How do you use Stanley IntelliSensor?
- Turn on the stud finder.
- Place the stud finder against the wall where you are looking for a stud.
- Slide the stud finder slowly along the wall, moving horizontally.
- Stop moving when the red lights begin to light up, indicating that you are approaching a stud.
How do you use a Stanley intellisensor sensor?
From the Stanley IntelliSensor™ Stud Sensor instruction manual. Hold the IntelliSensor™ Stud Sensor flat against the surface, making firm contact. Locate the activation switch on the right-hand side of the unit – press and hold in. The red LEDs will briefly flash and the green LED “Power” light will go on and remain on.
How do I use the intellisensor™ unit?
Slide the IntelliSensor™ unit slowly across the surface in a straight line. As it moves closer to the stud, red LEDs will go on. When it detects the stud edge, the top LED will go on and an audio tone will sound. Use the handy pencil hole marker on the IntelliSensor™ unit to mark the stud edge.
How do I Turn On my intellisensor™ stud sensor?
Hold the IntelliSensor™ Stud Sensor flat against the surface, making firm contact. Locate the activation switch on the right-hand side of the unit – press and hold in. The red LEDs will briefly flash and the green LED “Power” light will go on and remain on.
How accurate is the intellisensor™?
Utilizing the procedure of scanning and marking from two sides, the IntelliSensor™ unit will find the stud center within 1/8" accuracy for wood and 1/4" accuracy for metal. When measuring a wood stud under 3/4" drywall, it is recommended the IntelliSensorTM to be used at 35-55% relative humidity.
What does a Stanley Intellisensor do?
Stud sensor locates the edges of studs or joists through dry wall and other common wallboard. Works off a 9 volt battery and features automatic shut off. Pencil notch for marking, LED displa and buzzer indicates stud and joist edges.
How do you use an old Stanley stud finder?
How to Use a Stanley Stud FinderTurn on the stud finder. ... Place the stud finder against the wall where you are looking for a stud. ... Slide the stud finder slowly along the wall, moving horizontally. ... Stop moving when the red lights begin to light up, indicating that you are approaching a stud.More items...
How do you use a Stanley stud finder laser?
0:201:28How to Use a Laser Line Level & Stud Finder Tool - YouTubeYouTubeStart of suggested clipEnd of suggested clipNow you'll want to mark both edges of your stud. And then as I move further away that target getsMoreNow you'll want to mark both edges of your stud. And then as I move further away that target gets farther away. Now you always want to double-check your stud by moving in the opposite.
How do you use a stud finder wall scanner?
0:253:38Homder Stud Finder Sensor Wall Scanner Review ... - YouTubeYouTubeStart of suggested clipEnd of suggested clipThere's a button a power button right here okay. And then over on the side it has the Scan button soMoreThere's a button a power button right here okay. And then over on the side it has the Scan button so I'm gonna go ahead and press the power button on.
How do you read a Stanley stud finder?
0:154:29How To Use A Stud Finder Simple Easy - YouTubeYouTubeStart of suggested clipEnd of suggested clipOr electrical wire it also has two indicators one in green and one in red the green one is to letMoreOr electrical wire it also has two indicators one in green and one in red the green one is to let you know that it's ready meaning you can keep holding the button and moving the stud finder around.
How do I know if my stud finder is working?
0:271:09Zircon Tip Minute 5: Avoiding False Positives With Stud Finder When ...YouTubeStart of suggested clipEnd of suggested clipTurn it on and scan vertically along the object. If you get a consistent metal. Reading you'veMoreTurn it on and scan vertically along the object. If you get a consistent metal. Reading you've probably found a metal pipe or conduit if you get no metal reading at all you've.
How do I check a stud center?
One side of the electrical box for an outlet or a switch typically attaches to a stud. Turn off the power to the outlet or switch if you plan to remove the cover and look for the stud. If you can locate the edge of the stud the box attaches to, measure out 3/4 inch to locate the center of the stud.
How do I calibrate my Stanley Intellisensor pro?
Hold the IntelliLaser™ Pro flat against the surface, making firm contact. Press and hold the "ON" button. All indicators on the LCD are displayed while the unit goes through its 1 to 3 second calibration cycle. The word "CALIBRATING" will appear on the LCD (illustration 2) while the unit is calibrating to surface.
What does AC light on stud finder mean?
AC Scan is a dedicated Scan mode on certain MultiScanner ® tools that enables the user to narrow the location of live AC (using the interactive calibration technique). With AC Scan, the display changes to indicate when the tool is moving towards or away from the live electricity.
How do you find studs behind drywall?
1:236:55Find a Wall Stud Without Using a Stud Finder - YouTubeYouTubeStart of suggested clipEnd of suggested clipAll you do is take a tape measure. And from the edge of that outlet box you can take a pencil orMoreAll you do is take a tape measure. And from the edge of that outlet box you can take a pencil or even your nail and you'd measure over inch. And a half you make a little mark.
How far apart are studs?
The general spacing for wall studs is 16 inches on center, but they can be 24 inches.
Step 2
Place the stud finder against the wall where you are looking for a stud. Hold the tool at the height where you plan to drill or nail into the wall. Some studs may slant or jog, which can throw off your calculations unless you are at the exact proper height.
Step 3
Slide the stud finder slowly along the wall, moving horizontally. The red lights on the stud finder indicate the depth of the wall.
Step 4
Stop moving when the red lights begin to light up, indicating that you are approaching a stud. Move slowly back and forth until you have found the point at which most of the lights are lit. A tone will also sound to indicate that you have located the stud.