What does the throttle position sensor do on a Chevy Silverado?
28/03/2020 · Also, how do I reset my electronic throttle body? Turn the ignition switch on and wait 3 seconds. Immediately after the 3 seconds, the accelerator pedal must be pressed and released 5 times within 5 seconds. Wait 7 seconds and fully press the accelerator pedal and hold for approximately 20 seconds until the check engine light stops blinking and stays on.
How to program a throttle position sensor?
10/05/2021 · How to do throttle body Relearn on a Silverado? If you look up “throttle body relearn” for your make and model you should find the process for your vehicle. Mine was basically turn the key on, turn the key off 5 seconds, turn the key on for 5 seconds, turn the key off for 15 seconds, turn it on for 15 seconds, turn it off and start the truck.
How many miles do you have to replace a throttle sensor?
How to Replace TPS Throttle Position Sensor 00-06 Chevy Silverado. step 1: Removing the Throttle Position Sensor (TPS) (0:20) Unclip and disconnect the wiring harness. Remove the two T20 Torx screws from the sensor. Remove the sensor. step 2: Installing the TPS Sensor (2:23) Line up the keyway on the sensor with the keyway on the throttle body. Press the sensor to the …
What does TPS stand for on a Chevy Silverado?
10/06/2015 · i just replaced the tps on my 09 silverado and was wondering is there a procedure to reset the sensor so the computer can recnogize the new part ... 11273B - SPECIAL COVERAGE ADJUSTMENT - THROTTLE POSITION SENSOR. REPLACEMENT. SERVICE CAMPAIGN BULLETIN. Reference Number(s): 11273B, Date of Issue: December 16, 2013. Affected. Model(s): 2008 …
How do I reset my Chevy throttle body?
Fully depress the accelerator pedal for 10 seconds. At this point the check engine light should change to blinking slowly indicating “Erasing ECU Memory”. 8. Release the accelerator pedal and turn the ignition switch to off.
How do I relearn my throttle body?
1:112:42When Should I Reprogram My Car's Throttle Body? - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou might have to let it run for three minutes and then shut the vehicle off. And then run it againMoreYou might have to let it run for three minutes and then shut the vehicle off. And then run it again for three minutes. It depends on the type of vehicle.
Do you have to reset computer after replacing throttle position sensor?
After replacing the throttle body to your engine, if the engine light was on and has a pending code, the code will go away. If the code was a hard permanent code, then the ECM (computer) would need a hard reset.28-Dec-2016
How do I reset my GM electronic throttle control manually?
Resetting your electronic throttle control manually can be a tricky job. First, make sure the accelerator pedal is fully released. Next, turn the ignition on and then turn it off and wait for ten seconds. During these ten seconds, be sure the throttle valve is moving by listening for a sound of operation.
How do you calibrate a throttle position sensor?
1:544:19How to replace / calibrate your throttle position sensor TPS (Honda)YouTubeStart of suggested clipEnd of suggested clipYeah you need a multimeter to do so the negative feed of the multimeter. Should be connected to theMoreYeah you need a multimeter to do so the negative feed of the multimeter. Should be connected to the negative lead of the battery. And the positive lead should be connected to the little red wire.
How do you adjust the throttle position sensor on a Chevy?
0:573:47TPS or Throttle Position Sensor Adjustment 1 - YouTubeYouTubeStart of suggested clipEnd of suggested clipBy simply closing or plugging the idle control valve adjusting the throttle screw for a minimum idleMoreBy simply closing or plugging the idle control valve adjusting the throttle screw for a minimum idle speed. And then readjusting the TPS. The desired idle condition can always be met by the engine.TPS or Throttle Position Sensor Adjustment 1 - YouTubehttps://www.youtube.com › watchhttps://www.youtube.com › watch
How do you reset the throttle position sensor on a GMC?
0:322:05GM Truck Electronic Throttle Body (ETB) Relearn Procedure - YouTubeYouTubeStart of suggested clipEnd of suggested clipNext turn the ignition off for 60 seconds. Then start and idle the engine in Park for 3 minutesMoreNext turn the ignition off for 60 seconds. Then start and idle the engine in Park for 3 minutes again after the 3 minute runtime the engine should be idling normally.GM Truck Electronic Throttle Body (ETB) Relearn Procedure - YouTubehttps://www.youtube.com › watchhttps://www.youtube.com › watch
What happens when you unplug throttle position sensor?
The TPS as we call it is one of the most important sensors on the engine. Without it, the computer has no way of knowing when you push down on the gas or open the throttle. Best it can do it watch some other sensors and make some estimated guesses. On some cars, it may burp just as you unplug it if it's running.What happens when you unplug a throttle position sensor? - Quorahttps://www.quora.com › What-happens-when-you-unplu...https://www.quora.com › What-happens-when-you-unplu...
Sign up for FREE! Become a GM-Trucks.com Member Today!
In 20 seconds you can become part of the worlds largest and oldest community discussing General Motors, Chevrolet and GMC branded pickups, crossovers, and SUVs. From buying research to owner support, join 1.5 MILLION GM Truck Enthusiasts every month who use GM-Trucks.com as a daily part of their ownership experience.
Duelin
all the codes that i recieved was pointing at the sensor so thats why i replaced it. and how it does not make sense to ask if theses a way to reset the computer?
Jsdirt
Good to see the price has finally come down. Back when I was having issues they couldn't be found under $400.
How to program a throttle in a car?
First step calibrating or programing your car throttle is to sit in your car and form the accelerator pedal released position learning. Do not depress the accelerator pedal when you turn the keys on wait for at least 2 seconds for each action. You need to know that the timing of this is important. So when you positioned yourself ready ...
How to program throttle position sensor?
Steps on How to Program a Throttle Position Sensor for a Throttle Valve Closed Position Learning. Step 1. Start by forming the throttle valve closed potion leaning. Step 2. Be sure that the accelerator pedal is totally freed or released. Step 3. Then grab the keys and turn “ON” the ignition switch. Wait 10 seconds.
How to release the accelerator pedal?
Step 1. Make that the accelerator pedal is completely released or free, then turn “ ON” ignition switch and wait for 3 seconds. Step 2. You want completely depress the accelerator pedal very hard and fully release the accelerator pedal as quickly as possible 5 times within 5 seconds.
Step 1 – Open hood and pop off plastic engine cover
That behemoth of a top cover on your Vortec V8 is held on by only two tabs. Gently lift the front until it pops up from its post, then reach under and toward the rear of the cover to pop the back tab. (It's so easy, a US Congressman could do it!)
Step 3 – Remove air intake tubing
At each end of the intake tubing, you'll see a worm-drive clamp. Loosen both clamps at the air cleaner and TB unit. There will also be a tab at the far left side rear. Simply pop that off. Finally, unplug the sensor plug on the intake tube.
Step 4 – Remove power leads to the throttle body
Simply push down on the gray clip tab, and remove the entire plug. You should not have to remove the pink clip.
Step 5 – Remove the throttle body assembly
Using a 10mm wrench, remove the two nuts and two bolts. Then, slide the TB off the studs.
Step 6 – Inspect O-ring and replace if needed
The O-ring should be intact; however, if it has any cuts, abrasions, or is just plain grungy, you should have a new gasket in the new throttle body kit.
Step 7 – Install the new (or refurbished) throttle body
Simply line up the stud screws and slide the unit in place. Tighten the nuts and lower bolts in a crisscross pattern until tight. Do not over tighten! There is no torque spec for these, so use common sense when tightening. Plug the sensor plug in, and secure it with the gray clip.
Step 8 – Reinstall air intake assembly and cover
Install the plastic air intake tubing assembly, tighten the worm-drive clamps, and push the PCV valve back in place. Simply line up the front and rear tabs on the engine cover. Then, push down firmly until it snaps into place. Plug in the sensor at the air cleaner end of the intake.