Can you use Pro flex gas line inside?
Installation Guide Pro-Flex CSST can supply gas throughout a home or commercial building. Route it through walls, floor or ceiling joists, or outside to a variety of appliances.
How do you ground a pro flex gas line?
0:541:48How to Properly Bond HOME-FLEX CSST - YouTubeYouTubeStart of suggested clipEnd of suggested clipMetal. Then run the minimum six gauge copper wire through the bonding clamp. This wire is thenMoreMetal. Then run the minimum six gauge copper wire through the bonding clamp. This wire is then attached to the homes grounding network via the grounding bus bar in the panel.
How do you connect proflex to black pipe?
1:032:17Pro-Flex CSST Fitting - How To Video (website) - YouTubeYouTubeStart of suggested clipEnd of suggested clipTo assemble the fitting simply slide the nut over the tube with the threaded end pointed toward theMoreTo assemble the fitting simply slide the nut over the tube with the threaded end pointed toward the cut end of tubing. By hand open the split ring wide enough to fit in the fourth Valley.
Does flexible gas line need to be grounded?
FAC does not require bonding. This is because they are connected to a bonded (if properly installed) gas-distribution system. It is between 1–6 feet long. FAC are commonly found between the home's gas-supply lines and the gas equipment OR appliance.
Does Pro Flex need to be bonded?
In accordance with the NFPA 54 Section 7.13, Pro-Flex,® LLC, requires proper bonding of Pro-Flex gas piping systems in a structure to the structure's electrical grounding system. This must be performed by a qualified person recognized by the local jurisdiction as capable of performing such work.
Does proflex Csst need to be bonded?
All new CSST systems must be bonded regardless of whether the systems include only CSST or include other piping materials (steel pipe or copper pipe/tubing) in combination with CSST.
How do you install a flex gas line?
0:261:22How to Install HOME-FLEX CSST Flexible Gas Pipe - YouTubeYouTubeStart of suggested clipEnd of suggested clipAre easy to install. Simply. Cut the pipe along the values of the corrugation. With the home flexiMoreAre easy to install. Simply. Cut the pipe along the values of the corrugation. With the home flexi SST tubing cutter. Remove the sheathing with a blade. And slide on the nut.
Can you use flex pipe for gas?
These extremely flexible pipes are made from stainless steel and often come coated in a trademark yellow casing, though they can sometimes be black. This clever revamp of the traditional black steel pipes allows natural gas to travel to your fireplace, furnace, stovetop, and any other appliances that use natural gas.
What is the black flexible gas line?
Gas Piping Has a New Look… The black conductive jacket of CounterStrike® has been shown to be up to 400 times more resistant to the damaging effects of electrical energy than yellow CSST. It also lays straighter and pulls easier than yellow CSST.
How long can you run a flexible gas line?
Three- or six-foot long and accessible: The flexible connectors can't go through walls, floors or ceilings, nor can they be concealed. The flexible connector length usually is limited to 3 feet except for gas ranges and clothes dryers. For these appliances, 6 feet generally is allowed.Jul 11, 2017Everything You Need to Know about Gas Piping - Carson Dunlophttps://www.carsondunlop.com › training › resources › ev...https://www.carsondunlop.com › training › resources › ev...Search for: How long can you run a flexible gas line?
Where do you bond the gas pipe?
Corrugated stainless steel tubing (CSST) gas piping systems shall be bonded to the electrical service grounding electrode system at the point where the gas service enters the building. The bonding jumper shall be not smaller than 6 AWG copper wire or equivalent.Gas Pipe Bondinghttps://www.mcpcity.com › DocumentCenter › View › Ga...https://www.mcpcity.com › DocumentCenter › View › Ga...Search for: Where do you bond the gas pipe?
Should I ground my gas line?
CSST Gas Lines Must Be Grounded Contact a licensed electrician who will ensure it is properly bonded and grounded. The reason for this safety precaution is that a nearby lightning strike could cause the systems in your structure to become electrically energized.Nov 3, 2015Properly Grounded Gas Supply Lines - Frye Electric, Inc.https://www.fryeelectricinc.com › blog › november › pro...https://www.fryeelectricinc.com › blog › november › pro...Search for: Should I ground my gas line?
Where should the O ring sit on a washer?
Slide the washer/slide ring over the end of the tubing followed by the silicone O-ring. (O-ring should sit in the third valley when properly installed).
How to remove jacket from tubing?
Using a utility knife or scissorstyle pipe cutter, cut through the coating of the tubing just behind the fourth valley and remove the jacket form the tubing.
What is flexible gas line?
A flexible gas line is an ingenious method of supplying natural gas to fireplaces, furnaces, cooktops, clothes dryers and any other gas appliance. Virtually all state and local code authorities permit its use and many contractors are finally embracing it.
How to get opinions on flexible gas lines?
If you have ANY DOUBTS about flexible gas lines or CSST, visit a local firehouse and talk to the team leader that's on duty. Visit SEVERAL firehouses to get different opinions.
What are the Two Gas Line Install Choices?
These are traditional black iron pipes that I installed in 1987. Each end of a piece of pipe must be threaded. It's messy and hard work, but I must admit I sort of enjoy it. The pipe is extremely durable and rarely has a lightning strike cause a fire in a house with black iron pipe. © 20187 Tim Carter
Is it Easy to Install Additional Gas Lines?
Adding additional gas lines at a future date is not a problem if you plan for the possibility during the original installation. The CSST systems can be installed one of two ways:
How Do You Make Soft Copper Connections?
Connections are made with common flare fittings that tighten with standard wrenches. The only specialized tool you need is a flaring tool made to fit the pipe size you are working with.
Can cast fittings leak?
Each of the cast fittings can be the source of a leak. What's more, the threaded joints on both sides of the fitting can also be potential leak points. Because the CSST snakes its way around bends and obstructions as one solid piece of tubing, you only have a fitting at each end of the line.
When was corrugated stainless steel tubing approved for residential use?
This material was approved for residential use in 1988 by the National Fuel Gas Code.
