The calculation process is:
- Estimate the volume of asphalt needed, using geometrical formulas and plans or measurements, including width, length, and depth (thickness).
- Estimate the density of the hotmix to be used. Standard density for asphalt is 145 lb/ft 3 (2322 kg/m 3 ).
- Multiply the volume by the density (in the same units) to get the weight
How much does it cost to replace asphalt?
With a narrower average midpoint price range, you can expect to pay about $4.50 per sq. ft. or $450 per square to replace an asphalt shingle roof on a typical single-family house up to two-stories high.
How much does it cost to repair an asphalt driveway?
Repairing your asphalt driveway tends to cost between $800 and $2,500, depending on the same factors mentioned above. The national cost average for this project is about $1,500. Several special considerations apply, especially compared to concrete driveways.
How much does asphalt cost per square foot?
Asphalt cost: $4.00 per square foot. This can vary depending on how thick it’s applied and the region in which you live. Special features: The calculator above assumes the cost of a Chip Seal top coat, stamped surface or color asphalt at $4.00 per square foot. This is probably a tad on the high side, but is within range.
What is the average cost for hot asphalt per ton?
What Is The Average Cost For Hot Asphalt Per Ton? Hot mix asphalt costs $100 to $200 per ton. This is the standard type for all-weather surfacing and repairs. Cold mix asphalt costs $10 to $50 per bag, but you can only use it for temporary repairs. How many tons of asphalt are in a dump truck? How much can you deliver in one truck
How do you figure square footage for asphalt?
1:522:12How To Quickly Figure The Cost Of An Asphalt Driveway - YouTubeYouTubeStart of suggested clipEnd of suggested clipTake a measuring tape and measure the length and the width. And then multiply it this will give youMoreTake a measuring tape and measure the length and the width. And then multiply it this will give you the square footage of your driveway.
How do you calculate the cost of an asphalt driveway?
For the simplest estimate, you can use this formula.Length x width=Square footage of the driveway.Driveway sq ft x $3= low end cost.Driveway sq ft x 7= high end cost.Driveway sq ft x $2= low end cost.Driveway sq ft x $4= high end cost.When to reseal your driveway:When to repave your driveway:
How much area will a bag of cold patch cover?
Each 50 lb (22.6 kg) bag will yield approximately 0.5 ft3 (14 L) when properly compacted and will cover an area of approximately 6 ft2 (0.56 m2) when placed at a thickness of 1 in (25 mm). Square cut the vertical sides of the hole to provide for proper confinement of the patch. Remove all loose material.
How do you calculate pavement?
Multiply the length times the width times the depth to obtain the volume in cubic feet of the space to be paved. Performing this step yields 12.5 feet times 8.33 feet times 0.42 feet or 43.7 cubic feet.
How do you quote asphalt?
To find the amount of asphalt needed, multiply the cubic footage by 145 to find the total weight needed, then divide by 2,000.
How much is a 700 ft driveway?
For a larger driveway or thicker base, the cost will be higher. For example, a driveway 15 feet wide by 700 feet long with a six inch base will need approximately 25 tons of gravel, at a material cost of about $700. With delivery, the total cost will be around $1000.
How much does a 50 lb bag of asphalt cover?
A: Each 50 lb bag will yield approximately 0.5 cubic feet when properly compacted and will cover an area of approximately 6 square fet when placed at a thickness of 1 inch.
How much is a yard of cold patch?
Asphalt is more cost-effective than concrete but requires more maintenance for homeowners. Concrete prices are $119 to $147 per yard. Asphalt lasts 15 to 30 years, while concrete lasts 30 to 40 years....Asphalt prices.UnitPrice rangePer cubic yard$80 – $160Per square foot (3” – 5” depth)$0.75 – $2.002 more rows•Dec 17, 2020
How long does cold asphalt last?
Temporary – Cold mix asphalt should only be used in temporary situations, including patches or filling in small cracks during the winter. Cold mix asphalt is only designed to last a season or two at most before being replaced by a more permanent fix.
How many yards of asphalt are in a ton?
There are approximately 0.5 cubic yards in a ton of asphalt. 1 cubic yard of asphalt weighs around 4,050 pounds and 1 ton of asphalt weighs about 2,000 pounds, so, number of yards of asphalt in a ton = 2000 ÷ 4050 = 0.5 yards approx. Thus, there are 0.5 cubic yards in one ton of asphalt.
How many cubic feet are in a ton of asphalt?
Multiply Volume by the Density Asphalt Institute notes that the density of hot-mix asphalt is around 142 to 148 pounds per cubic foot (PCF). To determine how much asphalt you will need for the project, multiply the area's cubic feet measurement by 148 PCF.
How many tons of asphalt are in a dump truck?
A typical tandem dump truck is limited to about a 13-ton payload in accordance with federal bridge law. Increased truck capacity is important when directly unloading into the asphalt paver.
How much does it cost to replace a driveway?
The national average price to replace an old road for a new one ranges anywhere from around $2,500 to $6,000, depending on the length and timeline of installation. While that may seem expensive, the cost is actually much cheaper than concrete.
Do you need a permit to lay asphalt?
Depending on the location, some projects may also require permits for individuals to lay asphalt and a license to operate rollers. It’s a good idea to ask your local municipality regarding any special needs before you make a final decision.
How much does it cost to fix hot mix asphalt?
Although not an exact price, you can expect a reasonable minimum charge for hot asphalt repairs to be in the $600-$1600 price range. Asphalt curb repair:
How deep is asphalt?
In commercial pavement, the depth of asphalt can be as little as 1″ on a poorly paved parking lot, or more than 9″ on a municipal or state road.
Asphalt calculator formula
Based on the measurements you provide for required length, width and thickness, the calculator first works out the area and volume of the hot asphalt mix required using the below formulas:
Calculation examples
Imagine I want to pave over an area measuring 20 feet by 4 feet to a thickness of 6 inches using standard asphalt (140 lb/ft³) and costing $150 per US short ton.
What if my measurements are in different units?
The best thing about our asphalt calculator is that it takes care of this for you.