Receiving Helpdesk

how much does it cost to install landscape timbers

by Eileen Little Published 3 years ago Updated 3 years ago

Full Answer

What does it take to install landscape timbers?

Basic labor to install landscape timbers with favorable site conditions. Excavate area. Set timber to be level and secure with spikes at timber ends. Includes planning, equipment and material acquisition, area preparation and protection, setup and cleanup.

How much does it cost to install a timber retaining wall?

The average cost to install a timber retaining wall is about $10 per square foot or $1000 for DIY installation of a 20′ long x 5′ high wall (100 sf). If hiring a Pro, the same retaining wall cost is about $2,800 or $28 per square foot.

What is included in the cost of landscape construction?

Includes planning, equipment and material acquisition, area preparation and protection, setup and cleanup. Cost of related materials and supplies typically required to install landscape timbers including: tool and machine consumables and fuel, basic landscape maintenance and repair materials.

How do you install Timbers on top of a garden bed?

This is a good idea if the bed or other area beyond the edging will be covered with rock, mulch, or other ground cover. Roll out the fabric over the soil and position it so it is even with the mason's line; you will install the timbers on top of the fabric.

How do you anchor landscape timbers to the ground?

Secure the timber border to the ground with rebar, if desired. Drill 3/8-inch holes through the centers of the timbers, spacing the holes about 4 feet apart. Pin the timbers to the soil with 12-inch lengths of #3 (3/8-inch-diameter) rebar driven with a hand sledge.

How much is edging per linear foot?

The average cost for professional landscape edging, including materials and labor, is $4–10 per linear foot. A typical homeowner might install 180 feet of edging, at a cost of $720–1,800.

How do you install 4x4 landscape timbers?

0:4217:46Laying Landscaping Timber Project And Lessons Learned Using Mulch ...YouTubeStart of suggested clipEnd of suggested clipAnd dug the trench that the timbers are is going are going to sit in um one thing i the next step inMoreAnd dug the trench that the timbers are is going are going to sit in um one thing i the next step in the process. Here is that i'm going to actually add a few more stakes.

How do you install landscape timbers?

Dig a level trench along the line, about 3 to 4 inches deep. If building a bed that requires the length of two timbers, place the timbers together tightly, end-to-end, and make sure they're level. Corners should be perpendicular and without open spaces.

How do you price edging?

1:053:50How to BID Edging - YouTubeYouTubeStart of suggested clipEnd of suggested clipStraight line stick is about sixteen. Dollars plus tax for the really good stuff. We're gonna callMoreStraight line stick is about sixteen. Dollars plus tax for the really good stuff. We're gonna call it twenty bucks per twenty linear feet that means our material. Cost is one dollar per linear foot.

How is landscape edging calculated?

If you have a uniformly square landscape, then multiply the length of one side by 4. The number you get is your landscape edging's measure. If you don't have a uniformly square landscape, then add up the length of the four sides. The number you get is the measurement of your landscape edging.

How high can you stack landscape timbers?

Secure Stacks With Rebar This is the same rule of thumb used for fence posts, and it means a stack of landscape timbers 12 inches high would need to be secured with a 16- to 18-inch piece of rebar. Lay the landscape timbers flat on the ground in the configuration that you want (i.e., staggered joints).

How do you keep landscape timbers from rotting?

The active ingredients may vary, but the solution commonly includes alkaline copper quaternary, copper azole or micronized copper azole. These ingredients are key in protecting the wood from termites, fungus and moisture.

How do you tie landscaping timbers together?

Use a drill bit that is slightly smaller than the landscape timber spike. The spike will permanently connect the two timbers together so they do not fall off each other. Position the timber spike into the pre-formed hole and use a sledgehammer to drive the spike completely into the hole.

What is landscape timber edging?

Landscape timber edging is easy to install and creates an attractive, natural-looking frame for a flower border or perennial flower bed. You can also use it to line areas of grass. It's much more substantial and attractive than galvanized metal edging, and it will hold up better than plastic.

How to install wood edging?

The trick to installing timber edging is getting the ground flat and the edging path straight. Wood doesn't bend or dip to conform to ground contours. To turn corners with wood edging, you must fit the timbers together at an angle, much like with baseboard trim inside your house. To make a 90-degree turn, you can simply butt the square ends ...

How to make a turn in a wood edging?

Cut Angles to Make Turns. Use a protractor to lay out angle cuts for turns in your edging that are not 90 degrees. Place the protractor on top of the timber and align the protractor 's base line with the edge of the timber. Mark the edge of the timber at the protractor's center mark.

What is the best fabric for landscape?

If you want your landscape fabric to last (and to suppress weeds effectively), choose a commercial-grade spun fabric. These materials are much tougher than plastic and let water and air pass through, allowing the soil to breathe. 1

Can you put timbers on top of a mason's line?

This is a good idea if the bed or other area beyond the edging will be covered with rock, mulch, or other ground cover. Roll out the fabric over the soil and position it so it is even with the mason's line ; you will install the timbers on top of the fabric.

How much does it cost to install a retaining wall?

The average cost to install a timber retaining wall is about $10 per square foot or $1000 for DIY installation of a 20′ long x 5′ high wall (100 sf). If hiring a Pro, the same retaining wall cost is about $2,800 or $28 per square foot.

How long do retaining walls last?

Wood retaining walls are typically built with pressure-treated timber, and they’ll last 40 years or more , when treated or preserved properly.

image
A B C D E F G H I J K L M N O P Q R S T U V W X Y Z 1 2 3 4 5 6 7 8 9