| Size | Coverage |
|---|---|
| 1 Gallon (3.78 L) | 25 sq. ft. (2.3 M2) |
| 3.5 Gallon (13.2 L) | 88 sq. ft. (8.2 M M2) |
| RedGard as Waterproof Membrane: | |
| 1 Gallon (3.78 L) | 55 sq. ft. (5.1 M2) |
How much will a gallon of RedGard cover?
$64.99Container Size3.5 Gal.Coverage Area192 Sq. Ft.Shelf Life18 Mo.BrandRedGardUPC000101867717485 more rows
How thick can you apply RedGard?
Combined dried coatings must be at least 30-35 mils thick. When wet, the combined coatings must be at least 60-70 mils and must not exceed 125 mils wet-film thickness. RedGard® is dry when it turns solid red, with no visible pink color.
How long do I wait between coats of RedGard?
1:364:26How to Install RedGard Waterproofing and Crack Prevention MembraneYouTubeStart of suggested clipEnd of suggested clipAnd the intersections where floors and walls meet spread red guards six inches on each side of theMoreAnd the intersections where floors and walls meet spread red guards six inches on each side of the intersection. Changes of plane or gaps more than 1/8 inch should be reinforced with six inch wide
Can I tile directly over redguard?
Can You Tile Directly Onto RedGard? There's no need to put another layer of product on top of RedGard before you begin tiling. A surface that has been painted with RedGard and allowed to dry is ready for you to apply thinset and install tile. You can install thinset mortar and tile directly onto RedGard.
Is 1 coat of RedGard enough?
For tile installations bonding directly to the substrate; strongly recommended to apply at least one full coat of "undiluted" RedGard® to the "dry" primed area and allow to dry completely before tile installation work is to begin. When used as a vapor barrier, apply one full coat (70 sq. ft.
How many coats of red guard do I need?
4:4414:36Redgard How Many Coats Do I Need to Apply to Waterproof ... - YouTubeYouTubeStart of suggested clipEnd of suggested clipNow a typical credit card might be about 30 mils depending on the material of the credit. Card soMoreNow a typical credit card might be about 30 mils depending on the material of the credit. Card so that might be a good starting place if you don't have one of those wet. Gauges. So we're going to
How long to let RedGard dry before tiling?
Depending on ambient conditions, drying time can take up to 12 hours. A water test can be conducted 72 hours after application if required. Clean tools and hands with water before material dries.
How long will redguard last?
$179.99Container Size1 Gal.FormulationElastomericFor Use WithInterior / Exterior Tile, Stone, MasonryCoverage Area110 Sq. Ft.Shelf Life18 Mo.5 more rows
What kind of thinset do I use over redguard?
The Flexbond modified thinset, which is sold at HD, lists redgard as one of the surfaces it can be applied to and therefore, following manufacturer recommendations, a person should be using a modified thinset like Flexbond over Redgard.
Can you put RedGard on drywall?
9:0927:29REDGARD EXPERIMENT ON DRYWALL - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd even though red guard says you cannot use it on a gypsum product because it's paper it's all itMoreAnd even though red guard says you cannot use it on a gypsum product because it's paper it's all it is as a paper backing. They don't recommend it for paper.
How many coats RedGard steam shower?
CUSTOM recommends a minimum of two coats for waterproofing; the second coat also fills any imperfections that may exist in the coverage. By applying the RedGard at a rate of 50 square feet per gallon for each coat, two coats will achieve a dry film thickness of 30 mils.
Can I use RedGard on drywall?
9:0927:29REDGARD EXPERIMENT ON DRYWALL - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd even though red guard says you cannot use it on a gypsum product because it's paper it's all itMoreAnd even though red guard says you cannot use it on a gypsum product because it's paper it's all it is as a paper backing. They don't recommend it for paper.
How long does Thinset need to dry before RedGard?
Set the tile into the thin-set while it is still wet. Once the tile is set, do not touch, move, or walk on the tile for 24 hours to allow the thin-set to cure undisturbed.
How long does it take RedGard to dry?
The product is dry when it turns solid red with no pink showing, normally 1-1/2 to 2 hours. Depending on ambient conditions, drying time can take up to 12 hours. A water test can be conducted 72 hours after application if required. Clean tools and hands with water before material dries.
Is a vapor barrier necessary behind cement board?
If it's a cement board, you need a vapor barrier, because cement retains moisture, which means the wood next to it is always damp. It does retain moisture, but the advice given by others here is to move the waterproofing between the tile and cement board with products like Redguard or Ditra.