How do you wind Ansonia mantel clock? To wind the clock simply place the key, or crank, into the winding point and turn clockwise sixteen revolutions. When the clock is fully wound an internal mechanism will prevent you from winding any further.
Full Answer
Do mantel clocks need Side Access?
As for modern wall clocks and pendulum style mantel clocks, he said “These rarely have side or top access, but if you’re vigilant and mechanically inclined you could do the work yourself.
How do you wind a clock with 3 arbours?
Clocks with three winding arbours chime on the quarter-hour making a musical tone. On a clock with three arbours, the centre arbour winds the time train and the left arbour, the strike side and the right, the chime side. On some clocks, there is a smaller hole on the clock face near or above the 12 o’clock position.
Which way do you turn a clock to wind it?
I recommend wearing cotton gloves to preserve the finish of the case. Next, turn the key clockwise. If it will not turn clockwise, turn counterclockwise. Yes, some clocks wind clockwise and some counterclockwise. Do not force the key; wind it with minimal force and wind the arbour until it winds no further.
How do you wind a tall case clock with weights?
On older tall case clocks with weights concealed behind an access door, open the door to observe the weights rise as you wind the clock. As the weights rise to the top, slow down the winding and stop when the weights meet resistance.
How do you wind an Ansonia mantle clock?
0:034:57Ansonia clock gong reset. - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd then clockwise on the right hand side so that one goes around that. Way. Right that should do usMoreAnd then clockwise on the right hand side so that one goes around that. Way. Right that should do us.
How do I wind up my mantle clock?
Unjamming the strike mechanism is quite easy. Gently move the minute hand of your clock counterclockwise by a few minutes. You will likely hear the clock strike, and the mechanism has released. You can then proceed to wind and set your clock as your normally would.
How do you wind a clock with two key holes?
3:379:11How to Properly Wind a Key-wound Bracket/Mantle Clock | ItzAnthonyYouTubeStart of suggested clipEnd of suggested clipSo you just stick the key in see just like that. You might have to twist a little bit but eventuallyMoreSo you just stick the key in see just like that. You might have to twist a little bit but eventually it'll go in and now you just go like this. And all you get just turn it clockwise.
What are the three winders on a mantel clock?
The center winder is for the timekeeping, the right winder is for the quarter-hour chime, and the left winder is for the hour strike.
How do you wind a session on an antique mantel clock?
0:475:23Winding The Sessions Mantle Clock + Tutorial - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou would insert your key in here. And turn it ever so slightly not like ever so sloppy a bit likeMoreYou would insert your key in here. And turn it ever so slightly not like ever so sloppy a bit like you know a little about a quarter of a turn maximum. Then wait 24 hours and check the time.
Why does my clock have 3 winding holes?
Clocks with three winding arbours chime on the quarter-hour making a musical tone. On a clock with three arbours, the centre arbour winds the time train and the left arbour, the strike side and the right, the chime side. On some clocks, there is a smaller hole on the clock face near or above the 12 o'clock position.
Which side of a wind up clock is the chime?
In clocks with more than one keyhole, the left-most hole usually controls the hourly chime, and in clocks with three keyholes, the center keyhole is typically for the quarter-hour chime, although again this can vary from model to model.
Do you stop pendulum to wind clock?
Can I wind my clock when the pendulum is moving, or should I stop it before winding? You can wind your clock when the pendulum is moving. It doesn't matter either way. I accidentally moved the hour hand on my clock, and now it won't keep correct time.
Which winding hole on my clock does what?
The middle hole will wind the spring that powers the timekeeping function of the clock. The right hole, as you're looking at the clock, powers the chimes of the clock. Finally, the left winding hole, as you're looking at the clock, powers the hourly strikes of the clock.
How often do you have to wind a mantel clock?
Most mantle clocks have an eight day movement, which require winding once a week. Using a smooth action, turn the arbor until the springs are fully wound. (Some people do not like winding the clock fully as the fear they may over wind the spring, but this cannot happen.
How do you wind a clock spring?
3:179:16Chapter 13 - Mainspring and Spring Winder - YouTubeYouTubeStart of suggested clipEnd of suggested clipDirection. With one hand on the winding handle cup your other gloved hand over the top of theMoreDirection. With one hand on the winding handle cup your other gloved hand over the top of the mainspring. And slowly wind the spring until the c-clamp comes loose.
The History of the Antique Mantel Clock
Mantel clock (around 1800) by Julien Béliard, Paris, maître horloger recorded on the rue Saint-Benôit and rue Pavée in 1777, still active in 1817, or Julien-Antoine Béliard, maître horloger in 1786, recorded on the rue de Hurepoix, 1787–1806. (Credit: Wikimedia)
Types of Antique Mantel Clocks
A quick way to identify antique mantel clocks is by understanding the different types. Long before manufacturers started leaving signatures on their products, they had unique styles. Experienced collectors can tell a brand by looking at the design, and now you would too.
Identifying Antique Mantel Clocks
At this point, you should have sufficient knowledge of antique clocks, so identifying one should be a piece of cake. But there are a few more hurdles to jump. Once you study the fine print, you’ll assess an antique mantel clock like a seasoned collector.
Antique Mantel Cocks Value Guide
Now to the final step in your training – how do you know when to bid higher or fold? Antique mantel clocks sell between $100-$10,000 depending on certain qualities.
Concluding Thoughts
Please give yourself a round of applause; you made it to the guide. You can identify and value antique mantel clocks now. Before you go, let’s refresh your memory with a few key points;
How to wind a mechanical clock?
Winding your mechanical clock. If the dial is covered by a glass door, open it to access the face. Insert the key into one of the winding arbours and with your non-dominant hand, steady the case while you wind the clock. I recommend wearing cotton gloves to preserve the finish of the case. Next, turn the key clockwise.
How to keep brass finish on clock?
Wear cotton gloves to steady the weights while they are being pulled up to preserve the brass finish on the weight shells. For those clocks that wind with a crank key, insert the key into each winding hole on the clock face and crank slowly till the weights reach the top .
What is the arbour on a clock?
On a clock with three arbours, the centre arbour winds the time train and the left arbour, the strike side and the right, the chime side. On some clocks, there is a smaller hole on the clock face near or above the 12 o’clock position. It is also an arbour but a smaller one used for regulating the speed of your clock.
Why do clocks have two ends?
Two ends are required because the speed adjustment arbour is smaller than the winding key arbour.
What is the hole in the clock on the Ingraham clock?
The smaller hole in the loop end of the “2” on the number 12 is for regulating the clock.
How many half turns does an 8 day clock need?
An 8-day clock usually requires 14 half turns of the key as the arbour does one complete turn per day. Mainspring ratchet and click. The ratchet locks the spring in place during each wind of the key. Allow the key to gently rest back onto its click.
What is a winding arbour?
Each winding arbour has a function. The number of winding arbours corresponds to the number of gear trains (or sets of gears) on a clock. For example, if there is one hole it is a time-only clock; 2 holes mean that it is a time and strike clock, that is, it strikes the appropriate hour on ...
How to clean a pivot point?
Then using a very sharp, thin pivot cleaning stick (barbecue sticks can also be used) scrape out any dried oil and dirt that has collected in and around the pivot points.
Can you use synthetic oil on a clock?
They could even stain dials and are not recommended. As for the right kind of oil, there are a number of excellent brand name synthetic clock oils available on the market today. They protect your clock from wear and tear and tend to stay where put. So it’s best to use them and keep your clock happy.
Does servicing your own clock void warranty?
Before you do anything: If you have a newer clock that’s still covered under the manufacturer’s warranty, be sure to check with them first beforehand, since servicing your own clock could void the warranty.
