Furthermore, how do you start a Homelite 3514c chainsaw? How to Start a Homelite Chainsaw. Open the oil reservoir cap on top of the chainsaw. Fill the oil reservoir with chain saw lubricant. Plug the male end of the extension cord into a power outlet. Locate the two handles on the saw, the top and rear one.
Why won’t my Homelite chainsaw start?
If your Homelite two-cycle chain saw engine won’t start, the problem most likely will be found in the fuel or ignition systems. The most common problem associated with nonstarting two-cycle chain saw engines is old, stale fuel.
How long does gasoline last in a Homelite chainsaw?
The gasolines available in 2014 are complex blends that can go stale in as few as 60 to 90 days. If you run stale fuel in your Homelite two-cycle chainsaw, you risk engine flooding from a gummed-up fuel system that can’t correctly measure out the fuel.
How do you start a chainsaw without a starter?
Place the chainsaw on the ground and put your right foot through the rear handle. Turn the chainsaw on/off switch the on position. Grip the top handlebar with your left hand. Engage the chain brake with your left wrist. Pull the starting cord several times with your right hand until the engine turns over and idles.
How do you turn on a Homelite electric chainsaw?
2:016:20Homelite 16 Inch Electric Chainsaw Review-12 Amp - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo you push that in with your thumb. And then you can push the trigger with your other fingers toMoreSo you push that in with your thumb. And then you can push the trigger with your other fingers to use the chainsaw. Now. I will be demonstrating it momentarily.
How do you turn on a chainsaw?
0:421:54Chainsaw Basics: How to Start a Gas Chainsaw - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou want to make sure that your toggle switch is in the on. Position your choke is pulled out andMoreYou want to make sure that your toggle switch is in the on. Position your choke is pulled out and you've pressed the purge valve four to five times to prime the engine.
How many cc is a Homelite 3514c?
42 ccPowered by a reliable 42 cc 2-Cycle engine, this saw includes pro-features to make your job easier.
How do you start a cold chainsaw?
0:071:31How to Perform a Cold Start on a Chainsaw | Husqvarna - YouTubeYouTubeStart of suggested clipEnd of suggested clipStart move the front hand guard forward to engage the chain. Break pull the choke out. CompletelyMoreStart move the front hand guard forward to engage the chain. Break pull the choke out. Completely then push the air purge six times using your left. Hand hold the body of the chainsaw on the ground.
How do you start a 2 stroke chainsaw?
Pull the Start Cord Hold the saw's upper handle with one hand. Use the other hand to pull up on the start cord. Aim for a quick, smooth stroke. Push the choke back in halfway when the engine starts to turn over.
Why is my chainsaw not starting?
0:062:20Top Reasons Chainsaw Won't Start — Chainsaw TroubleshootingYouTubeStart of suggested clipEnd of suggested clipWhich can prevent the chainsaw from starting you should inspect the spark plug for damage or wear.MoreWhich can prevent the chainsaw from starting you should inspect the spark plug for damage or wear. You can also use an ignition tester to help determine if the spark plug is defective.
What is the fuel mixture for a Homelite chainsaw?
The recommended 50-to-1 fuel mixture includes 2.6 ounces of a high-quality, two-cycle oil with added fuel stabilizers and 1 gallon of unleaded 87-octane gas. Homelite recommends using their brand of oils, specifically designed to work in any model with a 50-to-1 fuel ratio.
What kind of oil does a Homelite chainsaw take?
The ideal oil for a Super 2 chain is Homelite Bar and Chain Oil. Clean SAE 30 oil can also be used to lubricate the chain, according to Homelite. If the temperature is below 40 degrees Fahrenheit, you can dilute the SAE 30 oil with kerosene.
When did Homelite go out of business?
Deere & Company announced on Nov. 16, 2001 that it has sold its Homelite consumer products business.
How to start a chainsaw?
Preparation (Before You Start the Chainsaw) How to Start the Chainsaw (Step-by-Step) Step 1: Stabilize the Chainsaw. Step 2: Engage the Chain Brake. Step 3: Turn the Chainsaw On and Open Up the Choke. Step 4: Prime the Fuel. Step 5: Pull the Starting Cord a Few Times. Step 6: Close the Choke.
How to start a chainsaw that has been warmed up?
If you’re taking a short break from using the chainsaw, then you can restart it without using the choke since the engine is already primed with fuel . Place the chainsaw on the ground and put your right foot through the rear handle.
How to cut a chainsaw with a chainsaw?
Engage the chain brake with your left wrist. Pull the starting cord several times with your right hand until the engine turns over and idles. Raise your body up while holding the chainsaw firmly in both hands until it’s around waist level, then proceed to pull the throttle to cut.
How to start a chainsaw on a high surface?
The chainsaw should always be started on level ground; never up in the air or on a high surface. Place your right foot inside the rear handle and press it down firmly to secure the chainsaw. Place your left hand on the top handlebar. Make sure that nothing is touching or near the chainsaw guide bar or chain.
How to stop a chain from spinning?
With your left hand on the top handlebar, lean your wrist forward to push the chain brake handle forward. This will engage the chain brake, which prevents the chain from spinning during the starting process.
Why won't my Homelite chainsaw start?
Reasons for a Homelite Chainsaw Not Starting. Two-cycle engines, the kind requiring the owner to mix the gasoline with oil, are used on chainsaws and other yard equipment because they provide high power at a low weight. But they are notorious for hard starting. If your Homelite two-cycle chain saw engine won’t start, ...
What happens if you run stale fuel in a chainsaw?
If you run stale fuel in your Homelite two-cycle chainsaw, you risk engine flooding from a gummed-up fuel system that can’t correctly measure out the fuel. Check for flooding by removing the spark plug and examining its tip. If the plug’s tip is wet with fuel, you have a flooding problem.
