be used with SxS refrigerators. Dimensions: 9.5"W x 9.5"H x 14.5"D.
Special offers and product promotions
Create your FREE Amazon Business account to save up to 10% with Business-only prices and free shipping.
Have a question?
There was a problem completing your request. Please try your search again later.
Top reviews from the United States
There was a problem filtering reviews right now. Please try again later.
Delivery and Installation
This video will walk you through the simple steps you must take in order to ensure a successful delivery and installation of your new Refrigerator from The Home Depot.
Product Overview
Producing seven ice cubes per cycle and up to 130 cubes per day, the GE Ice Maker Kit for Top-Mount Refrigerators keeps ice at-the-ready for chilling beverages and filling coolers. The included bucket holds up to 5 lbs. of ice while the ice maker churns out up to 3 lbs. per day.
Info & Guides
You will need Adobe® Acrobat® Reader to view PDF documents. Download a free copy from the Adobe Web site.