How do you start a Stihl ms360 chainsaw?
- Step 1 of 15: Before starting your chain saw, the chain brake should be activated by pushing it forward (see picture).
- Step 2 of 15: Always remove the bar cover before starting your chain saw.
- Step 3 of 15: If your chain saw is fitted with a decompression valve, press it now.
Full Answer
How to start a Stihl Chainsaw when the engine is cold?
Starting a chainsaw when the engine is cold requires using the choke. For a warm start, you can skip this step. So for a warm start, you’ll move the master control directly to the run position. Otherwise, the steps on how to start your Stihl chainsaw remain the same for both hot and cold starting. Read the steps for starting below the video.
Is there an instruction manual for the Stihl chain saw?
The instructions on the following pages should be regarded as supplementary to the Instruction Manual supplied with your STIHL chain saw. The pictures are only examples of a chain saw. Different chain saw models may have different controls.
What type of Stihl to use for MS 360 Motor?
91 MS 360 español / EE.UU En la mezcla, use únicamente aceite de STIHL para motor de dos tiempos o aceites para motor de dos tiempos enfriado por aire con la clasificación TC. Nosotros recomendamos el aceite 50:1 de STIHL para motor de dos tiempos porque está especialmente formulado para usarse en motores de STIHL.
How do you activate the chain brake on a Stihl Chainsaw?
Activate the chain brake. On a gas-powered Stihl chainsaw, the chain brake is located just in front of the handlebar. All you have to do to activate it is push it forward. This will keep the chain locked as a safety precaution while you are starting the chainsaw, and until you are ready to use the tool.
How do I start my Stihl chainsaw?
1:534:06Chapter 9: Starting Your STIHL Chainsaw - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd pull until you feel slight resistance. At this point give the Rope a sharp brisk pull and thenMoreAnd pull until you feel slight resistance. At this point give the Rope a sharp brisk pull and then guide the rope back slowly into the starter housing.
What are the 4 steps to starting a chainsaw on the ground?
Here's how to start an electric chainsaw:Connect the power cord or the rechargeable battery to the electric chainsaw.Place the chainsaw on flat, level ground. ... Engage the chain brake.Engage the safety switch and simultaneously pull the trigger switch to start the chainsaw motor.More items...
Why is my Stihl chainsaw not starting?
Dirty or clogged fuel tanks, dirty fuel filters and lines, loose fuel hoses, dirty air filters and a dirty carburetor can all restrict fuel flow. Check, clean and replace all the fuel system parts before moving into the internal engine, as gas problems create a majority of starting problems.
How do you start a petrol Stihl chainsaw?
2:344:30How to Start a Stihl Chain Saw - YouTubeYouTubeStart of suggested clipEnd of suggested clipTurn the chain. Give the saw throttle trigger a quick squeeze to disengage the throttle lock andMoreTurn the chain. Give the saw throttle trigger a quick squeeze to disengage the throttle lock and bring the saw to idle.
What's the proper way to start a chainsaw?
0:301:54Chainsaw Basics: How to Start a Gas Chainsaw - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou want to make sure that your toggle switch is in the on. Position your choke is pulled out andMoreYou want to make sure that your toggle switch is in the on. Position your choke is pulled out and you've pressed the purge valve four to five times to prime the engine.
How do you start a chainsaw that has been sitting?
Just let the saw sit for 30 min and the excess gas will evaporate. Remove the spark plug, dry it, crank over the engine a few times to dry the cylinder. Now refit the plug and try again. Set the switch to “On”, set throttle to fully open, set choke to “Off” and crank over the engine.
What would cause my chainsaw to not start?
A spark plug might be defective and needs to be replaced. If your chainsaw has a defective spark plug, it cannot create an electrical current to ignite the system. Remove the spark plug and inspect if it is dirty, cracked, eroded, or damaged. There may also be a heavy carbon buildup or a burned-up electrode.
Why is it so hard to start my chainsaw?
It's possible the engine is flooded with fuel. To clear excess fuel from the carburetor, place the choke lever in the Off position, hold the throttle trigger fully open and pull the starter rope 5 or 6 times. Try to start the chainsaw.
Do you start a Stihl chainsaw with the brake on?
On a gas-powered Stihl chainsaw, the chain brake is located just in front of the handlebar. All you have to do to activate it is push it forward. This will keep the chain locked as a safety precaution while you are starting the chainsaw, and until you are ready to use the tool. Remove the bar cover.
How do you start a Stihl chainsaw without a primer bulb?
0:303:42Stihl MS250 How To Start it - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd had to figure out the trick to get this thing started without a primer button. So I thought IMoreAnd had to figure out the trick to get this thing started without a primer button. So I thought I would just show you guys how to start this saw that doesn't come with a primer button the easiest.
How do you start a Stihl chainsaw UK?
Push your right toecap into the rear handle to stabilize the chainsaw. Step 8 of 15: Slowly pull the starter rope with your right hand until you feel resistance. Then pull the starter rope hard several times until the engine fires briefly.
How to start a Stihl chainsaw when it's cold?
Starting a chainsaw when the engine is cold requires using the choke. For a warm start, you can skip this step. So for a warm start, you’ll move the master control directly to the run position.
How to engage chain brake on Stihl chainsaw?
Engage the chain brake by pushing the chain guard forward until it clicks into position. If you don’t do this the chain will rotate when you pull the recoil starter cord. Your Stihl chainsaw most likely has a decompression valve. It will be at the top of the engine cover, somewhere behind the front handle.
How to test a spark plug on a chainsaw?
You can test the spark by connecting the ignition coil lead to the spark plug and touching the metal part of the plug to the engine head. With the plug touching the metal surface of the engine, pull on the recoil starter.
Why won't my chainsaw start?
This happens when there is too much gas in the combustion chamber and the spark plug gets wet from the excess fuel. The most common cause for engine flooding is when you push repeatedly on the primer bulb, sending through too much fuel.
What is the primer bulb on a Stihl chainsaw?
To one side of your Stihl chainsaw, you’ll find a small, translucent plastic bubble. This is the primer bulb and is used to remove air from the fuel pipe, so that it can flow to the carburetor.
How to use chainsaw safely?
There are two factors to using a chainsaw safely in order to prevent a serious injury. The first step is to use the correct PTFE (Polytetrafluoroethylene) gear. You should wear a helmet, along with ear and eye protection. Wear suitable long trousers and a forestry jacket. Steel-tipped or another type of safety boot is also important.
What happens if you leave a chainsaw standing?
If your chainsaw has been standing unused for a length of time, the fuel is likely to have gone stale. Old fuel should be drained, and the fuel pipe will need to be cleaned. Debris may also collect in the gas tank. This will mean that you need to flush the tank and clean the fuel pipe, before adding fresh fuel.
Why is my STIHL saw spongy?
A "sponginess" in the feel of the saw, increased vibration or increased "bottoming" during normal operation may indicate damage, breakage or excessive wear. Buffers should always be replaced in sets. If you have any questions as to whether the buffers should be replaced, consult your STIHL servicing dealer.
When transporting a chainsaw, what is the appropriate chain guard?
When transporting your chainsaw, use the appropriate chain guard (scabbard). Other important safety precautions are contained in the body of the Owner's Manual. Note: When using a chainsaw for logging purposes, refer to the Code of Federal Regulations, Parts 1910 and 1928.
Is chainsaw a high speed tool?
Because a chainsaw is a high-speed wood-cutting tool, some special safety precautions must be observed as with any other power saw to reduce the risk of personal injury. Careless or improper use may cause serious or even fatal injury. STIHL's philosophy is to continually improve all of its products.
Can you remove the fuel filler cap on a STIHL?
In order to reduce the risk of burns or other personal injury from escaping gas vapor and fumes, remove the fuel filler cap on the STIHL product carefully so as to allow any pressure build-up in the tank to release slowly. Never remove fuel filler cap while engine is running.
How to stabilize a chain saw?
Push your right toecap into the rear handle to stabilize the chain saw. Step 8 of 15: Slowly pull the starter rope with your right hand until you feel resistance. Then pull the starter rope hard several times until the engine fires briefly.
How to start a chain saw with a decompression valve?
Step 2 of 15: Always remove the bar cover before starting your chain saw. Step 3 of 15: If your chain saw is fitted with a decompression valve, press it now. It assists with firing the engine and starting your chain saw.
How to start a Stihl chainsaw?
To start a Stihl chainsaw, start by pushing the chain brake forward to activate it and removing the cover over the chain and bar. Then, press down the primer valve several times if your chainsaw has one, and set the master control to the cold start setting.
How to start a chainsaw from a sitting position?
Hold the chainsaw securely. Keep your left hand on the chainsaw’s handlebar, and lock your elbow. Use your right hand to start the chainsaw, then follow the same directions for pulling the starter rope and starting your tool as you would when beginning from a sitting position.
How to start a chainsaw on uneven ground?
If you must start your chainsaw on uneven ground, Stihl recommends an alternate technique for safety reasons. First of all, use your foot to clear any debris away from your site, and make a small impression in the ground you can use to support your foot.
Where is the decompression valve on a Stihl chainsaw?
If you have a professional saw, simply press the valve down (it will be located on the top of the chainsaw, near the starter rope).
How to cold start a chainsaw?
Set the master control to the cold start setting. Press and hold the throttle trigger lockout (located on the side of the chainsaw, above the trigger) with your thumb, then move the master control (on the left of the rear of the chainsaw) down as far as it will go.
Where is the chain brake on a Stihl chainsaw?
On a gas-powered Stihl chainsaw, the chain brake is located just in front of the handlebar. All you have to do to activate it is push it forward. This will keep the chain locked as a safety precaution while you are starting the chainsaw, and until you are ready to use the tool.
Where is the hand guard on a chainsaw?
The hand guard will be located just in front of the handlebar. Pull it toward you (and the back of the chainsaw) until it clicks. This is a safety feature designed to protect you as you operate the chainsaw, which will not start until the guard is engaged.
Step-by-step starting
Find out how to start your STIHL chain saw from detailed descriptions with illustrations ...
The right way to fit the chain and bar
Find out how to assemble your chain saw and prepare it correctly for use ...
Proper protective equipment
Good protective clothing provides you with the best possible protection ...
Before starting
We show you which oils and lubricants your chain saw needs and the correct way to refuel your chain saw. …
The correct way to store chain saws
Correct storage ensures trouble-free restarting even after taking an extended break ...
Note
The instructions on the following pages should be regarded as supplementary to the Instruction Manual supplied with your STIHL chain saw. The pictures are only examples of a chain saw. Different chain saw models may have different controls.
How to troubleshoot a Stihl chainsaw?
Here’s a quick Stihl Chainsaw troubleshooting guide you can follow: 1. Check the Gas. If your Stihl chainsaw is hard to start, check the gas in the tank initially. You need to replace the gas with a fresh one if you haven't used the chainsaw for a long time. Always change the gas at the start of a new season. 2.
How long does it take for a Stihl chainsaw to sit?
The excess gas can be removed by allowing the chainsaw to sit for 15 to 20 minutes. It will evaporate the extra fuel in the engine. Here is a stepwise guide to help you start a flooded Stihl chainsaw: 1. Shift the Master Control Switch To the Cold Start Position.
Why does my Stihl chainsaw flood?
Another reason behind the flooded Stihl chainsaw is the primer bulb experiencing frequent pushes. If you pull the starter rope too quickly for too long, it will flood the engine with gas.
What to do if your Stihl chainsaw doesn't spark?
What To Do. If it doesn't spark, you need to replace or clean the plug. 3. Fuel Problems. Your Sthil Chainsaw engine must have stopped working due to lousy fuel. Also, the restricted flow of air in the cylinder can cause the stoppage in your Stihl Chainsaw. This can happen due to dirty carburetor, blocked fuel tanks, ...
Why won't my chainsaw start?
Suppose your chainsaw is not starting due to a clogged carburetor, you can clean it with a carburetor cleaner or replace the entire carburetor. 2. Ignition Spark Problems. If your chainsaw has problems in the ignition area, it could be due to faulty wiring connections, broken ignition module, oxidized spark plugs, and broken wires.
Why is my Sthil not starting?
This sticky fuel blocks the carburetor, which prevents the engine from starting.
How to start a chainsaw correctly?
Start the chainsaw correctly by keeping the choke on. While starting the chainsaw from a cold start position, you need to move the choke immediately to the warm position when the engine starts. Press the throttle trigger quickly, as well.
