How do I choose the right size wooden gates?
The first thing to consider when placing an order with us for your wooden gates are the sizes required. For the basis of a quote a rough idea of the sizes needed is ok (to within an inch/25mm or so in both height and width is ok).
How wide should a gate be for a front porch?
If a 3' wide walk gate is enough, forget the 1' waste on the rails and make it 3' (2 x 4's are usually 8' long). Every foot adds weight that will eventually make the gate more prone to sagging. On widths of 6' or more, use a double swing gate. Gates of 16' opening size are the widest possible with wood frames.
What size Farm Gate do I need for my property?
Farm Gates: Weight Is More Important Than Gauge. Typically a 2-inch diameter heavy-duty gate (for example 12-foot length by 62-inch height and 118 pounds) is best for high containment and high traffic areas while the lighter weight gates are great for the majority of your property.
Are all wood framed gates with automatic gate operators a good idea?
All wood framed gates with automatic gate operators are not a good idea. The additional strain on the wood frame will cause more problems than normally associated with wood frames. The welded steel framed gates are a better choice. The steel frame is strong enough to take the abuse of the operator.
How much does a driveway gate weigh?
Q: How much do steel and aluminum driveway gates weigh? A: Steel gates generally weigh approximately 25 lbs per linear foot. Therefore a 10′ steel gate panel would weigh approximately 250lbs. Aluminum gates generally weigh approximately 8.3 lbs/ft.
How do you hang a heavy wooden gate?
4:096:56Hanging your wooden gates - Gate fitting guide - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo start enough on the side of the gate where the hinges are put your drill bit on to the gate.MoreSo start enough on the side of the gate where the hinges are put your drill bit on to the gate. Through the square bolt hole and start drilling each hole until your drill bit just starts to protrude.
How do you support a heavy gate?
1:169:14How to Fix a Large Sagging Gate - YouTubeYouTubeStart of suggested clipEnd of suggested clipThis bottom corner at all you're just gonna be putting more weight right into the middle. So what weMoreThis bottom corner at all you're just gonna be putting more weight right into the middle. So what we're going to end up doing is bracing it from the middle towards the outside bottom corner.
What is the standard size of a wooden gate?
Since only people are going to be walking through, they are usually from 32 to 36 inches wide. Their height and material often correlate with the fence they happen to be connected to. Manufactured gate heights are usually 4 to 5 feet, but can also be made higher or lower depending on the fence they're attached to.
How do you keep a large wood gate from sagging?
The easiest way to reinforce a gate is to attach a diagonal brace or tension rod connecting one of the hinges to the corner opposite. This equalizes the tension between each side of the gate.
Should a gate open in or out?
Your gate should always swing inward. Why? You want the gate to move towards private space, not out to the public. Single gate hinges work on either side.
How do you support a large wooden gate?
2:243:38The Keys To Fence Gate Bracing | Prevent Sagging With Proper BracingYouTubeStart of suggested clipEnd of suggested clipBecause if we had the bracing going this way as that gate tries to sag it's just going to try andMoreBecause if we had the bracing going this way as that gate tries to sag it's just going to try and pull the screws the only thing that we have going for us is the strength of the screws.
How do you support a wooden gate?
0:155:37Install wooden gate cable support kit - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo now the turnbuckle is inserted into the little triangle for the corner I'm going to take my screwMoreSo now the turnbuckle is inserted into the little triangle for the corner I'm going to take my screw gun put the triangle into position. And make a pilot hole so that it doesn't break the wood.
How do you make a wooden gate stronger?
0:092:40How To Make A Simple Fence Gate for a 6' Wooden Backyard FenceYouTubeStart of suggested clipEnd of suggested clipNext you want to add a diagonal 2x4 in the middle for some extra stability. You can put it intoMoreNext you want to add a diagonal 2x4 in the middle for some extra stability. You can put it into place and then use your square to mark where it should be cut and you can cut the end of the diagonal.
How long do wooden gates last?
Although a good wood fence can be constructed that will last for 10-20 years without much more trouble than replacing an occasional warped picket or staining, the gate itself will be the first part of the fence to fail.
What is the correct way to brace a gate?
Hinge Side on Right with Brace running from Top of latch side to bottom of hinge side. Typical on Wooden Gates.
How wide should a gate be for a car?
The gate needs to be a little wider than your driveway entrance. For example, if your driveway measures up to nine feet, six inches, the ten-foot gate will fit best. If your driveway measures between nine feet, seven inches and eleven feet, nine inches, opt for the twelve-footer. And so on up the scale.
How much does a gate weigh?
If you’ve built it right, you’ll probably need two people to lift and hang it in place, so it may weigh anything from 50 to 150 pounds.
How wide should a gate be?
Next, you’ll need to consider the width of the gate. A single gate shouldn’t be built too much wider than 42 inches, or 3.5 feet. The wider your gate, the lower the angle of your cross-brace, and your gate will sag. To ensure your cross-brace’s angle stays greater than 45 degrees, the height of your door has to be greater than the width.
What is pressure treated lumber?
The real difference is that pressure treating adds chemical preservatives to the wood that help it resist rot and bugs. Both options are readily available, although the species may change depending on availability in your area.
What is the cross bracket on a gate?
Cross Brace. One of the most crucial parts of a gate’s design is the cross-brace, which starts from the top corner opposite the hinges ( the free-swinging side of the gate), pointing down to the lower hinged side of the gate. The cross-brace acts just like an enormous shelf bracket that holds the gate’s structure at a 90-degree angle to ...
What do you need to build a wooden gate?
When you decide to build a wooden gate, you’ll need to keep a few things in mind. The first is what your intended purpose is. You may want a purely decorative gate, perhaps to act as an arbor framing your walkway, or a more secure gate that provides access to the yard through a fence.
How wide should a post hole be?
Each hole should be about 6 inches wider than your post. So if the post is 4 inches wide, the hole should be no less than 10 inches wide. After the hole has been dug, pour a few inches of gravel in the hole to help with drainage. Set the post into the hole and fill in around it with concrete.
Can non-ACQ wood turn black?
Non-ACQ can turn the wood black as the fasteners oxidize, which is an ugly detail. Source: Fix.com. When you start selecting the lumber for your gate, look for the straightest possible pieces. An ideal piece is a kiln-dried wood, which has much of the moisture content lowered, reducing the risk of warping or twisting.
What type of wood is used for furniture?
Wood used for furniture and for appearance is often of a hardwood (or Pine) variety. A few examples of these are shown in the picture above. Whitewood Lumber. The most common species of dimensional building lumber (e.g. for framing a wall) is usually one of the following softwoods (also called whitewoods): Douglas-fir.
What is kiln dried lumber?
Most building lumber sold at home stores is kiln dried to some extent. This means that it has to have a moisture content below 19%. This is denoted by a KD-19 tag. KD-19 (Kiln Dried 19%) lumber will have an average moisture content somewhere around 15%.
How big is a heavy duty gate?
Instead, go with a lighter gate there and install heavier weight gates and corrals for your higher traffic and containment areas. Typically a 2-inch diameter heavy-duty gate (for example 12-foot length by 62-inch height and 118 pounds) is best for high containment and high traffic areas while the lighter weight gates are great for the majority ...
Do you need a heavy gate for a farm?
You do no not need the heaviest gate possible in all the areas of your farm or ranch.”. Be smart when purchasing gates and corrals and invest wisely. At the same time, understand which areas of your property require heavier gates and which ones don’t.
How high should a gate be?
The other measurement we require is the height of the gates, an allowance of at least 2″ (50mm) should normally be made for clearances under the gates, but more or less maybe required depending on your circumstances – such as a driveway that slopes away across the opening.
What is the phone number for woodworkers?
If you are in any doubt when measuring up for the gates do not hesitate to give us a call on 01745 362444 or drop us an email to enquiries@woodworkersuk.co.uk for advice.
Can you fit gates with hinges?
To fit the gates to existing built in hinge pins (hooks to build), this assumes that you have the hinges to fit. If you do not have hinges and your hinge pins have recently been built into the pillars then you should source the hinges from the same supplier as the pins to ensure the hinges fit.
