how do you tighten the chain on a poulan electric chainsaw
by Krista Schroeder
Published 3 years ago
Updated 2 years ago
How do you tighten a Poulan electric chainsaw? Loosen the guide bar nuts and turn the adjusting screw counter-clockwise 1/4 turn to loosen the chain if it is too tight. Loosen the guide bar nuts and turn the adjusting screw clockwise 1/4 turn to tighten the chain if it is loose. Tighten the guide bar nuts firmly with the guide bar adjusting wrench or socket wrench.
With a screwdriver. The right tension depends on the chain temperature. If you haven't startedMoreWith a screwdriver. The right tension depends on the chain temperature. If you haven't started cutting yet the chain should fit snug against the guide bar if.
Put on protective gloves, and place the Poulan P3416 chainsaw on a flat, level working surface to gain access the cutting chain adjusting screw. Loosen the guide bar nuts holding the clutch cover to the side of the chainsaw engine with a guide bar adjusting tool or socket wrench.
How do I tighten the chain on my Chainsaw?
Tightening the screw will tighten the chain, and loosening will loosen the chain. Double check the chain to see that it's at the correct tightness before moving on. It is very important to lift the nose of the chainsaw while tightening the nuts that secure the side panel and guide bar (see picture below).
Why is the chain on my Poulan chainsaw so slack?
The cutting chain on your Poulan brand chainsaw heats up and stretches the more you use the chainsaw, and this results in excess slack in the chain. Adjust the chainsaw cutting chain tension before you use the chainsaw and after refueling to keep it operating properly.
How long does it take to tension a chainsaw chain?
Even though tensioning a chainsaw chain is easy and takes less than a minute, it's important to do each step carefully and correctly. Forgetting to do something like lift the guide bar nose when tightening it can seriously affect your tool.
How do you tighten a Poulan electric chainsaw?
Loosen the guide bar nuts and turn the adjusting screw counter-clockwise 1/4 turn to loosen the chain if it is too tight. Loosen the guide bar nuts and turn the adjusting screw clockwise 1/4 turn to tighten the chain if it is loose. Tighten the guide bar nuts firmly with the guide bar adjusting wrench or socket wrench.
And a half inch socket wrench first of all you want to loosen these two nuts with your half-inchMoreAnd a half inch socket wrench first of all you want to loosen these two nuts with your half-inch socket wrench and then this will be the adjusting screw right there.
Why does the chain keep coming off my electric chainsaw?
Chainsaw chains come off the bar due to worn-out bars, worn-out sprockets, and wrongly set tension. You should also note that with continued use, chains lose their tension and hence are more likely to come off the bar when you least expect it.
How do you put a chain on a Poulan electric chainsaw?
So the sharp edge is pointing back on the bottom of the bar. With a pointed the right direction I'llMoreSo the sharp edge is pointing back on the bottom of the bar. With a pointed the right direction I'll go ahead and wrap the cane around this rear sprocket into the groove on the bar.
Why won't my chainsaw chain tighten?
If you can't tighten the chain, you may not be implementing the proper tightening procedure. To adjust the chain, loosen the nuts that hold the guide bar in place. These nuts are located on the side panel. Turn the tension control screw to the right to tighten the chain and to the left to loosen it.
How do you tighten a chain on a chainsaw?
Most chainsaws come with "scwrench" (screwdriver/wrench) that matches their side plate nut and tension adjustment screw size.
Step 1: Loosen the Nuts on the Guide Bar Side Panel. ...
Step 2: Adjust the Tensioning Screw. ...
Step 3: Tighten the Guide Bar Side Panel Nuts. ...
16 Comments.
Why does my chain keep getting loose?
Your chain might simply be too old or can stretch over time. When this occurs you need to replace it. Consider that your loose chain also may be due to operator error. Exceeding the recommended gear range for the rear derailleur on your bike may lead to a droopy chain when you ride in these gears.
Why does my chain keep coming off?
It might be that the chain is worn, has a stiff or bent link, or has become clogged up with dirt. A visual inspection while turning the cranks should reveal if there's a problem here. The chainring, or a chainring tooth, could be bent. Again, a visual check will tell you what you need to know.Dec 21, 2021
How do you put the chain back on a Poulan Pro chainsaw?
How to Replace the Chain on a Poulan Pro Chainsaw
Let's get started.
REMOVING THE CHAIN 1. Remove the side cover.
Remove the chain.
Install the chain.
Reinstall the side cover.
Tension the chain.
What size chain does a Poulan chainsaw need?
Poulan Pro Chainsaw Chains 16" Chain.
Which way does the chain go on a chainsaw?
The correct direction for a blade to face is with the pointy edge of the blade teeth facing toward the way the blade rotates. Essentially, you want the pointy edges of the blades rotating on top of the chain bar, moving toward the tip of the bar, and away from the body of the machine.
