How do you use the soap dispenser on a Honda pressure washer? Attach the black low-pressure soap tip to the wand, and connect the pressure washer to your water source. The gallons per minute, or GPM, flow rate of the source should be at least as high as your machine's rating.
How do you clean a pressure washer with soap?
Run water through the system for a couple of minutes by releasing the trigger gun. Place the filter end of the soap tube into the bucket of soap solution, making sure the filter is all the way to the bottom of the bucket. Attach the other end of the soap tube firmly to the injector nozzle on your pressure washer's pump.
How does soap travel through a pressure washer?
Soap solutions travel from the soap solution container through the siphon hose and into the pressure washer wand, where the solution mixes with water and disperses through the tip of the wand.
How do you turn on a pressure washer with a hose?
Push a garden hose into the opening and release the quick connector to fasten the hose in the pressure washer. Turn the garden hose water faucet counterclockwise to turn the water flow on. Press the “On/Off” toggle switch to the “On” position to turn the pressure washer on.
How do you dilute detergent in a pressure washer?
Mix the soap or detergent solution in the bucket using the manufacturer's directions, taking into consideration the water-to-chemical dilution ratio of your downstream injector. This ratio is found in your pressure washer's manual. These are usually fixed at approximately a 10-1 dilution rate.
How do you get the soap dispenser to work on a pressure washer?
Make sure you are using the proper soap siphon setting or nozzle. Refer to operator's manual for correct application. Slowly close the water supply valve while spraying the soap nozzle until suds are visible. Test for blockage: Remove the high-pressure hose from the pump and start the engine.
Why won't my pressure washer pull soap?
Generally, if your pressure washer isn't dispensing soap, it's most likely because the water pressure is too high. This prevents correct suction and mixing. I recommend using a low-angle nozzle. Check the hose and tube for kinks and blockages.
Can you use Dawn dish soap in pressure washer?
You can use Dawn dish soap in your pressure washer, but you need to dilute it properly with hot water. Take 1 tablespoon of liquid dish soap and dilute it in 1-1.5 quarts of hot water. However, the results of cleaning with Dawn dish soap might not be as effective as some special pressure washer detergents.
Do you dilute soap in pressure washer?
Hello from Karcher - yes, most detergents for pressure washers are concentrated - typical dilution is 20 parts water to 1 part concentrated soap and be sure to mix it outside the soap tank first then fill the soap tank.
Why use downstream soap injector?
Using the downstream soap injector to apply the right cleaning solution for the job saves time and labor. The soap tube system is used to deliver the detergent solution directly to the surface to be cleaned, eliminating extra steps and equipment. Advertisement.
What is the recommended dilution rate for soap?
These are usually fixed at approximately a 10-1 dilution rate. If the suggested dilution is 10-1, you can use the product as is. If a 20-1 ratio is recommended for application, you will need to mix half soap and half water.
How to apply detergent to a pressure washer?
Applying cleaning detergents is a very easy process using one of the two following methods. Soap/Detergent tank – If you have a detergent tank attached to the frame of your pressure washer, simply remove the cap from the tank and pour the detergent into the tank. Soap/Detergent siphon hose – If you do not have a detergent tank, ...
Where is the detergent siphon hose?
Soap/Detergent siphon hose – If you do not have a detergent tank, you should have a detergent siphon hose that is attached to the pump housing near the high-pressure hose connection. Simply unroll the hose and place the filter end into your container of detergent.
What nozzle do you use for soap?
Use of any of the other nozzles will cause the pressure to rise higher and the injection valve will not open. Use the high-pressure nozzles to rinse away the soap and grime.
Step 1
Follow the pressure washer detergent package's instructions for mixing with water. Soap solutions usually require dilution for use in a pressure washer.
Step 2
Push the small end of the filter siphon tube into the detergent container so it touches the bottom of the container.
Step 3
Hold the pressure washer wand in one hand and push the nozzle forward with the other hand. This sets the adjustable nozzle on a low-pressure mode for detergent application.
Step 4
Pull the brass quick-connect hose nozzle backward on the pressure washer. Push a garden hose into the opening and release the quick connector to fasten the hose in the pressure washer.
Step 5
Turn the garden hose water faucet counterclockwise to turn the water flow on.
Step 6
Press the “On/Off” toggle switch to the “On” position to turn the pressure washer on.
Step 7
Point the wand at the building, house or other surface you intend to clean, and spray the soap solution from the bottom upward.