You can use compression fittings that connect nylon to steel. Or just buy 3/8ths and 5/16ths steel line in rolls and connect them up. C
How to attach rubber line to metal fuel line?
A short piece of rubber line connects it to the metal line and about 24" of rubber line from the pump to the tank. All of it follows the original path of the oem line. I wrapped the rubber line with insulation where it goes over/behind the valve cover.
Can nylon be used for fuel lines?
Today's pump gasoline / gasohol is very corrosive. If the material you are using for your fuel lines does not specifically state that it is built to withstand modern fuels, DO NOT USE IT! I wasn't sure if Nylon is compatible with modern fuels, but it is. Nylon and Teflon (PTFE) can be used for soft lines.
Will nylon line stretch over steel line?
The smaller line will end up stretching over the end of the steel line as I am assuming it is flared. So, it will be stretched anyway. Nylon line is not very forgiving especialy if it is the rigid type.
Can you heat up a fuel line?
I think you are trying to merge to pieces of fuel line together. The plastic hose is smaller for a reason. It has to make a seal and hold at least 100psi and not break. There is a special tool used to make this type of line. Heating it will not help. After line is made we use a special clamp they supply with the tubing kit as added security.
Can you replace steel fuel lines with nylon?
One option for replacing metal fuel lines is with a nylon tubing and specific fittings. Nylon tubing can be used for an entire length of fuel line or just a section. This option can be a cost-effective and time-efficient repair when pre-bent lines are not available.
How do you attach nylon fuel line?
2:544:24BEST ways to repair dorman nylon plastic fuel line tubing - YouTubeYouTubeStart of suggested clipEnd of suggested clipNow that the hose is on you want to put the hose clamp on and then take a pair of flush. Cut pliers.MoreNow that the hose is on you want to put the hose clamp on and then take a pair of flush. Cut pliers. And crimp it on tightly.
Can I use a compression fitting on a steel fuel line?
You can get hydraulic compression fittings anywhere hydraulic hoses are made. These fittings are much more substantial then "plumbing" compression fittings. I wouldn't be afraid to use them. They are normally steel (not brass) and use 2 compression sleeves.
Can nylon tubing be used for fuel line?
Nylon fuel line. Many late-model production cars are now using hard, black nylon tubing with special connectors to attach fuel-feed lines to the gas tank sending unit/fuel pump modules. This gas-resistant nylon tubing can be purchased by the foot or in short sections with the proper ends already attached to one end.
Can you use hose clamps on nylon fuel line?
Our 1/4” stainless steel hose clamps are designed explicitly for nylon fuel lines and can work on lines that hold up to 200 PSI.
How do you cut nylon braided fuel line?
1:042:40TTTT February 4, 2020. How to cut braided fuel line the FUN way!YouTubeStart of suggested clipEnd of suggested clipPut your hatchet where you want it I just hold it in place with my with my hatchet. Take my hammer.MorePut your hatchet where you want it I just hold it in place with my with my hatchet. Take my hammer.
Can you put a compression fitting on a fuel line?
As long as the fittings are double ferrule fittings like swagelok or gyrolok you are fine. Do not use the cheap single ferrule fittings under any circumstances. The ferrules do not stay straight.
Can you use brass fittings on fuel lines?
It is common to find brass fittings in the air brake systems, cab controls, fuel systems, engine, transmission, cooling and air tanks on a heavy-duty truck and they meet DOT and SAE requirements. Let's take a deeper look into why brass is an ideal material for this market.
Do you have to flare compression fittings?
The type of fitting you use depends largely on how tight your seal must be. When any level of leakage is an issue (gas and high-pressure lines, for example), use flare fittings. When slight levels of leakage won't cause too much of a problem (water and compressed air lines, for example), use flareless fittings.
Does nylon hold up to gasoline?
Nylon resistance to gasoline. Nylon is one of the most gasoline-resistant resins. That said, high-octane gasoline will cause some deterioration in nylon.
What is the best metal for fuel line?
Most cars come from the factory with Metal Lines because they hold up better than any soft material. They are usually made from stainless, aluminum or coated steel tube. Metal is the best material for fuel lines. However, it can be difficult to fabricate.
What is best material for fuel line?
The best fuel line material depends on your needs. However, the best material for fuel lines is polytetrafluoroethylene or PTFE. PTFE fuel line is made of plastic material specifically known as Teflon. This fuel line material is impervious is resistant to the degenerative fuel effects which could form vapor barriers.
How do you join a fuel line?
4:327:27Repairing Damaged Fuel Lines with BrakeQuip - Gear Up With Gregg'sYouTubeStart of suggested clipEnd of suggested clipThat's the compression sleeves in the Union itself. You start by sliding the nut onto the tube orMoreThat's the compression sleeves in the Union itself. You start by sliding the nut onto the tube or pipe and then sliding the sleeve on behind it push the Union as far as it will go.
How do you hook up fuel line fittings?
0:384:21How to Disconnect Common Fuel Line Fittings - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd pull it off in order to reinstall a push type connector just push it on until you hear it clickMoreAnd pull it off in order to reinstall a push type connector just push it on until you hear it click in order to install the push and lock stock connector push it under your fitting.
How do you fit a tight fuel hose?
2:113:14How To : Fit rubber fuel line onto bigger metal line. - YouTubeYouTubeStart of suggested clipEnd of suggested clipMake the hose clamp a little bit bigger. Slide. It into place tighten it down done.MoreMake the hose clamp a little bit bigger. Slide. It into place tighten it down done.
How do I connect two fuel lines?
1:056:36How to mate brake or fuel lines with a double flare union - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo one way to do that is to flare using that rigid tool that I demonstrated. And use the appropriateMoreSo one way to do that is to flare using that rigid tool that I demonstrated. And use the appropriate tube nuts and sleeves here this line obviously isn't flared.