Full Answer
What are some common Samsung dryer error codes?
Vent Blockage test results (Clg, Cl9, Cg, C9, C80, C8o, C8, C90, C9o, Ct)
- Clg, Cg - The vent is clogged.
- C80, C8 - About 80% of the vent is clogged.
- C90, C9 - Over 90% of the vent is clogged.
- C1, CL1 - Laundry is detected inside the drum.
- Ct - The dryer is below freezing or above 104°F.
How do you fix a Samsung dryer?
Continuous Run Mode :
- Press Wrinkle Prevent + Dry Level for 7 sec during Power On State (Normal User Mode) .
- Once in Continuous Run Mode, display “CC” for 1 sec and the number of Cycle for 1 sec and the remaining time for 1.
- The previous cycle will restart during Continuous Run Mode until the mode is deactivated.
How to reset your Samsung dryer?
Outside of discarding the lint from the dryer lint trap (which you should always do, by the way), cleaning your dryer may not seem like an important thing to do, but for the functionality of your dryer, as well as your personal safety, it matters.
How to reset Samsung dryer HC error code?
The F5 E3 alert indicates there is issue with the lid lock. Remove any objects from the lid and clear any obstructions. Touch POWER to exit cycle, then touch POWER again to release lid. If this is unsuccessful, reboot the machine by unplugging the washer and wait two minutes before plugging the machine back in.
What does error code mean on dryer?
What to do if your dryer is not using an extension cord?
Why is my dryer getting hot?
About this website
How do I run a diagnostic on my Samsung dryer?
Run a Vent Blockage testWhen you're ready to start, make sure the drum is empty and then close the door. ... Press POWER to turn the dryer on and within 5 seconds, press and hold Adjust Time Up + Dry Level until InS or In appears on the display.More items...
What are the error codes on a Samsung dryer?
Error Codes ExplainedFault CodeClothes Dryer ProblemdFDoor circuit failureOdExcessive drying timeFEProblem with power supplytS or tODefective temperature sensor (electrically shorted or electrically open)5 more rows•Nov 22, 2021
How do I troubleshoot my Samsung dryer?
0:007:17And it should be tight and when you spin the drum the belt should spin with it. And that's going toMoreAnd it should be tight and when you spin the drum the belt should spin with it. And that's going to tell you you don't have a blower wheel obstruction that'll cause the dryer not to start ok.
How do I get rid of hE error on my Samsung dryer?
Resetting your dryer is easy. Unplug it (or turn off power at the circuit breaker), wait some time for the electrical charge to clear out of the dryer (usually 1 to 5 minutes at most), and then power it up again. That's it. That's all it takes to reset.
What are the symbols on Samsung dryer?
Dryer IconsSensor Dry. This icon indicates a Sensor Dry cycle is currently running.Child Lock. Child Lock is turned on. ... Delay Start. Delay Start is in use. ... Filter Reminder. This icon displays after every load as a reminder to clean the lint filter. ... Time Remaining. ... Signal Off. ... Mixed Load Bell. ... Vent Check.More items...
What do the blinking lights on my Samsung dryer mean?
60 min is blinking or Extra Low light is blinking When either of these lights are blinking, this means that the dryer is getting too hot. The most common cause is a clogged lint screen or vent system trapping heat in the dryer. Clean the lint screen, vent system, or both to correct the error.
How do I know if my Samsung dryer control board is bad?
0:151:54Either your control panel will not activate. At all this would be the low voltage side of the boardMoreEither your control panel will not activate. At all this would be the low voltage side of the board being out or you may get no heat as the relays for the heat may be compromised.
How do I run a diagnostic on my Samsung washing machine?
2:0912:58Button one button two button three and the start pause button the temperature or button one controlsMoreButton one button two button three and the start pause button the temperature or button one controls the fill cycle and tests all the water valve.
Where is the dryer reset button?
Often, dryers are equipped with a reset button on the control panel. If the motor won't run, let the dryer cool for about ten minutes. Then press this reset button.
How do I clear the CL9 code on my Samsung dryer?
On this unit, the error code CL9 indicates the child lock feature is activated. Press the temp and and time buttons and hold them for 3 seconds.
Why does my Samsung dryer turn off after a few minutes?
The dryer motor is overheating. It is the overheating dryer motor that is the first and most common cause of a dryer shutting down after a few minutes.
What would cause a Samsung dryer to overheat?
Most dryers have a felt seal at the front and rear of the drum to prevent heat from escaping the drum. If the seal is worn out or missing, the heat will not be drawn through the drum properly, causing the dryer to get too hot. Check the drum seal to ensure that it is creating a reliable seal around the drum.
Samsung Dryer Error Codes Explained - Appliance Express
If your Samsung dryer is displaying an error code, this guide will help you find the cause of it and fix it. We cover all the main error codes. Read more.
Samsung Dryer Fault And Error Codes - Help & Advice
Please do take care to read the information thoroughly as it is there to help you understand fault codes and to keep you safe. There are also some help, tips and hints with a lot of the fault codes published here that you usually will not find anywhere else and, as we learn, we add more information so if you can't find what you need please ask in the forums.
How do I run a diagnostic on my Samsung dryer?
Run a Vent Blockage test Make sure the drum is empty and then close the door. Press POWER to turn the dryer on and within 5 seconds, press and hold Adjust Time Up + Dry Level until InS or In appears on the display. Press and hold START/PAUSE to start the Vent Blockage test which lasts for approximately 2 minutes.
What to do if your dryer doesn't work?
If that doesn't work: Unplug the dryer and check for loose or damaged wire connections in the door lock/switch circuit. Reconnect the wires if loose or disconnected or replace the wire harness if damaged. If the door switch is damaged, it should be replaced.
How to clean moisture sensor in dryer?
Clean the moisture sensor inside the dryer drum with a bit of rubbing alcohol and a cotton swab. If you use dryer sheets, they coat the sensor with residue and extend drying time by tricking the sensor into thinking that moisture is still present. Take time to be sure that dryer ducts and vents are open and clog free.
How to get a dryer back in operational mode?
The first step before you do anything else to get the dryer back in operational mode is to unplug the dryer and wait at least 30 seconds before reconnecting. Sometimes just doing this will help the dryer's internal motherboard reset and begin to function properly.
What happens if my dryer is 60 Hz?
If the dryer is getting the 60 Hz power it requires, the electronic control board is faulty and must be replaced. This requires a professional. An electrician or your electrical power supplier should check the frequency of your electrical power supply when they come for the repair appointment.
How to get dryer back in operational mode?
The first step before you do anything else in order to get the dryer back in operational mode is to unplug the dryer and wait at least 30 seconds before reconnecting it. Sometimes just doing this will help the dryer's internal motherboard reset and begin to function properly. Dryer information codes. Information Codes.
What happens if my washing machine fails?
If the washing machine fails to operate, you may see an information code on the screen. In most cases, it is not a mechanical problem. Check the codes and instructions below and try the suggestions that are given.
Why is my dryer heater not working?
The problem may be caused by a fault in the gas supply, which limits the supply to the heater coils. Make sure the cut-off valve for the gas supply is fully open.
What is wrong with my dryer door?
The dryer is telling you there is something wrong with the dryer door’s switch or wiring (harness). Check the wiring and the door switch to see if there are loose connections. Otherwise, it’s best to call in a repairman. It may be that either the switch or the harness is damaged and needs replacement.
What is the EEPROM on a dryer?
The thing that commands the dryer is called the EEPROM (Electrically Erasable Programmable Read-Only Memory). It is the communication center of your dryer, located on the dryers PCB (Printed Circuit Board). This is where it all happens: orders are received, commands are given, and actions are executed from this place.
Why does my dryer tell me it's weak?
And when it’s weak, your dryer can tell, because it isn’t getting enough power. It will send you an FE message. 2) It can also be a faulty power frequency sensor in your dryer.
What does et mean on a dryer?
Et means your dryer is suffering from a serious technical error. This ‘Error is too technical’ for the machine to explain and for you to understand. When this happens, try to unplug the dryer and wait for several minutes. Then plug the dryer back.
Can a dryer be closed if it's open?
In case of electricity powered, your repairman will first check if your dryers circuit breaker is closed. If it’s open, no electricity will flow to the heater. But then he’ll have to find out what electrical problem trips the circuit breaker. If it’s faulty or damaged wiring, then he’ll replace that, too.
What to do if your dryer is not using an extension cord?
If you get this error, check that the dryer is on its own circuit and not using an extension cord. If it's an electric dryer, confirm the power cord has been installed properly and the correct voltage is being supplied.
Why is my dryer getting hot?
This means that the dryer is getting too hot. The most common cause is a clogged lint screen or vent system trapping heat in the dryer. Clean the lint screen, vent system, or both to correct the error. If the error continues after cleaning the lint screen and the exhaust vent, visit our Support Centre to request service.
Major information codes
The first step before you do anything else in order to get the dryer back in operational mode is to unplug the dryer and wait at least 30 seconds before reconnecting it. Sometimes just doing this will help the dryer's internal motherboard reset and begin to function properly.
Is this content helpful?
Thank you. Glad we were able to help. Your feedback helps us provide better support
Why is my dryer not heating?
For instance, if the dryer is not heating well, it could be due to a blocked vent.
How to reset a dryer?
Resetting your dryer is easy. Unplug it (or turn off power at the circuit breaker), wait some time for the electrical charge to clear out of the dryer (usually 1 to 5 minutes at most), and then power it up again. That's it. That's all it takes to reset.
Should I reset my computer at the first sign of trouble?
However, depending on what error you get, it's not always a good idea to reset at the first sign of trouble. Read on for how to reset, when you should or shouldn't, and what to do if a reset doesn't help.
What does error code mean on dryer?
This code means the dryer's internal components cannot communicate with each other. Shut off the dryer for 60 seconds, and then turn it back on again. If the error code remains, visit the Support Center to request service.
What to do if your dryer is not using an extension cord?
If you get this error, check that the dryer is on its own circuit and not using an extension cord. If it's an electric dryer, confirm the power cord has been installed properly and the correct voltage is being supplied.
Why is my dryer getting hot?
This means that the dryer is getting too hot. The most common cause is a clogged lint screen or vent system trapping heat in the dryer. Clean the lint screen, vent system, or both to correct the error.