Method 2: Use a Ball Joint separator
- Loosen the Nut on the Tie Rod End. With a wrench, apply five or six turns. ...
- Apply Lubricants. The separator is 100% steel-bodied. ...
- Place the Ball Joint Separator. Place the concave part of the separator between the boot and tie rod end of the ball joint. ...
- Tighten the Bolt. ...
- Completely Remove the Nut. ...
- Push the joint. ...
What does a pickle fork tool do?
A pickle fork isn't just a long skinny fork you use to take pickles or olives out of a glass jar, it's also a long narrow tapered tool you can use to separate ball joints and tie rod joints. We'll save you the time and hassle; don't just try hammering on a ball joint with a hammer to separate it.Jan 21, 2020
Do you need a pickle fork for ball joints?
Do not use a pickle fork on a reusable part. If you are removing the joint in order to replace or service something else, the pickle fork will only cost you more money. The reason is that you can't save the dust boots, a fork will always rip them. If you are replacing the joint, then it really won't matter.Jun 12, 2021
How do you use a ball joint separator?
0:212:25How to use a Ball Joint Separator - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe next thing we have to do is slide the concave part of the separator between the boot and the tieMoreThe next thing we have to do is slide the concave part of the separator between the boot and the tie rod end it takes a little bit of pressure and it'll clunk into position.
Can you use a pickle fork on a pitman arm?
Manual / Pneumatic Pickle Fork Set Use to separate ball joints, tie rods, and Pitman arms. Set contains two handles: knurled handle allows use of a hammer; smooth handle fits in a pneumatic hammer.
What can I use if I don't have a ball joint separator?
Place your jack directly underneath your axle hub where the ball joint goes down. You can put a piece of wood in between your axle hub and the jack. Then gently raise the hub a bit. Now you should be able to use a hammer to separate the bottom part of the joint from the top.Mar 2, 2021
How do you separate lower ball joints?
2:504:03How to Break a Ball Joint Free - 4 Different Ways - YouTubeYouTubeStart of suggested clipEnd of suggested clipWhile the fork shaped portion pushes against the steering knuckle. The bolt is tightened on theMoreWhile the fork shaped portion pushes against the steering knuckle. The bolt is tightened on the opposite. Side working as a lever to break the taper free.
How do you use a ball joint press on a lower ball joint?
0:178:24How to Press a Ball Joint - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd you can see it sits just like that so this part is the part that it mates with on the bottom ofMoreAnd you can see it sits just like that so this part is the part that it mates with on the bottom of the control arm right here this shoulder to get this out you press it downwards.
How do you use a Repco ball joint separator?
0:081:15Supercheap Auto - YouTubeYouTubeStart of suggested clipEnd of suggested clipUsing a 23 millimeter socket or spanner tighten the ball on the ball separator. Until the ball jointMoreUsing a 23 millimeter socket or spanner tighten the ball on the ball separator. Until the ball joint breaks free it's now safe to remove the castle nut while supporting any control or steering arms.
How do you use a ball joint upper press?
1:1715:45How to Replace an Upper Ball Joint - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo we're gonna have to press it out of the knuckle in order to press it out of the knuckle we needMoreSo we're gonna have to press it out of the knuckle in order to press it out of the knuckle we need to tilt the knuckle. Backwards.
How do you separate steering linkages?
0:101:09Separating Ball Joints and Tie Rod Ends - YouTubeYouTubeStart of suggested clipEnd of suggested clipHit him with a hammer or an air hammer. And they separate the joint.MoreHit him with a hammer or an air hammer. And they separate the joint.
What is a drag link on a car?
A drag link converts rotary motion from a crank arm, to a second bellcrank, usually in an automotive steering system.
How do you remove a drag link from a pitman arm?
The stud is tapered so if you place one heavy hammer preferably a sledge against the side of the piece (knuckle or steering arm which has the tapered hole) and smack the opposite side of the same piece. The force will compress the tapered hole and pop the tapered stud out.Jun 13, 2015
Is It Possible to Remove Ball Joint Without Pickle Fork?
It is quite possible to remove the ball joint without a pickle fork. Some of them are even easier. However, pickle fork is widely used thus we may not know about the others.
How to Remove Ball Joint Without Pickle Fork?
Tie rods are commonly equipped with ball joints that have a taper. Between the control arm and the steering knuckle, it acts as a connector. As soon as the ball joint’s taper comes loose, the ball joint is free.
Frequently Asked Questions
Answer: No, you must remove the entire control arm assembly and give it to a professional or hire a press to do it for you.
Bottom Line
We hope we could provide you everything you need to know on how to remove ball joint without pickle fork. Make sure to follow our instructions well.
