How do you convert a decimal to a ruler?
To convert a Decimal to a Fraction follow these steps:
- Write down the decimal divided by 1, like this: decimal 1
- Multiply both top and bottom by 10 for every number after the decimal point. ...
- Simplify (or reduce) the fraction
How do you measure meters and centimeters with ruler?
Using Coins and Bills to Measure
- A U.S. bill is 2.6 inches tall x 6.2 inches long (6.6 cm x 15.8 cm).
- Canadian bills are 6 inches long x 2.8 inches tall (15.2 cm x 7 cm).
- A 1-cent coin is .75 of an inch (2 cm) across.
- A quarter is just under 1 inch (2.5 cm) across.
What do the numbers on a ruler mean?
What does a metric ruler measure? A metric ruler is used to measure length. It is divided into units of centimeters. Each number on the ruler represents 1 centimeter. Are mm and CM the same on a ruler? On a metric ruler, each individual line represents a millimeter (mm). The numbers on the ruler represent centimeters (cm).
How many centimeters make an inch on a ruler?
there are 12 inches to a std ruler and 2.54 cm in one inch.therefore the total cm would be 2.54 X 12 = 30.48 or 30 full cm
How do you use a ruler?
1:115:43HOW TO USE A RULER TO MEASURE INCHES! - YouTubeYouTubeStart of suggested clipEnd of suggested clipNotice the large numbers one through six are labeled on the ruler. Each of these spots is a value ofMoreNotice the large numbers one through six are labeled on the ruler. Each of these spots is a value of one inch in length. So the distance between zero and one is equal to one inch.
How do you read decimals in inches?
1:3514:20Read decimal inch rulers (1/10, 1/100, 1/50 inch) - YouTubeYouTubeStart of suggested clipEnd of suggested clipHas been divided instead of 16 parts or 8 parts or 32 64 or 128 parts the whole inch this is oneMoreHas been divided instead of 16 parts or 8 parts or 32 64 or 128 parts the whole inch this is one inch it has been divided. Into ten parts here is a standard ruler next to it.
How do you read a tape measure with decimals?
1:383:39Read an engineers` tape measure (in decimal feet) - YouTubeYouTubeStart of suggested clipEnd of suggested clipFeet or four point nine feet then it's four point 91 92 93 94 4.95 every increment here is 100th ofMoreFeet or four point nine feet then it's four point 91 92 93 94 4.95 every increment here is 100th of a foot which is written as 0.01.
How do you read a ruler?
0:486:18How to Read an Inch Ruler or Tape Measure - YouTubeYouTubeStart of suggested clipEnd of suggested clipIf you count the marks you'll see that there are 16. You can do an easy check count 8 marks and seeMoreIf you count the marks you'll see that there are 16. You can do an easy check count 8 marks and see if you're at the half-inch. Mark.
What is .8 on a ruler?
0:061:28How to Measure in Eighths on a Ruler : Math Measurements - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo that's convenient if you want to measure in eighths because 8 is half of 16. So it'll be easy toMoreSo that's convenient if you want to measure in eighths because 8 is half of 16. So it'll be easy to convert.
How do you read 1.7 inches on a ruler?
0:341:33How to Read a Ruler - YouTubeYouTubeStart of suggested clipEnd of suggested clipStep 3 recognize the different line lengths on the English side of the ruler the inch line is theMoreStep 3 recognize the different line lengths on the English side of the ruler the inch line is the longest line with the number next to it the shorter lines represent fractions of an inch.
What is .62 on a tape measure?
Inch/mm equivalents tableinch/64Fractional inchDecimal inch5959/640.9218756015/160.93756161/640.9531256231/320.9687559 more rows•Mar 28, 2003
Where are Komelon tape measures made?
Ltd. (hangul:코멜론주식회사, KRX: 049430) is a Korean chemical, machinery, tool and engineering company, headquartered in Busan, Korea. Established in 1963, it manufactures plastic and steel tape measures, level gauges and other tool products.
Where is 0.75 inches on a ruler?
Fraction, Decimal, and Millimeter Equivalent MeasurementsFractionDecimalMillimeters11⁄16“0.687517.46253⁄4“0.7519.0513⁄16“0.812520.63757⁄8“0.87522.22512 more rows•Feb 11, 2021
What is 1 cm on a ruler?
Each centimeter is labeled on the ruler (1-30). Example: You take out a ruler to measure the width of your fingernail. The ruler stops at 1 cm, meaning that your nail is precisely 1 cm wide. So if you counted five lines from 9 cm, for instance, you'd get 9.5 cm (or 95 mm).Aug 15, 2019
What is the size of ruler?
A standard ruler is 12-inches long and 30 centimeters in length. It is likely your ruler will state “inches” or “cm” to make it easier to tell which side is which. Each of these measurements has a perpendicular line to denote where this measurement falls on the ruler.Jul 5, 2019
How do you measure inches by hand?
The first joint of an index finger is about 1 inch long. When a hand is spread wide, the span from the tip of the thumb to the tip of the pinkie is about 9 inches; from the tip of the thumb to the tip of the index finger, around 6 inches. It's about 18 inches from the elbow to the tip of the middle finger.Apr 13, 1996
How to get decimal point on a document?
If you don’t see the ruler at the top of your document, go to View > Ruler. Click or tap the tab selector on the left end of the ruler until you see the decimal tab . Select on the ruler where you want the decimal point to be. You can click and drag this later to move it.
How to change the time on a clock?
Go to Start > Control Panel > Clock and Region or Clock, Language, and Region. In the Region dialog box, select Formats > Additional Settings. If you don't see the Region dialog, select Region or Change date, time, or number formats in control panel.
How to measure length of a ruler?
To measure a length, put the left end of the ruler, which could be labeled "0" but probably isn't, at one end, and pick the closest mark on the ruler to the other end. Find the closest centimeter mark to the left of your mark. That will tell you the number of whole centimeters (13 in the above example).
What do the shortest lines on a ruler mean?
The next shortest lines (A) represent an odd number of halves of an inch. The longest lines (8 or 9) represent whole inches, and are numbered. The lines labeled 8 and 9 above mark points on the edge of the ruler that are eight and nine inches from the left-hand end of the ruler.
What does the shortest line in fractional rulers represent?
The shortest lines labeled A represent tenths of centimeters, or millimeters. Since 1/2 = 5/10, the B line also represents 5 millimeters. The fractional ruler used twos because those are easy to count; here we have a special mark at 5 for the same reason. In effect, the markings use base 2 and 5 (like Roman numerals).
What are the marks that are the same size?
All the marks that are that size or bigger are eighths: 1/8, 2/8 (which is the same as 1/4), 3/8, 4/8 (which is the same as 1/2), 5/8, and so on. If you want, you can just count all the marks that are the same size, counting by odd numbers: 1/8, 3/8, 5/8, 7/8.
How to change the ruler on a Word document?
If you don't see the ruler at the top of your document, go to View > Ruler to display it. Select Left Tab at the left end of the horizontal ruler to change it to the type of tab you want. A Left tab stop sets the left end of the text line. As you type, the text fills toward the right.
How to indent right side of paragraph?
The right indent marker controls the position of the right side of a paragraph. Select the text where you want set the right indent. On the ruler, drag the triangular marker on the lower right side of the ruler to the place you want the right edge of the paragraph.
How to add hanging indent in Word?
Select the text where you want to add a hanging indent. On the ruler, drag the upper triangular part of the lower marker to the place you want the indentation to start, for example to the 1" mark. If you don't see the ruler at the top of your document, go to View > Ruler to display it.
How to move the left indent in Word?
When you move the left indent, your first line indent or hanging indent are moved in sync. Select the text where you want set the left indent. On the ruler, drag the square marker on the lower left side of the ruler to the place you want the left edge of the paragraph.
What are the two types of scales used in rulers?
There are two types of scales commonly used on rulers; Fractional and Decimal. Fractional Rulers have graduations or marks based on fractions, for example 1/2", 1/4" 1/8", 1/16", etc.. Decimal Rulers have graduations or marks which are based on the decimal system such as 0.1, 0.01, etc.
What is the abbreviation for centimeters?
Centimeters - abbreviated as cm. Millimeters - abbreviated as mm. There are 100 cm in a m and 10 mm in a cm, thus there are also 1000mm in 1 m. In the drawing below we show various options for cm and mm and how to correctly read the ruler; remember 10mm = 1cm and 100cm = 1m.

Reading The Marks
- We can start with an early question and answer (1997) that we regularly used as a reference for students asking about this: Doctor Rob replied: Here is an example of a ruler that combines the two kinds we’ll be seeing:
Naming The Fractions
- Our next answer is from 1999, and just fills in some details in the pictures: I first referred to the answer above, and then added some more detailed diagrams: As Doctor Rob explained, we can count only odd numbers; or we can just count all the lines of at least the length of the one we are reading. This is because all the even numbers correspond to fractions with a smaller denominat…
Measuring An Object
- In 2000, Doctor Ian answered a very similar question with details on how to find the length of an object. The question was this: Doctor Ian first showed a metric ruler: This version lacks the longer line at 5; but we can see here that we are counting millimeters (mm), which are tenths of a centimeter, so that 19 mm is the same as 1.9 cm. After showing fractional rulers as we’ve seen …
Can You Just Count lines?
- The next question, in 2005, called for a still more detailed explanation: Doctor Ian assumed that Mary had read the answers above, and needed more: Here we see just the last inch of the object; the “something” would be the label on the inch mark at the left. Another way would be to just see that it is one small mark (1/16) less than 1/2, and subtract; but that requires work with fractions. …
Why Is It called A Ruler? Isn’T That A King?
- Several of us are interested not only in numbers, but also in words. I find the following fascinating: Doctor Rick answered: English does that too … We still (sometimes) talk about “ruled” paper, meaning it has straight lines drawn on it. Did you notice that the original meaning of ruler was just “straightedge”, without reference to having marks on it? Next time, let’s look at protractors!