How do you start a Husqvarna 51 chainsaw?
- Locate the idle-speed screw and the idle-mixture screws on the side of the chainsaw.
- Turn both the low- and high-speed screws clockwise to the midpoint.
- Adjust the low-idle screw clockwise and counterclockwise respectively, until you find the highest idling speed.
How do you start a Husqvarna chainsaw?
How to Start a Husqvarna Chainsaw. When starting you chainsaw with a warm or previously run engine, pull the choke control out and push it back in again. Press the air purge at least 6 times. Press the decompression valve. Pull the starter handle with your right hand and pull out the starter cord slowly until you feel a resistance.
How to start a Husqvarna 455 rancher chainsaw?
After a few hours with Husqvarna 455 Rancher, you will be able to start the unit without even thinking about it. Starting the Husqvarna will be like second nature. The 10 steps to starting a Husqvarna 455 Rancher chainsaw are as follows: Push the chainsaw brake forward into the locked position.
How do you use a Husqvarna Smart Start?
You apply the Husqvarna smart start by pushing it in control; The next step is to push the fuel pump so that you can see the level of the fuel in the tank; Then you pull the starter rope with your right hand while holding the instrument in the left one.
Are Husqvarna chainsaws good for beginners?
Husqvarna chainsaws happen to be one of the most widely used chainsaw models. Although they are popular for their durability and high efficiency, every chainsaw user, especially a beginner, can once in a while face some problems applying their instrument.
How do I get my Husqvarna chainsaw to start?
2:083:52How to Start a Husqvarna Chainsaw - YouTubeYouTubeStart of suggested clipEnd of suggested clipControl press the air purge repeatedly Atlee six times until fuel begins to fill the bulb. The bulbMoreControl press the air purge repeatedly Atlee six times until fuel begins to fill the bulb. The bulb does not need to be completely filled.
What are the 4 steps to starting a chainsaw on the ground?
How to Start the Chainsaw (Step-by-Step)Step 1: Stabilize the Chainsaw. ... Step 2: Engage the Chain Brake. ... Step 3: Turn the Chainsaw On and Open Up the Choke. ... Step 4: Prime the Fuel. ... Step 5: Pull the Starting Cord a Few Times. ... Step 6: Close the Choke. ... Step 7: Let the Chainsaw Idle. ... Step 8: Close the Choke.More items...•
Why will my Husqvarna chainsaw not start?
The carburetor might be clogged. A clogged carburetor is often caused by leaving fuel in the chainsaw for a long period of time. Over time, some of the ingredients in the fuel will evaporate, leaving behind a thicker, stickier substance. This sticky fuel can clog up the carburetor and prevent the engine from starting.
What is the button on top of a Husqvarna chainsaw?
A decompression valve releases some of the compression from the combustion chamber during the starting procedure, making the engine easier to turn over when pulling the recoil rope.
What's the proper way to start a chainsaw?
Place the chainsaw on flat, level ground. Make sure the bar is clear of obstacles and bystanders are at a safe distance. Engage the chain brake. Engage the safety switch and simultaneously pull the trigger switch to start the chainsaw motor.
Why is it so hard to start my chainsaw?
A fuel issue is one of the most common reasons why a chainsaw won't start. If the operator has repeatedly been trying to start the chainsaw through the recoil starter system, they may have accidentally flooded the engine with fuel. A common indication the engine has been flooded is the smell of gasoline in the air.
How do you start a chainsaw that won't start?
0:522:20Top Reasons Chainsaw Won't Start — Chainsaw TroubleshootingYouTubeStart of suggested clipEnd of suggested clipFree you can try cleaning the carburetor with carburetor cleaner to eliminate the clog. If cleaningMoreFree you can try cleaning the carburetor with carburetor cleaner to eliminate the clog. If cleaning is not effective you can often purchase a carburetor repair kit to replace some of the components.
How do you adjust the carburetor on a Husqvarna 51 chainsaw?
How to Adjust a Husqvarna 51 CarburetorLocate the idle-speed screw and the idle-mixture screws on the side of the chainsaw. ... Turn both the low- and high-speed screws clockwise to the midpoint. ... Adjust the low-idle screw clockwise and counterclockwise respectively, until you find the highest idling speed.More items...
Do you start a chainsaw with the brake on?
The chain brake should be activated when you start the chainsaw. Many chainsaw models can be started in what is known as 'half-throttle' position. In this position, the chain can rotate – if the chain brake is not activated.
How do you engage a Husqvarna chainsaw?
Hold the front handle firmly with your left hand. Pull the starter handle with your right hand. Repeat until the engine fires. Push the choke (half-throttle) and pull until the saw starts.
How do you start a Husqvarna 550xp?
2:438:08Starting Procedure for Husqvarna 550 xp Mark 2 + Tree Felling - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo when you put it up into the choke position just pull it one time and when you hear the engineMoreSo when you put it up into the choke position just pull it one time and when you hear the engine engage pop that into the run position and pull away.
How do you start a Husqvarna 61?
2:146:02How to cold start Husqvarna chainsaws. - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe chain one won't spin so that's one thing so put on the on/off switch pull out the choke. Put inMoreThe chain one won't spin so that's one thing so put on the on/off switch pull out the choke. Put in here can brake on pull it your the ignition fire push it.
How to start a chainsaw when it's too cold?
Then you pull the starter rope with your right hand while holding the instrument in the left one. You should use your right foot to help you hold the chainsaw. You should pull the starter carefully and yet powerfully enough. In that moment you also push the throttle halfway and pull the rope until the chainsaw starts running. If the chainsaw is too cold, you just need to warm it up by letting the engine run for some time before performing cutting tasks.
What happens when you start a chainsaw?
When you start your chainsaw, one of the steps will be to press the fuel pump to start your tool easily. If you overdo it, it can lead to the flood of the engine, which will stop its working.
What to do if your chainsaw fuel isn't good enough?
If you notice that your fuel isn’t good enough, you should empty the fuel tank and refill it with higher quality gas. You should make sure that your fuel is suitable for your chainsaw engine. You should be careful and take into account that combinations with ethane or methane are dangerous for the engine and can cause corrosion.
How to fix a chainsaw that won't open after opening spark plug?
In order to solve this issue after opening the spark plug the chainsaw owner should drain the fuel from the chainsaw fuel tank. Then the owner deactivates the choke and then pulls the starter rope at the same time pushing the throttle . Then it’s needed to dry the spark plug and return it to its place.
What happens if your chainsaw air filter is unclean?
If your chainsaw air filter is unclean, it draws less air than gas, which reminds of the time when the choke is on. Moreover, there is more unburned fuel left, while the production of carbon deposits rises. Even more carbon is accumulated with the idle engine.
What happens if your chainsaw is cold?
Cold temperatures – if your chainsaw was lying for some time on a cold floor and in some not so warm places . In this situation the engine gets too cold and there can be a delay in its start until it gets warm enough. To help this you should find the choke and push the choke out;
Why does my chainsaw stop when it's too hot?
Excess air-fuel level – when the chainsaw is too warm, it’s also hard to start. The chainsaw stops when the engine is too heated up because of a high air-fuel ratio.
Tips to Follow to Start a Husqvarna Chainsaw
Turn on the chain brake. If the saw has an Air Purge/fuel pump, push the bulb (prime) many times until the fuel is visible and enters the carburetor. Activate the choke and (on certain models) decompression control. Pull the starting lever until the engine begins to ignite. Pull till the saw begins and then push the choke (half-throttle).
FAQS
During the starting phase, a decompression valve relieves part of the compression in the combustion chamber, making the engine simpler to turn over while drawing the recoil rope.
Conclusion
I hope you’ve figured out that a Husqvarna chainsaw that won’t start isn’t garbage. At least not until you’ve followed the troubleshooting steps to resolve the main issue of how to start a Husqvarna chainsaw. The easy fixes will get your Husqvarna chainsaw up and running again.
How to start a chainsaw without a choke?
If the engine is difficult to start, apply half-throttle. You access the half-throttle function by first fully activating the choke. Then move the control back.
How to get a chainsaw to go down?
The distance between the stump and the guide bar is dependent on the chainsaw model and guide bar length. 2. Release the front handle and allow gravity to bring the chainsaw down, rotating around the rear handle, towards the stump.
How to check chain brakes on a chainsaw?
Chain brake inspection. 1. Start the saw. Hold the chainsaw firmly by the front and rear handles. 2. Accelerate and then release the throttle. 3. Activate the chain brake by turning your left wrist towards the guard. Do not let go of the front handle.
When should the chain brake be activated?
The chain brake should be activated when you start the chainsaw. Many chainsaw models can be started in what is known as ‘half-throttle’ position. In this position, the chain can rotate – if the chain brake is not activated.
How to prime a carburetor on a saw?
If the saw is equipped with Air Purge/fuel pump , press the bulb (prime) a few times until the fuel becomes visible and enters the carburettor.
Where to place rear handle on a scuba diver?
Place the rear handle between your left thigh and behind your right knee.
Do you have to read the operator's manual before starting a chainsaw?
Before starting your chainsaw, be sure to read the operator’s manual for your particular saw since controls may vary between different models. Also, make sure you always observe regulations in your area. The chain brake should be activated when you start the chainsaw.
How to set chainsaw to start?
Push in the compression release on top of the saw. This will make pulling the rope much easier due to the compression being released from the engine. This will automatically push back out once the saw is started. Pull the choke lever to the full choke position. This will automatically set the chainsaw to the start position.
How to start Husqvarna 455 Rancher?
The 10 steps to starting a Husqvarna 455 Rancher chainsaw are as follows: Push the chainsaw brake forward into the locked position. This is a vital step and could save you from severely injuring yourself during the starting process. Place the saw on the ground.
When cutting a car, do you disengage the chain brake?
Disengage the chain brake before accelerating the engine. You are now ready to cut.
How many times do you press the fuel primer bulb?
Press the fuel primer bulb 4 to 7 times to pull gas into the bulb. Please note that the bulb does not have to be completely full.
