| Size | Square feet | Average cost |
|---|---|---|
| 24x24 Driveway (2-Car) | 576 | $1,700 – $6,900 |
| 24x36 Driveway (3-Car) | 864 | $2,600 – $10,350 |
| 50' Diameter circular driveway | 1,650 | $5,000 – $15,000 |
| 10x10 Driveway extension or apron | 100 | $300 – $1,200 |
How much do driveway pavers cost per square foot?
Cost to Pave a 2-car Driveway; National Average 20’x24′ 480 sq. ft. $4,700: Low: $2,850: Mid-range: $4,200: High-end: $6,860
How much does it cost to repave a 2 car driveway?
24/01/2020 · How much does it cost to pave a dirt driveway? A typical two-car driveway is 16 feet wide and 38 feet long without curves or slope, for a total surface area of 610 square feet. It will typically cost $1.30 per square foot to be professionally supplied and paved with gravel.
How much does a cobblestone driveway cost?
31/05/2010 · Cost to Pave Medium-Size Driveway. The cost to pave a medium-sized driveway ranges between $3,200 and $14,400. They can be double stall with a size of 20’ x 20’ or double with a size of 24’ x 24’. As their name suggests, they can fit two vehicles, but make sure to consider the size of the vehicles.
How much does it cost to widen a driveway?
Driveway pavers cost $10 to $30 per square foot on average for materials and labor. The average cost to install a 24’ x 24’ (2-car) paver driveway is $5,700 to $17,200. A high-end block paving stone or brick driveway costs $25 to $50 per square foot or between $15,000 and $30,000.
How many square feet is a 2 car driveway?
640 square feetSize: The average 2-car driveway in the U.S. is 16 x 40 feet, or a total of 640 square feet. Many driveways may be larger or smaller, depending on the distance from the garage or house to the street and possible extensions for RV parking.
What is the cheapest type of driveway?
gravelAdvantages of Aggregate Driveways Pound for pound, aggregate is the cheapest of these four common driveway materials. A basic gravel driveway can cost as little as $0.50 per square foot – an order of magnitude less than a professionally installed asphalt, stone, or concrete driveway.
Is blacktop cheaper than concrete?
The cost of an asphalt driveway is typically cheaper than concrete, costing $2.00 – $4.00 per square foot. Asphalt prices tend to fluctuate with fluctuations in crude oil prices. In contrast, a concrete driveway costs between $4.00 – $6.00 per square foot for a standard installation.13-Jun-2018
Is it worth it to pave driveway?
Asphalt is more flexible making it less likely to crack over time. Asphalt driveways can last you 20-25 years if properly installed and maintained – a great investment. One final point about paved driveways. While they increase the value of your home, a nice paved driveway can also help sell your home FASTER.
Can you pave a driveway yourself?
Making your own asphalt driveway is hard work, and not a job for one person. If you have friends who will help you, it is possible to save a lot of money by doing your own driveway, even after the cost of rental equipment is factored in.
What is the cheapest way to pave driveway?
Gravel driveways are hands-down the most affordable option upfront. Asphalt driveways place second in cost, followed by cement and pavers. Although gravel driveways are the least expensive initially, they require the most maintenance long-term.
What is the difference between asphalt and blacktop?
Asphalt generally refers to major highways and streets, whereas, blacktop is commonly used to refer to driveways and residential roads. As a matter of fact, blacktop is a type of asphalt.
What type of driveway lasts the longest?
ConcreteConcrete. Concrete is the old standby for driveways. Most suburban homes opt for this material for two big reasons: Concrete is typically the longest-lasting driveway surface, and, if installed properly, it is practically maintenance-free.15-Jul-2016
What type of driveway is best?
Longevity: The longevity of an asphalt driveway is a lot higher than most other driveway options. Homeowners can expect their asphalt driveway to last at least 20 years. Durability: Asphalt driveways are hard wearing and durable. The seal that is applied on top of your asphalt driveway encourages greater longevity.17-Jan-2018
Does doing a driveway increase home value?
How much value does a driveway add to a home? According to Property Price Advice, a driveway can add between 5 and 10% to your home's value.
Does adding a driveway increase house value?
You may be surprised to learn that a driveway does add value to your home. On estimate a driveway can increase your property's value by 5-10%. That is quite a bit for an area you do not really need to pay a lot to revamp. Location is key to understanding how valuable a driveway would be.23-Jul-2020
Is a new driveway a good investment?
You can definitely get a great return on your investment. At the very least your property value increase will cover the cost of the driveway. The amount of added value can fluctuate. Depending on the home, a new driveway can add around $5,000 to $7,000 in value.18-May-2020
How much does it cost to resurface a 4 lane road?
As I mentioned, it's much less expensive to maintain existing roadways. To mill and resurface a 4-lane road, it costs an average of $1.25 million per mile. Then, if you want to expand said road from four lanes to six, you can expect to pay roughly $4 million.
How much does it cost to install an asphalt driveway?
Other sources estimate the cost to install an asphalt driveway to be between $2,300 and $10,300. Homeowners typically pay per square foot. Reibling adds the average cost per square foot is between $3.50 and $4.50.
How much does asphalt cost per square foot?
Asphalt prices tend to fluctuate with fluctuations in crude oil prices. In contrast, a concrete driveway costs between $4.00 – $6.00 per square foot for a standard installation.
Why is it important to have a driveway freshly paved?
Having your driveway freshly paved will not only make your property look better, but it will also help prevent damage due to potholes and other issues inherent with older driveways.
What is interlocking pavers?
Interlocking Pavers. Interlocking pavers are one of the most durable and attractive forms of driveway paving. The pavers can be made of concrete, stone, brick, or composites and come in many shapes, sizes, and colors. Therefore, it is possible to create very interesting and unique designs.
How much does gravel cost?
Gravel. Gravel is the least expensive material you can use for your driveway, costing between $1 and $2 a square foot. In warm climates, it can last for decades with little maintenance. But in areas that see snowfall, plows and shovels can disturb the gravel, and pieces of rock can damage snowblowers.
Do you need to level a driveway before paving?
Most driveways must be leveled and compacted prior to paving. If you are repaving an existing driveway, this is generally not needed. If this is new construction, however , the driveway will need to be leveled and compacted before beginning.
What is tar and chip driveway?
Chip-sealed driveways, also called tar-and-chip, are a way to make asphalt driveways more durable and longer-lasting. A layer of asphalt is put down first, then a layer of aggregate is put on top and compacted into the tar.
How much does stamped concrete cost?
Stamped concrete is an attractive way to add color and design to a driveway. It costs around $8 to $12 a square foot, and multiple patterns and colors are available, which allows for customization. Like poured concrete, it does better in hot climates than cold climates and can be expensive and difficult to repair.
What is the maintenance of a driveway?
Maintenance. Maintenance for driveways depends a lot on the climate you live in and the type of driveway. For both asphalt and concrete driveways, pay attention to cracks, frost heaves, and other structural problems with the material.
What materials are used to make a paver driveway?
The main driveway materials are concrete, stone, and brick. Choose from flat top, beveled, textured, tumbled, polished, honed, saw cut, sandblasted, flamed, chiseled edge, or antiqued.
How much does it cost to install a concrete block driveway?
An average concrete block paving driveway costs $10 to $20 per square foot or between $5,500 to $11,500 for materials and installation. The price of concrete driveway pavers depends on the size, thickness, design, strength, and color.
How strong is a concrete driveway?
Concrete driveway pavers have a minimum strength of 8,000 PSI, and are sold in many shapes in shades of brown, gray, and red. Concrete pavers sometimes spall—flake or break up—because they are more prone to retaining moisture, with a max absorption rate of 5%.
How much does it cost to install a driveway with pavers?
Installing a driveway with grass pavers costs $10 to $20 per square foot or from $5,500 to $12,000, depending on the size and type of materials. Grass paver systems are either concrete or plastic and are honeycomb-type cells that combine the look of a lawn with the function of pavement.
How much does porcelain paver cost?
A porcelain paver driveway costs $15 to $30 per square foot for materials and installation. Porcelain is stronger, lighter, and easier to install than natural stone or concrete pavers. With a low water absorption rate of 0.1 to 0.5%, porcelain doesn’t crack easily.
How much does it cost to extend a driveway?
The average cost to extend or widen a driveway with pavers is $10 to $25 per square foot. Adding 3' of pavers to widen a driveway or extending a driveway by 5' with pavers costs $1,200 to $3,600 installed. The sides of the driveway will need a sub-grade layer for proper drainage.
How long does a paver driveway last?
A paver driveway lasts 25 to 75 years, depending on the quality of installation work, the types of pavers, the maintenance steps taken, and the local weather. Compare this to a concrete driveway that lasts 20 to 30 years on average.
What questions should I ask a driveway contractor?
Questions to ask driveway contractors 1 Can you provide me examples or addresses of your previous driveway paving jobs? 2 Will you be using control joints or wooden expansion joints to minimize concrete cracking? 3 Are you licensed, insured, and bonded? 4 Does the estimate include all materials and labor fees? What additional costs can I expect? 5 What permits do I need, and will you obtain them? 6 How do you handle damages that happen on the job? 7 What does your warranty policy include? 8 What is your payment schedule?
What is the cheapest driveway material?
The cheapest driveway material is gravel at $1 to $3 per square foot using aggregate made of crushed shells, crushed concrete or asphalt, or pea gravel . Tar and chip seal driveways are the second cheapest at $2 to $5 per square foot.
How much does it cost to install a concrete driveway?
Concrete driveway. Installing a concrete driveway costs $2,400 to $4,800 on average or $4 to $8 per square foot for plain gray concrete. Adding decorative colors, borders, stamped patterns, and finishes costs $8 to $18 per square foot. Concrete lasts 30 to 40 years and handles hot climates better than asphalt.
Does a paved driveway increase the value of a house?
If most homes in the neighborhood have gravel driveways, a paved driveway sets a house apart, increasing its value. If other homes have paved driveways, replacing a gravel driveway with concrete or asphalt increases the value.
How much does gravel cost?
Well-built gravel driveways require light raking and new gravel once or twice a year. Gravel prices range from $10 to $50 per ton, depending on the stone size and type.
How much does a chip seal driveway cost?
Chip seal driveway. Chip seal driveways cost $1,200 to $3,000 or $2 to $5 per square foot. Chip seal, also called tar and chip, lasts 7 to 10 years. Tar and chip driveways have the durability of blacktop, come in various colors, and feature layers of stone aggregate spread over hot liquid asphalt.
How much does it cost to widen a driveway?
Widening a driveway costs $3 to $12 per square foot , depending on the materials. Adding 200 square feet of driveway surface costs $600 to $2,400 on average. Minimum and maximum driveway widths may be subject to local zoning regulations.
How much does it cost to pave an asphalt driveway?
Contractors consider asphalt one of the cheapest options. Paving an asphalt driveway ranges from $2,300 to $10,300, according to costhelper.com, and Angie’s List members nationally reported an average price of $5,308 to pave an asphalt driveway. “Asphalt is certainly less expensive than concrete, but it is also smoother because it does not have ...
How long does asphalt last?
If homeowners reseal the asphalt driveway every three years, it will last about 20 years, according to the National Asphalt Pavement Association. Asphalt should be 3 inches thick when used over gravel for new driveways, and 2 inches thick when repaving, Leggett says. Some contractors disagree, but he argues thicker is better.
How long does a concrete driveway last?
If properly maintained, a concrete driveway can last for about 30 years and continue to cure and harden, says Prisciliano Anaya, president of Anaya Concrete in Denver. “Concrete that’s eight years old is much stronger than concrete that’s two years old,” he says. Concrete driveways should be at least 4 inches thick to support regular vehicles ...
How thick should a concrete driveway be?
Concrete driveways should be at least 4 inches thick to support regular vehicles and at least 5 inches thick for heavier trucks, according to the American Concrete Pavement Association. Concrete driveways cost more, starting around $3,500, according to costhelper.com. Angie’s List members nationally reported an average price ...
How much psi does a concrete driveway need?
Concrete pavers come with a strength rating of 9,000 pounds per square inch, and 12,000 psi for clay, he says. Concrete driveways usually use 4,000 psi of cement. However, some differences exist. Clay pavers feature a deeper, more vibrant color than concrete pavers, Calistro says.
How much does a clay paver driveway cost?
Clay pavers sometimes cost twice as much, and unlike concrete pavers, they only come in one shape, he adds. Concrete paver driveways sometimes cost up to $14,500, while clay brick driveways can reach $28,000, according to costhelper.com. Both require little to no upkeep, though concrete pavers require sealing every five to seven years, ...
Can you add decorative elements to concrete?
Classing up the basics. Homeowners also can add decorative elements to concrete and asphalt driveways. One common option involves stamping a pattern into the materials, creating a faux paver. But adding a single decorative element can add thousands to the price.
Why do you need to have a place to flow when you have a driveway?
Though most materials are porous to some extent, rainfall needs to have a place to flow to prevent pooling around the foundation or in the middle of the driveway, where it could damage the surface over time. Driveways with slopes or angles need to be carefully sloped to force water to flow in the preferred direction.
What is the best material to pave a driveway?
Homeowners aren’t limited to concrete or asphalt for a driveway, though they are the most common choices. Those who have stylish homes may prefer to pave a driveway with materials that match their exterior, and green-space lovers may choose a grass paver alternative. The material choice will significantly influence the total price to pave a driveway. Gravel tends to be cheaper, and stone pavers typically cost more. Determine your budget, then consider the options that meet your needs and preferences.
How much does it cost to build a paver driveway?
Preparing the ground for a driveway is one of the most critical steps to building a quality paver driveway and averages between $5 and $8 per square foot. If the site needs significant grading, heavy equipment will remove rocks and add topsoil before tamping it down. Trees and plants will need to be removed as well, which could require special equipment or subcontractors. The driveway installers will level the ground or work with an existing slope to drain water properly.
Is pavers cheaper than gravel?
The material choice will significantly influence the total price to pave a driveway. Gravel tends to be cheaper, and stone pavers typically cost more. Determine your budget, then consider the options that meet your needs and preferences.
What is the best way to make a driveway eco friendly?
Rubber. For an eco-friendly option, consider a rubber driveway that can be designed in a variety of colors. Recycled rubber is poured on existing concrete or asphalt to create a surface with a slight softness to it, which may save a few skinned knees.
How long does concrete last?
Concrete can crack in extremely cold temperatures, but it lasts up to 40 years while being relatively low maintenance, which is why it’s so popular.
Why are suburban cities important?
Suburban cities are typically planned to make neighborhoods neat and orderly. In some areas, houses aren’t built at the same distance from the street as every other house, and terrain can vary from one place to the next. Ensuring the garage is accessible between the street and the house is crucial and can cost extra if the preparation process is complicated. Laying concrete or asphalt on a slope may also cost more to make sure it retains the proper angle.
How much does it cost to pave a concrete driveway?
The average cost for a standard two car-driveway measuring 16′ ft. x 40′ ft. that equals 640 sq. ft. with a a minimum of 1/8 inch per foot slope for drainage will cost you $3,840 – $4,480 or $6-7.00 per square ft.. This would be on the low-end.
Additional Cost Factors
Your standard driveway is normally a minimum of 4 inches in thickness with a reinforced wire mesh. Which cost on average .30 – $.80 per square for materials and installation.
Concrete Driveways – Pricing and Installation Cost Checklist
Expect the Concrete driveway prices to fluctuate between various companies – each and every company have different operation expenses and over-head.