Just plug it in and the Watchdog alerts you with an audible alarm when it detects water or near-freezing temperatures. Just plug it in and get started! Setup's a snap using a WiFi capable device, like your smartphone. Connect to the Watchdog with any WiFi-capable device, like your smartphone, and complete the easy-to-follow setup.
How do I Turn Off the alarm on the basement watchdog?
On the Basement Watchdog Emergency slide the switch, located on the front panel, to the left. Please note that not all alarms can be silenced if immediate attention is required.
How do I connect my basement watchdog system to another device?
There are 2 ways to connect: 1 Basement Watchdog CONNECT® and the USB Data port – plug your Basement Watchdog Backup or Combo system in to one of the... 2 Remote Terminal – pair of dry contacts can connect to existing security systems, auto dialers or other external devices More ...
How do you silence a big dog alarm?
On the Big Dog, Special, and Big Combo systems press and hold the reset button continuously for approximately 5 seconds to silence the alarm for 24 hours. On the Basement Watchdog Emergency slide the switch, located on the front panel, to the left.
What parts do I need to purchase for my watchdog system?
All Watchdog systems include the pump, monitoring/charging controller, fluid sensor, float switch, and battery box. You will need to purchase the matching battery and acid. Any additional parts needed for installation, (i.e. check valves and pipe) are listed on the box, brochure and in the manual.
How do I turn my water alarm off?
0:000:15How to turn off a leak alarm - YouTubeYouTubeStart of suggested clipEnd of suggested clipSimply. Pick it up. Off the probes at the bottom and that will stop the alert the lake alarm did notMoreSimply. Pick it up. Off the probes at the bottom and that will stop the alert the lake alarm did not go off you can take the 9-volt battery out from the side right here.
How does a high water alarm work?
0:083:18How to Use a High Water Alarm - YouTubeYouTubeStart of suggested clipEnd of suggested clipWhen the pumps float sends a signal to start injecting water into the lake. If it fails then there'sMoreWhen the pumps float sends a signal to start injecting water into the lake. If it fails then there's another float. And when that switch clicks it's a high it's a high water level float.
How do I turn off my watchdog sump pump alarm?
To permanently disable the water fluid low alarm, attached the fluid sensor rod to the positive terminal of the battery. This can be done by tightening down the wing nut on top of the positive terminal and the fluid sensor.
What is a watchdog alarm?
The Basement Watchdog High Water Alarm (Model BWD-HWA) gives you an early warning system that will save thousands in cleanup and repairs by heading off a drip that started under your sink, a broken fridge water line, or a water heater that sprung a major leak.
Why is my basement watchdog beeping?
If you Basement Watchdog battery alarm won't stop first make sure that there is nothing wrong with your pump system and there is no risk of a flood. After that check the power connection for the pump and battery back up as well as fill the unit to make sure it is not overheating or too cold air and at risk of freezing.
How does sump pump alarm work?
A sump pump alarm helps you know when the water is too high in your basement or crawl space sump pump system, making it difficult for your pump to remove the water effectively. The alarm typically rests on top of the sump pump, and when it gets wet, it beeps like a smoke alarm.
How do I stop my sump pump from beeping?
If you just had a power outage and your backup sump pump was running, the alarm may go off temporarily until power is restored and it can recharge. If this is the case, some battery backup systems have a button to reset the alarm for 24 hours.
How do I reset my sump pump alarm?
How to Reset a Sump PumpLocate the reset button on the motor. If there isn't one, locate the on/off switch and turn it off, or unplug the pump directly from the electrical outlet.Look inside of the sump pump. ... Plug the pump back in or move the switch back to the on position if there was no reset button.
Why is my sump pump ringing?
This usually means your pump is not working because a) it is not receiving any or enough power or b) your pump is old, has worn out, and needs to be replaced. Your pump alarm goes off when it senses water which can also be, more rarely, that you have some sort of plumbing leak which has triggered the alarm from above.
How do you test the watchdog water alarm?
0:592:39The Watchdog Battery Operated Water Alarm - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou have water backing up now the alarm is quite loud it's hotter 10 decibels. And you can hear itMoreYou have water backing up now the alarm is quite loud it's hotter 10 decibels. And you can hear it when we place it into this small dish of water with food coloring.
How do I turn on my watchdog timer?
Click the Start menu and then choose Control Panel. In the Windows control panel, select the System and Security category, and then click RTX64. Click Configure the RTSS Subsystem > Configure the Watchdog Timer.
What is watchdog process?
The Watchdog process launches and monitors the central logger, system manager, and connectors. The core components include the configuration directory, command-line utilities, system manager, and the central logger.
Watchdog Water Alarm teardown
Today we have a somewhat vintage teardown. Even though you can still buy this Watchdog BWD-HWA Water Alarm in home stores and online, the design itself probably goes quite a few decades back as we’ll see below. We’ll also learn a few things about low power design. Rumor has it these last forever on a nine volt battery!
The electronics
Not much in here and sure looks like the eighties! A single sided FR-4 board, one CD4069 (CMOS Hex Inverter), 2N7000 NMOS FET and a few jellybeans is all it takes to drive a very loud buzzer. The bare board is made on week 17 of 2015.
Conclusion
The design is simple and pretty clever with essentially no battery drain until triggered. I am a bit apprehensive about Q1’s gate going directly into the outside world with only a cap across- I’d prefer a series element or a clamp. There is no battery low indicator, but at such a low drain it will take years for the battery to need replacement.
How to disable water low alarm?
To permanently disable the water fluid low alarm, attached the fluid sensor rod to the positive terminal of the battery. This can be done by tightening down the wing nut on top of the positive terminal and the fluid sensor.
What is the pump on a basement watchdog?
All Basement Watchdog primary pumps come with the pump itself, controller with dual float switch, and a stainless steel hose clamp.
How does a float switch work?
The float switch will turn on the pump when the water raises either float, and it will remain running as long as the water is above the float. When the water drops below the float switch, an internal timer in the control unit will keep the pump running to empty the rest of the water in the pit.
What are the parts of a watchdog?
All Watchdog systems include the pump, monitoring/charging controller, fluid sensor, float switch, and battery box. You will need to purchase the matching battery and acid. Any additional parts needed for installation, (i.e. check valves and pipe) are listed on the box, brochure and in the manual. back to top.
How long does it take for a Big Dog alarm to silence?
On the Big Dog, Special, and Big Combo systems press and hold the reset button continuously for approximately 5 seconds to silence the alarm for 24 hours. On the Basement Watchdog Emergency slide the switch, located on the front panel, to the left.
How long does it take to recharge a basement watchdog?
The charger on the Basement Watchdog Special is a smaller 1.6 amp smart charger and may take 3 days to fully recharge. While the Emergency system is a small .4 amp trickle charger and can take several days to recharge a battery.
Do basement check valves make noise?
Most check valves will make a sound when they close. We suggest the Basement Watchdog Klunkless check valve. It features a silencing air chamber that absorbs the sound that normally occurs after a pump shuts off. Otherwise, make sure your discharge assembly is attached solidly, and the pump is resting firmly on the bottom of the pit.
