How many camshaft position sensors are there?
fourA camshaft sensor determines the exact position of your engine's camshaft, helping your car keep your engine's combustion running smoothly. Many modern engines have one camshaft sensor for each camshaft. This can mean up to four, although some cars will only have two.
Where is the cam sensor located on a 2004 Nissan Maxima?
0:4611:15Nissan 3.5 Cam Sensor " How to replace them! " - YouTubeYouTubeStart of suggested clipEnd of suggested clipTake a small screwdriver you see the green tab. You want to press that down go up on the connector.MoreTake a small screwdriver you see the green tab. You want to press that down go up on the connector. Okay you're gonna see the lock stays down okay once you have that lock.
How many crankshaft position sensors are in a Nissan Maxima?
There are two crankshaft position sensors on this engine: one at the front of the engine by the crank pulley, and the other at the flywheel area. One sensor detects the 1 degree signal of the sensor, and the other the 120 degree "top dead center"position.
Where is a camshaft sensor located?
The Camshaft Position sensor is typically located in the cylinder head of the engine and has a cylindrical portion that inserts into the head. The Crankshaft Position sensor is normally located in the timing cover or on the side of the block with a cylindrical portion that inserts into the block.
How many camshaft position sensors are in a Nissan Maxima?
The Maxima has 2 of them; the right and the left one. Both are on the right side of the engine. Locate them before you start working on them.
Where is the bank 1 camshaft position sensor?
1:507:39Replacing Bank 1 Camshaft Position Sensor On 350Z - P0340 - YouTubeYouTubeStart of suggested clipEnd of suggested clipIf you look back right here that connector right there that's the cam chef there's a sensor so likeMoreIf you look back right here that connector right there that's the cam chef there's a sensor so like I said we're right behind the engine.
Where is the crankshaft sensor 2004 Nissan Maxima?
The crank sensor is located at the bottom center of the engine just below the flywheel area.
Where is the crankshaft sensor on a 2005 Nissan Maxima?
0:304:08Crank Sensor Replacement 2005 Nissan Maxima - YouTubeYouTubeStart of suggested clipEnd of suggested clipItself. So I'll just note also that the crank sensor is located on the bottom of the motor next toMoreItself. So I'll just note also that the crank sensor is located on the bottom of the motor next to the exhaust.
What causes P0335 code?
What the P335 code means. The P0335 DTC is set once the powertrain control module (PCM) fails to detect proper sensor operation from the crankshaft position sensor. This causes the Check Engine Light to be displayed on the dashboard and a failsafe mode enabled.
How many camshafts does a car have?
An i4 DOHC engine has two camshafts, while a V6 or V8 DOHC engine has four camshafts. Overhead-cam engines have three to five valves per cylinder, but usually two intake valves and two exhaust valves. Older engines and a few newer “pushrod” engines have a single camshaft in the cylinder block.
How long does it take to replace a camshaft sensor?
Replacing a camshaft position sensor typically takes between one and two hours. However, this may vary depending on the make and model of your vehicle.
Is it easy to replace a camshaft sensor?
1:173:33How To: Replace a Camshaft Position Sensor - YouTubeYouTubeStart of suggested clipEnd of suggested clipMay be easiest to remove and replace the camshaft sensor from under your vehicle.MoreMay be easiest to remove and replace the camshaft sensor from under your vehicle.
Steps
Verify that your car (if it isn't a Nissan Maxima 2004) even has one (or more). The Maxima has 2 of them; the right and the left one. Both are on the right side of the engine. Locate them before you start working on them.
Tips
When this happens, it may end up happening to all of the sensors. If you can, replace them both. If not, be prepared for when/if it does happen.
About This Article
wikiHow is a “wiki,” similar to Wikipedia, which means that many of our articles are co-written by multiple authors. To create this article, volunteer authors worked to edit and improve it over time. This article has been viewed 45,902 times.
Duralast WK Camshaft Position Sensor CMKDL2366
Notes: Manual or 4 speed automatic transmission. Contains all Camshaft and Crankshaft position sensors for the vehicle PRICE: 186.99
Duralast Crankshaft Position Sensor CMKDL2367
Notes: 5 speed automatic transmission. Contains all Camshaft and Crankshaft position sensors for the vehicle PRICE: 164.99
Hitachi Distributor CPS0005
Notes: Left, Built from 08/2004. Connector gender: Male. Original OE Part PRICE: 68.99 Terminal Gender: 3 Blade Male Color: Black Terminal Type: 3 Blade Male Connector Gender: 3 Blade Male Connector Shape: 3 Blade Male
Hitachi Camshaft Synchronizer CPS0008
Notes: Right, Connector Gender: Male. Original OE Part. Built from 08/2004
