To enter diagnostic mode, follow the tutorials below:
- Turn on the device.
- Continuously press the END/DELAY key until the number 17 appears on the screen.
- Press and hold the START key for about 7 up to 10 seconds.
- If AS codes on the screen show that the Samsung top load washer is in diagnostic mode.
Why won’t my Samsung top load washer spin?
Samsung top load washers are reliable and easy to use, but they can still fail to spin. This is often caused by an overloaded drum, but Samsung top load washers won’t spin if there’s a mechanical failure either.
Are there any Samsung front load washers that have been recalled?
There has been a recall on Samsung front load washers because water leakage onto the electrical connections of the washing machine's thermal sensor could cause an electrical short and ignite a circuit board, posing a fire hazard to consumers.
How do I clear error codes on my Samsung washing machine?
To clear any error codes from your washer display panel, you’ll need to reset the machine. Just disconnect the washing machine by unplugging it from the wall outlet or turning off the washroom breaker. After 5 to 10 minutes, reconnect the power and run a test wash load to confirm the code has cleared. What Does “UR” Mean On A Samsung Washer?
How do I adjust the cycle on my Samsung washing machine?
The machine may adjust the washer cycle by water volume, adjusted water temperature, or an extra spin cycle where needed. It’s always a good idea to check the labels in your wash items to determine the most effective cycle. How do I reset my Samsung top load washing machine?
How do I run a diagnostic test on my Samsung washer?
2:145:00Samsung washer - How to enter into Diagnostic Mode - Error CodesYouTubeStart of suggested clipEnd of suggested clipPress and hold Start for 7 to 10 seconds. It will come up with a s. At this point just press Start.MorePress and hold Start for 7 to 10 seconds. It will come up with a s. At this point just press Start. And it's going to start your test cycle.
How do you put a washing machine in self test diagnostic mode?
0:000:48Whirlpool Washer Test/Diagnostic Mode - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou press the start button this will allow your washing machine to go into the test or diagnosticMoreYou press the start button this will allow your washing machine to go into the test or diagnostic mode and this will isolate if you're having any issues the water will run the spin cycle will engage.
How do you troubleshoot a Samsung top load washer?
0:513:02Samsung Top Load Washing Machine: How to Troubleshoot ... - YouTubeYouTubeStart of suggested clipEnd of suggested clipCheck the inlet holes filter. The machine may not get enough water if inlet hose is twisted kinkedMoreCheck the inlet holes filter. The machine may not get enough water if inlet hose is twisted kinked or blocked therefore it is advised to check the condition of the pipe.
How do I reprogram my Samsung washing machine?
Resetting your washing machine is a simple procedure. Unplug it (or turn off the power at the circuit breaker), wait a short period of time for the electrical charge to dissipate from the washer (typically 1 to 5 minutes at the most), and then plug it back into the wall. That's all there is to it.
What is diagnostic mode on washing machine?
The washer's diagnostic mode can be used to troubleshoot washer problems by viewing logged washer errors, performing an automatic diagnostic cycle, or manually turning on and off different washer parts to test for proper operation.
How do I put my GE top load washer in diagnostic mode?
0:236:05How to Find Error Codes, and Reset a GE Washer - YouTubeYouTubeStart of suggested clipEnd of suggested clipOnce this is done let's go ahead and start with this code first press and hold the start button onMoreOnce this is done let's go ahead and start with this code first press and hold the start button on the washing. Machine and once this is done turn the main dial counterclockwise or to the left.
What are the codes on a Samsung washer?
Samsung Front-Load Washer Error CodesFault CodeWasher ProblemLELow water level during cyclesOEOverflow or too high water levelsnF1Hot and cold water lines are reversedtEWater temperature is either too high or too low13 more rows•Apr 14, 2022
Why is my Samsung washing machine not draining or spinning?
If your washer doesn't drain or spin: Make sure the drain hose is straightened. If you have a kink in the hose, it may restrict any water from draining. Make sure the debris filter is not clogged. If you are able to open and close the door, close it and press START/PAUSE.
What is the average life of a Samsung washing machine?
It is typically recommended to replace any large appliance, such as a washing machine, every eight years, but your washing machine could potentially last up to 14 years with proper upkeep and maintenance.
How do you reset a Samsung?
How to perform Factory Reset on Android smartphone?Tap Apps.Tap Settings.Tap Backup and reset.Tap Factory data reset.Tap Reset Device.Tap Erase Everything.
How do you reset an automatic washing machine?
1:243:47Washer Not Spinning - How to Reset Motor (Easy) - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe machine gives you 30 seconds to lift the lid and close. It six times and once you start liftingMoreThe machine gives you 30 seconds to lift the lid and close. It six times and once you start lifting the lid. You have 12 seconds to do the six repetitions.
Samsung Water Pump Issue During Spin Cycle
Problem: During the spin cycle, the washer pump keeps trying to pump water out disrupting the spin cycle.If this problem happens, it's time to do a...
Bleach Spotting After Every Use
Problem: After adding bleach in the bleach dispenser to clean and disinfect the washer or a load of clothes, bleach spotting occurs on future loads...
Samsung Washer Trips Electrical Circuit
Problem: Washer trips the electrical circuit in the home when it is turned on. There has been a recall on Samsung front load washers because water...
Water Remains in Detergent Dispenser After Every Wash
Problem: After every load of laundry, water remains in the detergent dispenser tray. It is not unusual for water to be left in a detergent, bleach,...
Purple Streaks Left on Fabrics
Problem: Purple streaks appear on clothes after a cold water, short cycle wash.The purple streaks happen when too much laundry detergent is used. O...
Washer Leaking During Rinse Cycle
Problem: Washer leaks water during the rinse cycle even after cleaning the lint trap and checking water and hoses for leaks.If a leak is going to h...
Washer Stops During Spin Cycle
Problem: Washer stops during spin cycle and becomes off-balance. Spin cycle will complete after clothes are rearranged. To solve the problem: 1. Ru...
Samsung Washer Will Not Start
Problem: Washer will not start even though the display says it is ready to begin the cycle. If the washer is receiving electrical power and everyth...
What is the test mode on a Samsung washing machine?
The test mode of the Samsung washing machine, provided by the manufacturer of household appliances, allows you to start the unit's self-diagnosis system. Such an opportunity will help the user to check the operability of all elements of the device, to identify existing failures and shortcomings without opening the machine body. How to start a service test, we will describe further.
What is a service test on a washing machine?
The service test will tell you where to look for the main reason for the failure of the washing machine, be it problems with the inlet or drain hose, problems with the SMA motor, water level sensor or main board.
How to test Eco Bubble Pump?
One press on the Spin key allows you to test the serviceability of the drain hose. The second is to turn on the Eco Bubble pump. A third press will turn off the pump. If you are sure that there are no problems with draining the water from the drum, proceed directly to the Eco Bubble pump, for this you should quickly, twice in a row, press the button responsible for spinning. Now look through the hatch door. In the water with which the drum is filled, bubbles should begin to appear, this indicates that the bubble wash function is functioning properly.
How to check if a heater is working?
The “Options” button will help you to check how the heater works. By pressing the key, you turn on the heating element for a few seconds. If no changes occur on the control panel of the machine, then the heater is in good condition. If there are any problems with the heater, the device will give an error on the heating element.
What does the spin mode on a water level sensor mean?
Setting the selector to the "Spin" mode will display on the digital display of the machine the current frequency of the signal of the water level sensor in the tank. For example, flashing 24.16 symbols on the screen will indicate that the frequency signal of the sensor is 24.16 kHz.You can check how this value changes on the drain, the frequency should increase by about 2 kHz.
How to check water temperature in a washing machine?
By clicking on it, you can observe how the tank begins to fill with water through the first section of the detergent dispenser. When the “Temperature” key is pressed again, water will be supplied through the second section of the tray. This will check both filler compartments. A third press will turn off the fluid in the drum.
What is service test on Samsung?
The service test of the Samsung machine is conventionally divided into two stages, and the first of them is the verification of the linear components of the machine. It allows you to visually verify the sufficient performance of linear components, such as:
Why do Samsung washers have out of balance protection?
Today's washers have out of balance protection installed to protect a washer from damaging itself during the spin cycle. Some Samsung washers add more water during the spin cycle to attempt to correct the imbalance of a small load. To solve the problem of extra water, redistribute the clothes to better balance the washer.
How to fix slow drain on washer?
To correct the slow drain, open the bottom panel of the washer housing. You will see a plug on the lower right. Have some towels ready to catch a gush of water and remove the plug. Clean out the filter. You may find lint, coins or buttons are obstructing the flow into the pump. Never overload the washer.
How to prevent drips from bleach dispenser?
After using the bleach dispenser, remove the dispenser cup and rinse it well or dry it with a paper towel to prevent drips.
What happens if the washer is not level?
If the washer is not level and it is tilting to one side or forward or backward, the dispenser cups will not empty completely and you will get drips on the next load. After using the bleach dispenser, remove the dispenser cup and rinse it well or dry it with a paper towel to prevent drips.
Why does my washer have purple streaks?
Solution: The purple streaks happen when too much laundry detergent is used. One teaspoon of concentrated HE detergent is the recommended amount for a small, cold water load. Never use more than two teaspoons in a HE washer no matter the load size or water temperature.
Why does my front loader leak?
Solution: If a leak is going to happen with a front loader, it is most often during the rinse cycle because more water is used at that time. The cause is most likely a leak or hole in one of the interior lines. It could be a puncture/hole in either the drain hose or the soft, black bellows hose next to the drain pump assembly. If you need a user or repair manual, you can find it here .
Can you overload a washer?
Never overload the washer. Take time to read the manual when you are not in a hurry to learn which cycle to select for different size loads.
How to calibrate a washing machine?
Step 1. Remove all laundry or any other contents in the machine. Step 2. Power off, and then power on the washing machine on again. Step 3. Hold down Temp. and Delay End (+) simultaneously for 3 seconds to enter Calibration mode. (The Cb message appears on the display.) Step 4.
How to calibrate a lower washer?
To calibrate the lower washer. Step 1. Remove all laundry or any other contents in the machine. Step 2. Press POWER on the control panel of the lower washer to turn the washer on. Step 3. Press and hold Temp. and Delay End on the lower washer control panel simultaneously for 3 seconds.
When to run calibration mode on washing machine?
It is recommended to run the calibration mode before starting a wash after your washing machine has been installed or moved.
How to calibrate a pulsator?
Step 2. Press and hold Temp. and Delay End simultaneously for at least 3 seconds when the power is turned on. Step 3. Press and hold START/PAUSE to activate Calibration Mode. Step 4. The pulsator rotates clockwise and counterclockwise for approximately 1 minute. Step 5.
Why add test cycle after product installation?
Note: Add the test cycle to make sure that it is installed well after the product installation (applicable models only).
Does Samsung washing machine detect laundry weight?
Your Samsung washing machine detects the laundry weight automatically. This helps the product balance and improve performance. For more accurate weight detection, please run the calibration mode after the installation.
How to remove the lid switch from a washer?
Remove the console cover assembly and lift the cover off the washer. Next, disconnect the lid switch wire from its harness, then remove the screws from the top panel. Lift the lid and prop it securely onto the wood plank.
How to tell if washer isn't spinning?
Have you ever gone to put your clothes in the dryer and found soaking wet clothes in the washer? Aggravating, isn’t it? That’s usually the first sign that your washer isn’t spinning properly.
How to fix a washer that won't spin?
This is the easiest error to fix: just open the lid and redistribute the clothes inside the wash drum. Once you close the lid again, your washer should spin.
What happens if the lock on the washer doesn't work?
If the lock isn’t working, the control board “reads” the lid as open and won’t spin the wash load. If the lid switch assembly fails, you’ll need to replace it. You’ll need a multimeter to test the lid switch–replace the switch if it doesn’t have continuity.
Why does my washing machine stop spinning?
Too many clothes or heavy items can throw the washload off-balance, causing the spin cycle to stop. The spin cycle can also stop if the wash drum doesn’t drain completely. Other causes could be a faulty lid switch, motor fault, or improper draining.
What happens when you put too many items in the wash drum?
When you put heavy items or too many items into the wash drum, the clothes can shift to one side. This will throw the wash drum off balance and stop the spin cycle.
Why won't my washer spin?
If you’ve balanced the load and the drum still won’t spin, you may have a problem with the suspension. There are usually four suspension rods that stabilize the drum inside the washer housing.
How to turn on a dryer?
Press POWER to turn the dryer on and within 5 seconds, press and hold Adjust Time Up + Dry Level until InS or In appears on the display.
Where is the thermal fuse located on a dryer?
The thermal fuse is a safety device designed to protect the dryer from overheating. The fuse is located on the blower housing or at the dryer's heat source such as the heating element on electric drye If overheated the fuse will have no continuity meaning the electrical path is broken and the fuse has blown.
Is Samsung dryer reliable?
Samsung dryers are generally reliable, but when something goes wrong it can bring your entire laundry routine to a grinding halt. Samsung dryer problems might include a faulty heating element or a broken drum spider. Maybe you don't even know what that is, but you will by the time you're done replacing it. Moreover, how do I find the error code on ...