What should the voltage be at the remote turn on wire?
While in the ON position, there should be 12+ volts at the remote turn on wire. If you have 12+ volts while the ignition is OFF, the remote turn on wire is connected to constant power.
How do you wire a car radio remote turn on?
Simply connect another piece of blue primary wire to the blue wire in the wiring harness and run the primary wire back to the amplifier to terminate in the remote turn on terminal. To connect wire to wire, an appropriately sized butt connector or other style connector can be used.
What wires do I need to connect a car stereo?
Most car stereos will require the following connections: The power wire coming from the stereo is usually red, and likely will connect to a red wire from the car. The ground wire for the stereo will be black, as will its corresponding wire from the car.
What color is the ground wire on a car stereo?
The ground wire for the stereo will be black, as will its corresponding wire from the car. If there is no ground wire, you can secure the ground cable to bare metal in the body of the car to serve as a ground.
What is the 12V accessory wire on a car stereo?
The 12V accessory wire is one of the three power wires a car stereo utilizes. It is red in color and helps trigger the stereo to come on. However, for this wire to turn on the stereo, your ignition key must be in the accessory position.
Can you use any wire for remote wire?
Just run the remote wire off your other amp. any copper wire will work it doesnt matter how old or new it is. just find some old copper wire and use it.
What gauge is a remote wire?
100-FEET (30.5m) [ BLACK 14 GAUGE PRIMARY OR REMOTE WIRE ] - The lower the gauge number, the thicker the wire. Thicker wire presents less resistance to current flow.
What is remote out wire on car stereo?
0:205:02What is an Amplifier Remote Turn-On Wire? - YouTubeYouTubeStart of suggested clipEnd of suggested clipNow the blue with the white stripe is always typically your remote wire which is a 12-volt turn-onMoreNow the blue with the white stripe is always typically your remote wire which is a 12-volt turn-on to turn on an amplifier some radios.
Can I use remote wire for speaker wire?
Speaker wires can be used as remote wires. It doesn't matter what kind of wire you use for a remote wire. Any copper wire will work when used as a remote wire. Since most speaker wires are made of copper metal, they can be used for remote wiring.
What size wire is remote wire on amp?
AudioControl recommends 18 gauge wire for our car audio products, such as our line converters, EQs, crossovers and DSP processors.
Does the remote wire power the amp?
When the ignition of the vehicle is turned off, the remote turn on wire stops transferring voltage and the amplifier turns off. If the remote turn on wire is connected to a wire in the vehicle that has constant voltage, the amplifier will always be on.
How do I turn on my amp without remote wire?
1:302:51How Can I Turn On My Amp Without Remote Wire? | Car Audio Q & AYouTubeStart of suggested clipEnd of suggested clipFrom your ignition switch to your amp that will turn the amplifier on and off with the key. Or yourMoreFrom your ignition switch to your amp that will turn the amplifier on and off with the key. Or your radio might depending on the vehicle.
What color is the REM wire?
Wiring Harness Color StandardsWire ColorWire FunctionRedSwitch / AccessoryBlackGroundBlueAntenna RemoteBlue with White StripeAmplifier Remote Turn-on10 more rows
What fuse can I connect my remote wire to?
You should be using a fuse tap that will add a fuse for the remote turn on wire in addition to the OEM fuse on the circuit. A 1 amp fuse is enough for your remote lead.
Can you run remote wire with RCA?
You can run the remote wire right along the RCA's.
What Are Key 1 and Key 2 wires?
These radios' SWC wires are often identified as KEY 1 and KEY 2, or SW 1 and SW 2. This enables you to connect your Panasonic, Android radio, or another radio brand to our PAC interface to retain steering wheel controls with the radio without having to modify our 3.5mm connector.
What happens when there is no voltage on a remote?
Literally, the output is not even connected to the source. When voltage is applied to the remote lead, the switch is activated and the output is connected to the source.
How many terminals are there in a relay?
A relay is simple. Basically it's a switch that is activated when there is voltage on the input terminal. There are normally 4 terminals on a relay: +12v (source), remote, ground and +12v (output). You have a good +12v source connected to it, and a remote type lead connected to it.
Can you run an amp wire from a car?
As long as there is enough voltage there to turn on the amp it should be fine. You can even just run a wire from any power source in the car to a switch, then from the switch to your amp's remote and use that to turn it on/off. Doesn't have to be the remote wire.
How to wire a car stereo?
To wire a car stereo, start by disconnecting your car battery to avoid electrocuting yourself. Then, match the colored wires of your radio and your car and twist the wires together . If your car requires an output converter, connect this as well so your radio will work with your car.
What color is the ground wire on a car stereo?
The ground wire for the stereo will be black, as will its corresponding wire from the car. If there is no ground wire, you can secure the ground cable to bare metal in the body of the car to serve as a ground. The 12 volt constant power wire is usually yellow or blue, though it may be a number of colors coming from the car.
Why use a wiring harness clip adaptor?
Using the adaptor greatly reduces the chances that you will make a mistake wiring in your new stereo. Identify and connect loose wiring. If you are not using a wiring harness clip adaptor, you will need to identify the wires coming out of the stereo, as well as those coming out of the car.
How to connect a new stereo to a car?
Your new stereo will come with a diagram indicating what each wire is and what it needs to be connected to, but that process can be made much simpler by using a wiring harness clip adaptor. These adaptors are made to make it easy to connect your new stereo to the car’s existing clip.
How to solder two wires together?
Soldering two wires together requires a soldering iron and solder. You melt the solder onto the wires to stick them together and as the solder cools it form s a permanent bond. Twisting wires together and then covering them with heat-shrink wrap or electric tape will suffice for car stereos.
What to do if you encounter resistance on a stereo?
If you encounter resistance, do not force the stereo in any further. Instead remove the stereo and identify what was in the way, move it, and attempt to slide the stereo in again. As you slide the stereo into place, wires may snag or plastic brackets may come out of place.
How to determine what method your car uses to secure the stereo?
In order to determine what method your car uses to secure the stereo, you can consult your car’s repair manual or look closely once you’ve gotten the trim out of the way. Spring clip mounts may not require the removal of any trim pieces and can be identified by the matching pairs of holes on either side of the stereo.
What is the blue wire on a radio?
Some decks have 2 blue wires, one only sends a signal for the antenna to go up when the actual radio is on. The other is a remote turn on. Usually solid blue for antenna and blue with a white stripe for remote turn on.
What color wires do radio antennas have?
Some decks have 2 blue wires, one only sends a signal for the antenna to go up when the actual radio is on. The other is a remote turn on. Usually solid blue for antenna and blue with a white stripe for remote turn on. May 7, 2012. #4.
