Receiving Helpdesk

how to make washer boards

by Delphine Leffler DDS Published 3 years ago Updated 3 years ago

How to Build 3 Hole Washer Boards:

  • Cut wood for the frame Cut your 2×4’s for the frame – You’ll need 4 that are 48 inches long and 4 that are 13 inches long. ...
  • Cut the rest of the wood Cut your sheet of plywood for the surface. You’ll need 2 pieces that are 16 inches by 48 inches. ...
  • Next, lay two of your longer pieces of 2x4s and two of the shorter pieces on top of one of your plywood pieces to form a box shape. ...
  • Add the wood screws Use your 3-inch wood screws to attach the the 2×4’s to form the frame. ...
  • Screw the top frame Slide your plywood out from under the frame and place on top. ...
  • Make your 2nd box Repeat steps 3-5 to make the second box.
  • Mark for your holes Take your boxes and find the center (8 inches from the side) and draw a line down the middle. ...
  • Cut your holes At each mark, use your drill and hole saw to cut a hole (you should have three total holes on each box in a straight line).
  • Optional: Add rope Adding the rope is optional, but does help keep the throwing distance consistent and saves time in setting up the game. ...
  • Tie the optional rope Set the the boards 10′ apart, with the eye bolts facing each other. Tie the rope to the eye bolts of both boards.
  • Optional: Finish the boards Finish the surface by sanding down the edges to remove splinters and rough spots. ...

I use scrap wood I found laying around as the plywood support one side friend using wood glue andMoreI use scrap wood I found laying around as the plywood support one side friend using wood glue and screws to secure every piece cut 1 by 3s can also work for this.

Full Answer

How to make 3 hole washer boards?

Step 3: Step Two

  • cut the cheap 1"x2" to around 2" chunks
  • align the 4" pipe with the hole on the plywood
  • with wood glue, use three 1"x2" chunks and secure them around the ABS with a brad nail gun or staples
  • do this for all of the holes
  • attach the 3" board to the bottom of the 2"x4" framecarefully, using 1 1/8" screws, secure the plywood to the 2"x4" frame

More items...

How to build a table over a washer?

Laundry folding table over your washer and dryer. To build this, you will need two sheets of 4′ x 8′ x ¾” plywood. Cuts: (1) 30″ x 86″ for the counter. (3) 29″ x 41 ¼” for the sides. (2) 26 ¼” x 18″ for the shelves. (1) 4″ x 86″ for the counter back (I pieced together scrap ply to make this)

How to make your own rubber washers?

Tools:

  • Metal Lathe
  • Single-edge razor blade (preferable new), a utility knife blade would be effective as well
  • Locking Pliers (Vice-Grips®), small-type

What size are washer boards?

Step 1: The Goods

  • 24 feet of 2x4
  • 45 inches of 3/4"x3"
  • sheet of plywood cut to 16"x48" (two of these)
  • 4" ABS pipe
  • outdoor carpet
  • eye screws or tie down rings
  • rope or chain
  • 3" drywall screws
  • 1 1/8" drywall screws
  • spray adhesive

More items...

What are the dimensions of washer boards?

Regulation board size is 12 inches wide by 48 inches long. However, there are variations available out there that range in size from 12″ wide by 32″ long to 16″ wide by 48″ long. Our preference is for 16″x48″, which is what these directions are based on.

What kind of carpet do you use for washer boards?

Use Astro Turf, or basically really thin outdoor carpet to cover each washer box. The carpet can be applied with 3M Spray Adhesive. This will keep the washers from sliding and bouncing as much.

How do you make your own washer?

0:422:13They did is he took a penny put it in the drill press of ice. Came down drilled a hole through it.MoreThey did is he took a penny put it in the drill press of ice. Came down drilled a hole through it. Put his little bolt through it or his lag bolt here. Looks like a sheet metal screw drill it anyway.

What size washer do you use for washer boards?

Two sets of three standard 3" washers are required and each set must be of a different color or somehow marked differently. Contestants may use their own washers as long as each washer is at least 2 15/16" in diameter and weighs 4 1/2 ounces or less.

How do you make a 3 hole washer board?

0:103:31Take the plywood and cut it to forty six and three-quarter inches long and 14 and three-quarterMoreTake the plywood and cut it to forty six and three-quarter inches long and 14 and three-quarter inches wide because the one by fours are going to bring the outside of the.

What are the dimensions of a 3 hole washer board?

Technical DetailsItem Package Dimensions L x W x H‎32 x 12 x 5 inchesItem Dimensions LxWxH‎32 x 12 x 5 inchesBrand Name‎PIPROXWarranty Description‎NoModel Name‎PIPROX3 more rows

How far apart should washer boards be?

about 20 feet apartWasher boards and boxes are typically positioned on flat surfaces about 20 feet apart. If you would like to give yourself and your friends more of a challenge, you can space them out even farther. Washer toss can be played in teams of one or two players.

How do you make a single hole washer board?

0:394:30Cut two pieces of 3/4 inch plywood. You can also use half inch plywood that would work if that's allMoreCut two pieces of 3/4 inch plywood. You can also use half inch plywood that would work if that's all you have my plywood is 16 inches square find and mark the center of the plywood squares.

What size are washer toss boxes?

16 by 16 by 4 inchesWasher pits and boxes vary in size and shape, but a standard for one-hole washers is 16 by 16 by 4 inches (410 mm × 410 mm × 100 mm), with a cylindrically-shaped cup ( 41⁄2 in [110 mm] in diameter and 5 in [130 mm] in height) located in its upper surface.

How do I make a hillbilly horseshoe?

0:058:34First thing I'm going to do to create the washer board is to get a sheet of OSB plywood you couldMoreFirst thing I'm going to do to create the washer board is to get a sheet of OSB plywood you could probably get by with a half of a sheet. But. It's pretty inexpensive. So I just bought a whole sheet.

How do you keep score in a 3 hole washer?

Keeping Score: One point is scored for the hole closest to the front of the board. Three points are scored for the center hole. Five points are scored for the last hole on the board.

How do you pitch a washer?

0:193:42One in the holes five points a winner over the holes three points and for its closest washer with inMoreOne in the holes five points a winner over the holes three points and for its closest washer with in the foot is one point and if you have your washer in the cup.

How to make a sandbox?

1. Gather your materials. Head to your local hardware store for two 6-ft two-by-fours, two 17-by-17-inch squares of plywood, two 14-by-14-inch squares of carpet (or fake grass) and two 3.5-inch pieces of PVC pipe, each with a 4-inch diameter.

How to play a board game outdoors?

Because the game is usually played outdoors, make sure you create a durable box able to withstand the elements as well as the pounding from the game itself. If you will be playing at a specific location, make sure to measure the dimensions to create a suitable board.

How to make a square frame?

Screw the square frame together. Make sure the wood screws you use are long enough to pierce both pieces of two-by-four at each corner. Use a power drill to ensure that the ends are firmly locked together. Measure and cut a piece of square plywood. Create the square piece of plywood to fit beneath the square frame.

How to make a square out of two by four?

2. Cut four pieces of two-by-four to create a square. Cut each two-by-four to 17 inches in length. Create a 17-by-17-inch square by cutting the ends of each of these four two-by-fours at 45-degree angles with a miter saw or box saw.

How do I install a two by four frame?

Simply flip the nicer side of the frame downwards (if applicable), place the plywood on top, and screw down through the plywood into the two-by-fours. Make sure your screws aren’t too short for the plywood or too long for the two-by-fours. ...

How many points do you get in a washer board game?

Here are some basic rules for playing three-hole washer board game: If you get your washer in the hole closest to you, you’ll get one point. The middle hole is worth three points and the hole farthest from you is five points.

How many washers per player?

Basically, the board consists of four holes close to each corner of the board with one hole in the middle. You’ll need to use six washers per player.

How many washers do you need to throw in a round of golf?

The first player throws both of them, one at a time. The scoring is determined by the proximity of the washer to the cup. Only one player can score per round.

How far apart should you measure a washer pit?

Washer pit distance. The distance between the two pits is completely up to you. Most players recommend that you measure a distance of 25 ’ from the center of one cup to the center of the other. Of course, the greater the distance, the more difficult the game.

How many bags are in a pitcher box?

The same rules apply as for the singles play and each player has 4 bags to pitch. Official rules for playing washers state that the player must pitch with the underhand throw.

How far should a box be from a thrower?

The distance between the boxes should be approximately 20 feet. Most of the time players determine the distance by using a string, a rope or a chain attached to the front of both boxes. The thrower should be standing next to or behind one box while tossing washers toward the other.

Cut the Plywood and PVC Pipe

Cut the plywood and PVC pieces to the measurements outlined below. Clean up the edges with sandpaper but avoid rounding them. Sand the surfaces to smooth as needed.

Assemble the Sides

Drill and countersink two pilot holes 3/8 inches from each end of each 16-inch board and 1 inch from each long edge.

Paint

If you want to paint the PVC pipe and drain, sand them and use spray paint that adheres to plastic.

Install the Carpet, Felt or Fleece

Find the center of your square by measuring across the middle from opposite corners. Make a line an inch or two long at the middle.

Attach the Base to the Sides

Situate a 16-inch plywood square on top of one side square. Align the corners and clamp the whole piece to your work surface.

Place the PVC Pipe

Turn the drain upside down and drill three 1-inch wood screws with washers through the existing holes to secure it to the base.

Attach the Latches and Handle

Lay one box on your work surface and lay the other one on top of it. They should be face to face. When they are aligned correctly, clamp them to the table.

A B C D E F G H I J K L M N O P Q R S T U V W X Y Z 1 2 3 4 5 6 7 8 9