Crankshaft Position Sensor Replacement pricing for various cars
| Cars | Estimate | Parts Cost | Labor Cost | Average Dealer Price |
| 2010 Hyundai Sonata | $233 | $127.98 | $104.99 | $235.48 |
| 2009 Jeep Grand Cherokee | $130 | $25.39 | $104.99 | $132.89 |
| 2015 Volvo S80 | $227 | $121.82 | $104.99 | $229.32 |
| 2015 Lincoln MKZ | $235 | $87.98 | $146.98 | $238.48 |
How much does it cost to replace a crankshaft sensor?
The good news is that a crankshaft position sensor isn’t usually too expensive to replace. The average cost to have this work done at a shop is around $100-$200. However, if you are comfortable doing some basic automotive repairs yourself, you can probably buy a replacement sensor for around $50-$70.
What is the price of a crank shaft sensor?
The crankshaft position sensor is usually the problem since this part of your car is responsible for the ignition timing. The average cost of a crankshaft sensor usually ranges from $115 to $300, with labor costing between $40 and $200, and the parts itself ranging upwards of $150 total.
How much to replace crankshaft position sensor?
The average cost for crankshaft position sensor replacement is between $178 and $226. Labor costs are estimated between $98 and $123 while parts are priced between $81 and $103. This range does not include taxes and fees, and does not factor in your specific vehicle or unique location. Related repairs may also be needed.
How much does a crank position sensor cost?
The crankshaft position sensor is a key part of the engine in your vehicle. The average price of a crankshaft position sensor replacement cost is between $194 and $258, with the labor costs estimated between $104 and $133, while the cost of the parts is generally between $90 and $125.
How much does it cost to get a crankshaft sensor replaced?
The average crankshaft sensor replacement cost is between $150 and $250. However, it's not uncommon for those prices to skyrocket if you have a higher-end vehicle. That's because the labor costs are typically between $90 and $110.
What happens when your crankshaft sensor goes bad?
A failing crankshaft position sensor cannot provide the right information about piston positioning in the engine, causing a cylinder to misfire. This could also occur from faulty spark plug timing, but if the spark plug checks out, then the crankshaft sensor is likely the source.
Can I drive with a faulty crankshaft sensor?
Can I Start the Vehicle with a Bad Crank? If you wonder if it is safe to start your car when the crankshaft goes, the answer is yes if it is the very beginning of the issue. Once the position sensor becomes compromised or if you have symptoms of a problematic crankshaft that you can't ignore, do not drive your vehicle.
How long does it take to replace a crankshaft sensor?
In most instances, this repair should take no longer than one day.
What does a bad crankshaft sound like?
Crankshaft bearing noise is also caused by low oil pressure which damages the bearing surfaces and could eventually damage the crankshaft itself. This type of noise is usually described as a rumbling or thumping sound deep in the engine when accelerating.
How much does a crankshaft cost?
Replacing a crankshaft typically costs between $2,000 and $2,750. It's a labor-intensive job, so the price may vary depending on your vehicle and how complex the work is. On average, most people pay around $2,500 to have their crankshaft replaced.
How do you fix a crankshaft sensor?
0:361:54Crankshaft Position Sensor: How it Works & How to Fix [1 Method Save ...YouTubeStart of suggested clipEnd of suggested clipPosition sensor first carefully remove the crankshaft. Position sensor from the vehicle visuallyMorePosition sensor first carefully remove the crankshaft. Position sensor from the vehicle visually inspect the sensor to make sure it hasn't been contaminated by a leak from another engine component.
Can a crankshaft sensor cause transmission problems?
Recommended Services. Hello - No, the crankshaft position sensor will not affect your transmission at all - except when it fails, and the engine ceases to run.
Where is a crankshaft sensor located?
The sensor is at either the front or the back of the crankshaft, so it's usually located either on the transmission bellhousing or behind the crankshaft pulley. There should be a small air gap, usually about a millimeter or two, between the sensor and the reluctor.
How many crank sensors does a car have?
Generally, there are four types of crankshaft or camshaft position sensors: magnetic pick-up coils, Hall-effect sensors, magneto-resistive element (MRE) sensors, and optical sensors.
What causes a crankshaft position sensor to fail?
There are a few things that can cause the crankshaft position sensor to fail, including damage, debris and faulty circuitry. Even for modern electronics, the engine is a violent and destructive environment. Though built for this, most sensors eventually succumb to the ever-present heat and vibrations of the engine.
How do you diagnose a bad crankshaft position sensor?
0:272:28SYMPTOMS OF A BAD CRANKSHAFT POSITION SENSORYouTubeStart of suggested clipEnd of suggested clipIt will typically be on the lower side of the engine on the back or the front side. So the firstMoreIt will typically be on the lower side of the engine on the back or the front side. So the first symptom of a crankshaft. Position sensor is the engine. Light. If you have an engine light in your car
How to tell if crankshaft sensor needs replacing?
The crankshaft position sensor will usually let you know when it needs replacing. The Check Engine warning light will illuminate and you may notice that your vehicle has a hard time starting or running smoothly. When you notice any of these signs, schedule an inspection.
Why is my crankshaft position sensor leaking?
Damage to the crankshaft position sensor is sometimes caused by leaking oil, which means there may be another component of your vehicle that needs replacement or repair. The electrical connector can also be damaged, and should be inspected every time the position sensor is replaced.
