Determining The Correct SharkBite Fitting Size
| SharkBite Fitting Size | Nominal Pipe Diameter | Pipe OD | Pipe Insertion Depth (IN) | Pipe Insertion Depth (MM) |
| 1/4 in. | 1/4 in. CTS | 3/8 in. | 0.82 | 21 |
| 3/8 in. | 3/8 in. CTS | 1/2 in. | 0.94 | 24 |
| 1/2 in. | 1/2 in. CTS | 5/8 in. | 0.95 | 24 |
| 5/8 in. | 5/8 in. CTS | 3/4 in. | 1.13 | 29 |
Full Answer
How do you use a Sharkbite pipe?
Insert the pipe into the SharkBite fitting. You need to insert the pipe through the release collar allowing it to sit against the grab ring. Push the pipe. Using a slight twisting motion, push the pipe firmly into the SharkBite fitting until you hit the tube stop.
Can Sharkbite fittings be used underground?
Although recommended to be used in accordance with an access panel, SharkBite fittings are IAPMO tested and are approved for underground and behind-the-wall use. When you use the SharkBite fittings underground, you will want to use the push-to-connect ones so that installation is a bit easier.
How do you measure for Sharkbite fittings?
Measure one inch up the pipe from the cut end and mark the pipe with a pencil or scribe. Make sure the mark is easily visible as it will help you install the SharkBite fitting correctly.
Can Sharkbite be used on PEX?
The threaded Sharkbite is compatible with copper, PEX, CPVC, PE-RT, and SDR-9 HDPE pipes. They offer easy and quick installation. Also, no special tools, glue, crimping, or soldering are needed.
How much pipe do you need for a SharkBite?
Pipe Insertion Depth ChartSharkBite Fitting SizeNominal Pipe SizePipe Insertion Depth (mm)1/2 in.1/2 in. CTS245/8 in.5/8 in. CTS293/4 in.3/4 in. CTS281 in.1 in. CTS335 more rows
How far in does a pipe have to go into a SharkBite fitting?
Push the pipe firmly with a slight twisting action until it reaches the tube stop. To ensure that the pipe is correctly inserted, check that the depth mark is within 0.005 in (0.13 mm) of the end of the release collar.
How do you measure for a SharkBite?
0:582:05How to Install SharkBite Push-to-Connect Fittings - YouTubeYouTubeStart of suggested clipEnd of suggested clipIf you're handling copper pipe remove any sharp edges or burrs on the pipe. Next. Use your sharkbiteMoreIf you're handling copper pipe remove any sharp edges or burrs on the pipe. Next. Use your sharkbite depth and D bar tool to measure and Mark the insertion depth on your pipe.
Do professional plumbers use SharkBite?
When and when not to use SharkBite fittings. Most professional plumbers believe that SharkBite fittings and other kinds of push-fit fittings should only be used as an emergency, temporary fix, and not for any enclosed or permanent plumbing system. However, there is a growing selection of DIYers who would disagree.
Should I sand copper pipe before SharkBite?
Do not sand the copper pipe – while it's the easiest way to smooth out the edge of the pipe, this practice should be avoided whenever possible since it disrupts the otherwise even pipe surface and may compromise the seal.
Are shark bites code?
SharkBite Codes (Working) SHARKBITE2 - Redeem for 200 Shark Teeth. 1BILLION - Redeem code for 100 Shark Teeth. SimonsSpace - Redeem code for 50 Shark Teeth. FROGGYBOAT - Redeem code for 50 Shark Teeth.
How do you cut copper pipe for SharkBite?
3:216:46Repair Copper Pipe Leaks with SharkBites (Super EASY) - YouTubeYouTubeStart of suggested clipEnd of suggested clipTool to cut out that damaged piece of copper pipe this is why we love the autocut. Tool it onlyMoreTool to cut out that damaged piece of copper pipe this is why we love the autocut. Tool it only takes a few seconds to do that then deburr the outside edge of the copper pipe with the sharkbite.
How do you measure the size of a pipe?
Measure the Outside Diameter (OD) of your pipe or pipe fitting:Wrap a string around the pipe.Mark the point where the string touches together.Use a ruler or measuring tape to find the length between the tip of the string and the mark you made (circumference)Divide the circumference by 3.14159.
Are SharkBite fittings reliable?
John Guest quick-connect and SharkBite fittings are both reliable and awesome fittings for emergency fixes. Even though Quick-Connect and SharkBite fittings are rated for use underground and behind walls, soldering pipes may be the smarter choice.
What do plumbers think of shark bites?
0:578:41Why I Don't Use Sharkbite Fittings on My Plumbing Jobs - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd here's why these are what sharkbite calls a temporary fitting. And these are called a permanentMoreAnd here's why these are what sharkbite calls a temporary fitting. And these are called a permanent fitting meaning you can take this one off this one you can't and i'm going to talk about the
Are shark bites good for hot water?
Yes, you can use SharkBite fittings on hot water lines. Remember, however, that they only work with copper, PEX, and CPVC pipes.
Can shark bites be reused?
You can reuse SharkBite fittings 2–3 times before the O-ring that provides a waterproof seal is compromised to the point where it may leak. It's also important to note that repeatedly removing a SharkBite fitting from the same pipe may cause scratches in the pipe.
How to make a sharkbite pipe?
Hold the SharkBite fitting and push the pipe into the fitting with a twisting motion. Push the pipe into the fitting until you hear a "click" sound coming from the fitting. Look for the pencil mark that you made on the pipe. Make sure the mark is flush, or nearly flush, with the edge of the release ring on the SharkBite fitting. Push the pipe farther into the fitting if the mark is more than .05 inches from the release ring.
How to install Sharkbite fitting?
Step 1. Cut the pipe that you are installing in the SharkBite fitting with a pipe cutter. Make sure the end of the pipe is flush and square, without cracks or deformations. Use the deburring tool on the back of the pipe cutter to remove any burrs from the end of the pipe.
Do sharkbite fittings need solvents?
SharkBite fittings eliminate the need for solvents, crimpers and torches. Installing or repairing water lines in your home usually requires the use of adhesives, crimpers or solder. Adhesives can be messy and smell terrible, crimpers are expensive and hard to use in small areas and solder involves using an open flame to heat pipes, ...
