Full Answer
What is the rear end width of a Ford Mustang?
16/01/2020 · You can identify the Ford 8.8-inch rear by its rear cover. It has a thin metal or plastic 10-bolt cover, and the bolts are 7/16-inch thread. The cover is not quite square, measuring about 101/2 inches high by 11 inches long. The 8.8-inch pinion shaft is 15/8 inches and has 30 splines.
What is the rear end width of a Ford Ranger?
The 1986-1988 (chassis cab) 8.8-Inch axles are distinctive as they are the only 8.8-Inch Ranger rears that have no provisions for a RABS sensor. Ranger 4.0L Models: The Ford 8.8-Inch axle began regular use in the Ford Ranger starting with the 1990 4.0L models. All 4.0L Ford Rangers are equipped with 8.8-Inch axles.
What size is the rear end on a Ford 9 axle?
04/07/2017 · Outside Width: Year: Model: 56.50: 1969-1977: Maverick 8" 56.50: 1990-1992: Ford Ranger 8.8" 56.75: 1995-2003: Ford Explorer 8.8" Narrowed w/2 short side axles: 57.00
What are the parts of a Ford 8 8 axle?
26/06/2020 · The gears are all the same for Ford 8.8s. The carriers usually come in two different sizes, depending on gear ratio. Additionally, how strong is a Ford 8.8 rear end? Another strength consideration is pinion-shaft diameter. Here, the 8.8 and the 12-bolt are identical at 1.625 inches and in fact use the same pinion bearings.
How wide is a Ford 8.8 differential?
Gear ratios depend on the year and model of the Ford vehicle. The ring gear measures 8.8 inches in diameter with the single-piece case bolted with 10 7/16X20-inch threaded bolts. The pinion gear measures 1.626 inches in diameter with a 28-spline axle shaft through 2001, and 31 splines beginning in 2002.
How wide is an 8.8 Ford rear end?
How To Spot, Build, And Swap In the Ford 8.8 Mustang Rearend.Vehicle ApplicationAxle Width (inches)'86-'93 Ford Mustang 8.859 11/44FORD'65-'66 Mustang57 11/44'67-'70 Mustang 8.059 51/488 more rows•17-Jan-2008
What is the narrowest Ford 8.8 rear end?
The Explorer 8.8 is narrowed by cutting out 2.875 inches from the driver's side axle tube, welding it back together, and installing a separate passenger side axle in the now shortened driver's side axle tube.25-Jul-2015
How wide is a Ford 9 inch rear end?
The 9” rear axle was manufactured in seven different housing widths, from 57-1/4” to 69-1/4” wide, any of which may be ideal for a particular chassis.
How much power can a Ford 8.8 rear end handle?
Dead stock (31 spline version, which is what the Explorer has) it can handle up to about 400 rwhp as long as you're not on DR's or Slicks. As soon as you go to those, you have to weld the tubes at a minimum.15-Nov-2006
How do you tell the difference between a Ford 8.8 and 9?
There's an easy way to tell an 8-inch apart from a 9-inch. All of the 8-inch case nuts can be accessed with a socket. In contrast, on the 9-inch, two nuts on the bottom at about the 6 and 7 o'clock positions cannot be accessed with a socket and require a wrench.
How do I identify a Ford 8.8 rear end?
You can identify the Ford 8.8-inch rear by its rear cover. It has a thin metal or plastic 10-bolt cover, and the bolts are 7/16-inch thread. The cover is not quite square, measuring about 101/2 inches high by 11 inches long. The 8.8-inch pinion shaft is 15/8 inches and has 30 splines.
How do you measure a Ford 8.8 axle?
This is simply the make and model of the rear end you are working on. Examples of this is GM 12 Bolt, Mopar 9 1/4, Ford 8.8, etc... This should be measured with a tape measure by hooking the outside of the axle flange (wheel side-where the wheel studs are) and pulling back to the end of the C-Clip Button.
Are all 8.8 gears the same?
Moderator Emeritus The gears are all the same for Ford 8.8s. The carriers usually come in two different sizes, depending on gear ratio. The spider gears must match your axle spline count as that's where they attach to the carrier.07-Aug-2003
What Ford has a 9 inch rear end?
The 1969-'77 full-size Ford, Mercury, Lincoln, and half-ton trucks from 1973-'86 used the strongest (thickest tubing) rear housing of all the 9-inch rear donors. These cars and pickups are where you'll likely find a donor differential that has the 31-spline axle configuration.
How do you measure a rear end width?
How to Measure Rear End WidthLocate the axle flanges on either side of the rear axle. The flange is the platform on which the wheels are mounted and bolted to the axle.Using a measuring tape, measure from one flange to the other.
How do I identify a Ford 9-inch rear end?
0:053:07How to tell the difference between a Ford 9 inch and an 8 inch rear end ...YouTubeStart of suggested clipEnd of suggested clipBetween the 48 inch rear end and the Ford nine-inch rear end both look very similar one's a littleMoreBetween the 48 inch rear end and the Ford nine-inch rear end both look very similar one's a little bit bigger the 9 inch is a little bigger.
What is 8.8 axle?
Ford 8.8 - Disc Brakes. The Ford Explorer 8.8-Inch rear axle has found homes in numerous vehicles besides the Explorer. It has been swapped in to Ford Rangers, Bronco II's, Jeeps, Chevy S-10's and even some cars. The 8.8-Inch axle used in the Explorer is highly desirable because it came with 31-spline axles over the typical 28-spline found in ...
How far apart are Rangers axle pads?
The Rangers axle spring pads are spaced 38-1/2 inches from center to center with a 3/4-inch hole in the center for the blocks locating pin. You will need larger u-bolts to fit around the 8.8's larger 3-1/4 inch axle tube.
What size brakes did the Explorer have in 1994?
Brakes: The 1990-1994 Explorer 8.8-inch axle came with 10-inch drum brakes. 1995 and newer Explorers have disc brakes. People have reported that they have swapped in a newer disc brake 8.8-inch axle in place of their original drum brake axle without having to switch to a disc brake master cylinder.
How wide is a Ranger 8.8?
You can buy spring pads from most off-road shops. The 8.8 is 3-1/4 inches in diameter and the Ranger uses a 2-1/2 inch wide spring pad.
When did the 7.5 axle come with disc brakes?
In 1995 the axles came with disk brakes. My axle still had the drums, however, they're an inch larger in diameter than the 7.5's with much bigger brake shoes. I completely stripped all of the brake components from the backing plates and started with all new parts.
