How do you calculate slate Batten gauge?
The batten gauge can also be calculated using the formula Batten gauge = (length of slate-headlap)/2. The holing gauge can be calculated as Holing gauge = batten gauge + headlap + 10mm. The most commonly used slate size in Southern England is 500x250mm and 400x250mm in Scotland and the North of England.
How do you calculate slate holing gauge?
The holing gauge can be calculated as Holing gauge = batten gauge + headlap + 10mm. The most commonly used slate size in Southern England is 500x250mm and 400x250mm in Scotland and the North of England.
How do you measure slate for roofing?
Batten gauge = (length of slate-headlap)/2. Holing gauge = batten gauge + headlap + 10mm. The most commonly used slate size in Southern England is 500x250mm and 400x250mm in Scotland and the North of England.
What size slate do I need for my pitch?
The most commonly used slate size in Southern England is 500x250mm and 400x250mm in Scotland and the North of England. Most stock slates will be pre-holed at 75, 90 or 100mm, allowing you the versatility of different pitches – commonly 25 degrees in moderate exposure zones and 30 degrees in severe exposure zones.
How to calculate batten spacing?
How to find holing gauge?
How far apart should battens be?
About this website
How is batten gauge calculated?
Measure from the top of the lowest batten to the top of the highest batten, then divide this number by the maximum gauge recommended by the manufacturer, and round this up to the nearest whole number.
How do you calculate roof battens?
Deduct the length of the gutter overhang and the length of the nib from the length of the tile. For example, if the tile has a length of 16 inches, the overhang is 3 inches and the nib is 1 inch, the result is 12 because 16 - 3 - 1 = 12. This is the distance to the next batten.
How do you calculate batten spacing for roof tiles?
1 Measure distance between top of eaves batten and top of ridge batten. 2 Divide distance by maximum gauge of tile being used. 3 Round figure up to give number of courses up slope as a whole number. 4 Divide measured distance by number of courses to give batten gauge.
How much batten do I need for a slate roof?
Slates should always be installed double lap. Concrete slates require 38x25mm batten for 450mm joist spans and 50x25mm batten for 600mm joist spans. Timber shingles and shakes will need a timber batten size of 38x25mm for spans up to 450mm, and 50x25mm for 600mm spans.
How do you calculate the number of battens?
Take your total wall length and divide that by the approximate spacing you would like between the battens. That number will be how many spaces you have on your wall. Add 1 to your number of spaces to get the number of battens on the wall.
How do I know what gauge my roof is?
Setting Out up the roof (Gauge) Measure the distance (A) from the first, eaves course batten to the top course batten. Divide this distance by the maximum tile gauge. Round the answer up to the nearest whole number (B) – this gives the number of tile courses required. Divide A by B to determine the actual batten gauge.
How far apart should roof battens be?
Each product has different requirements, for example, batten spacing for (0.42BMT) corrugated metal roofing needs to be no more than 1100 mm apart, but batten spacing for 0.48BMT metal roofing can be up to 1600 mm apart.
What is batten spacing?
Battens should be fixed to rafters set at centres not more than 600mm apart. They should span at least three rafters and be at least 1.2m long. No more than one in four battens should be joined over one truss for gauges over 200mm.
How far apart are battens?
Typically, batten are spaced anywhere from 12” to 24” apart. I think it looks best to space them as close to 18” as possible, but that's just a personal preference. Our wall is 164” wide, so we used 8 batten (for a total of 7 spaces) with a distance of 19.42 inches between each batten.
What size should battens be?
A true batten is 2-inches in width or smaller, but you can use larger widths by installing trim in place of a batten if you want a thicker appearance.
Do I need to counter batten a slate roof?
Firstly, you might not need them because of the way your roof structure is built. If the layer of breathable membrane is draped across your roof pitch in such a way that it creates gaps between each rafter,it enables water to run out beneath the tiling battens – meaning that there is no need for counter battens.
How to Calculate Meters of Roof Battens Required | eHow
Roof battens are strips of wood or plastic that form the base to which you connect roof tiles. Because the battens raise the tiles up by a small amount, they provide some ventilation. Battens also may help with drainage when water leaks under the roof if they are not made of a material that will absorb water.
How to Calculate Roof Batten Spacing | Roofing Megastore
Battens play a key role in any pitched roof structure. As the supporting base for your roof tiles or slates, it’s critical that your battens are installed correctly to ensure a safe, durable, and aesthetic finish. The first step in doing so is figuring out what roof batten spacing you need.
What Are Roof Battens?
Roof battens are lengths of wood that are fixed along the trusses of a roofing structure to form a base on which roof tiles can be hung. As well as providing a robust anchor point for the nailing of slates and tiles, battens can also help to increase ventilation and weather resistance, reduce ice damming, and even reduce heat loss and gain.
How to Calculate Batten Spacing for Roof Tiles
There’s no question that working out the right roof batten spacing is a critically important step, whether you’re building a pitched roof on a new build, or finishing off a refurbishment project by tiling the roof.
How Many Metres of Battens are Needed?
To ensure you have enough battens to cover the square metreage of your roof, you’ll also need to calculate the total length of batten material required. You can do so by following this easy method:
How to Calculate Batten Spacing for Other Kinds of Roof
Calculating the batten spacing for roof slates is thankfully quite easy. Simply use the formula below:
Conclusion
And that’s how you calculate batten spacing! Although it may seem simple, it’s worth taking the time to do this carefully, and double-check your work, as getting the wrong distance between battens can severely affect the aesthetics and longevity of your new roof.
How to calculate batten spacing?
Similarly, how do you work out Batten roof spacing? 1 Measure distance between top of eaves batten and top of ridge batten. 2 Divide distance by maximum gauge of tile being used. 3 Round figure up to give number of courses up slope as a whole number. 4 Divide measured distance by number of courses to give batten gauge.
How to find holing gauge?
Batten gauge = (length of slate-headlap)/2. Holing gauge = batten gauge + headlap + 10mm.
How far apart should battens be?
Typically, batten are spaced anywhere from 12” to 24” apart. I think it looks best to space them as close to 18” as possible, but that's just a personal preference.
