How do you screw in cast iron?
- Find the size of the fastener you need to thread into the cast iron on a drill and tap chart.
- Secure the drill bit from the set into the chuck of a variable-speed drill motor.
- Drill the hole into the cast iron by pumping the trigger of the drill motor to keep the rpms of the drill motor low.
How do you cut cast iron bolts?
As he points out, steel cuts well with a torch, cast iron doesn't cut well. Actualy one must be very carefull using this method, it is possible to damage the threads slightly, but generaly works very well. After blowing out most of the bolt, allow to cool thoroughly, remove slag with a drift punch, then chase with a tap.
How do you tap a hole in cast iron?
Tapping a hole drilled in cast iron requires care to avoid breaking taps in the hole when you encounter a hard spot. Find the size of the fastener you need to thread into the cast iron on a drill and tap chart. Follow the line on the chart representing the fastener size to determine the drill-bit size.
How do you drill cast iron without damaging it?
Start with a slow speed setting. More speed = more friction, which means more heat. Slower drilling allows you to go through cast iron without dulling out your bits or over-heating your drill. You should never exceed 3000 RPM, though less than 1000 RPM is doable.
How to cut threaded holes in cast iron machine tables?
Threaded holes in cast iron machine tables are just the solution you need for holding jigs and fixtures. George Vondriska shows how to cut a threaded through or blind hole in cast iron with a center punch, drill, tap and die set, a little oil drill and an all important back and forth motion. You Might Also Enjoy...
Can you screw into cast iron?
Cast iron is brittle, but as far as metals go, it isn't very hard -- so drilling a hole into it isn't as difficult as you might expect. Moreover, you don't have to be overly choosy about your drill bit. Any bit intended for drilling through metal will drill through cast iron.
What is the best way to drill cast iron?
0:393:35How to drill cast iron - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo what I'm going to do is I'm gonna drill a hole in the bottom of my pan. I know that's not logicalMoreSo what I'm going to do is I'm gonna drill a hole in the bottom of my pan. I know that's not logical to most of the world. But I don't do nothing logical. So what we're gonna do is we're gonna mark it
Can you drill and thread cast iron?
Threaded holes in cast iron machine tables are just the solution you need for holding jigs and fixtures. George Vondriska shows how to cut a threaded through or blind hole in cast iron with a center punch, drill, tap and die set, a little oil drill and an all important back and forth motion.
How do you drill a hole in a cast iron pipe?
1:153:43how to cut a hole in a cast iron soil pipe - YouTubeYouTubeStart of suggested clipEnd of suggested clipIdeally would use a mains powered drill for doing this but I like they're just going to use thisMoreIdeally would use a mains powered drill for doing this but I like they're just going to use this cordless drill. And I'm really going to turn the time with it and do it really slowly.
How do you make a hole in an iron?
0:541:58How to drill a hole in metal steel iron - DIY - YouTubeYouTubeStart of suggested clipEnd of suggested clipHere make sure you get it started straight and you want to apply you know a reasonable amount ofMoreHere make sure you get it started straight and you want to apply you know a reasonable amount of pressure there. And um and most for most hand drills you want to run it on high speed.
What kind of Tap do you use for cast iron?
Cobalt steel is harder and tougher than high-speed steel, so it helps increase tool life and it can be used to tap tougher metals such as cast iron, nickel alloys, austenitic stainless, and aircraft alloys. The round shank with square end makes this tap suitable for hand or power-driven applications.
Can you use a self tapping screw in cast iron?
Self-tapping screws are good for use with metals, various types of plastics (plywood, fiberglass, polycarbonates), and cast or forged material, like iron, aluminum, brass or bronze.
Can I weld cast iron?
It is possible to weld cast iron, but it needs to be done using the correct techniques and with care to avoid cracking. Most welding methods require the surface of the material to be cleaned and cast iron benefits from pre and post-weld heating as well as careful cooling.
What is cobalt drill bit?
What are cobalt drill bits? Cobalt bits are a combination of steel (or another alloy) mixed with a small percentage of cobalt, typically between 5 – 7%. Cobalt has a melting point of 1495°C and a boiling point of 2927°C, which makes it perfect for use at high temperatures.
Can you drill a hole in cast iron sink?
Cast iron sink is more brittle compared to stainless steel, so you can easily drill a cast iron sink with the right drill bit. But you must drill slowly to avoid overheating or excessive friction while drilling a hole in the enamel cast iron sink.
Can you drill wrought iron?
Because it is so hard, wrought iron presents a problem for workers attempting to drill at precise positions. Beginning to drill without assistance from clamps can make it difficult to produce a hole that is both straight and on-center. Removing wrought iron fixtures to clamp them to a drill press is the best option.
Is cast iron magnetic?
Most metals with magnetic properties are ferrous: metals and alloys that contain iron. These ferrous metals include mild steel, carbon steel, stainless steel, cast iron, and wrought iron.
Membership Options
Sign up for premium membership and get access to our best woodworking videos and projects. Learn new woodworking techniques and tips from friendly master woodworkers. Anytime. Anywhere.
Bridge Over Broken Guitar
Is the bridge of your guitar separating from the guitar top? You can save big bucks by making the repair yourself. You probably already have all the woodworking tools you need in your shop to fix the broken guitar, and if you follow master woodworker George Vondriska’s step-by-step directions in this video, you’ll gain all…
Cutting Plugs and Using Plug Cutters
Make nearly invisible covers for screw heads with plugs cut from the same wood as your woodworking project. George Vondriska guides you through the procedure for cutting plugs using a drill press, plug cutter bit, bandsaw and George’s secret weapon: masking tape.
Applying Veneer
Applying veneer on your woodworking projects is easy when you know the necessary steps. Our master woodworker George Vondriska teaches you all of the details essential for completing the process, like choosing and applying the right glue and finding the best way to properly clamp the assembly.
Do I Really Need an Impact Driver?
Seeing is believing! Watch this demonstration and don’t be surprised if your next tool purchase is an impact driver. For more information about impact drivers check out the related impact driver product review.
Which is better for drilling through cast iron: lubricating or not lubricating?
Many professional enthusiasts recommend drilling through cast iron without lubricating it. Usually, cast iron contains high carbon content, which acts as a lubricant. So it doesn’t require applying lubricant separately. Despite this, the lubricant makes a mess and helps the debris stick to the drill bit rather than falling away.
Some effective tips to remember while drilling through cast iron
Use extra cutting fluid: Using drill bits extensively can warm up the bit. So if you need to handle a large project, feel free to wipe away the debris often and apply a few oil drops.
FAQs on How to drill through cast iron
A cobalt drill bit with a 135-degree point angle is the best drill for applying to cast iron. Its angle is sharper than a typical drill bit, resulting in faster and more convenient drilling. Even gold-coloured titanium nitride bits are also preferable for drilling through cast iron.
What Do You Need For Drilling Cast Iron?
First and foremost you will need a drill. If you don’t own one go and check my article on top cordless drills.
How to Drill Through Cast Iron
Before you begin drilling, you’ll need to prep all of your tools to cut through the material easily.
Additional Tips and Advice
Safety is essential, but so is convenience. Fortunately, you can get the best of both worlds by following these suggestions. Give them a try and figure out what gives you the results that you’re searching for.
dwayne
I always use plusgas as a penetrating fluid it works the majority of the time but exhaust and head bolts and the like are prone to snapping if that happens now , if possible I weld a new nut on the broken bolt , high temp of weld usually does the trick .
Fosterob
I you have access to it welding something on to the remaining bolt can work well. Usually a nut plug welded over the piece. If no access then drill and re tap may be your only option in which case be very carefull to keep the drill centered on the bolt. If your careful the threads will peel out that way.
Jeff Seelye
If this is the bolt that comes off the manifold, I have tried many methods. Sometimes the penetrant works, sometimes the "weld a nut on" works. Two times I have ground the bolt flush with the manifold (both sides)took a small tip in my cutting torch, heated the bolt shaft and blown the inside out.
John B
Hi Glenn, As the nut is still attached to the bolt, is the piece definitely screwed in with the nut acting as a lock nut? If it is, the parts should be seperable which may make it easier to work with, it seems unusual to have a bolt screwed into a flange which then requires a nut to secure the fitting to it First I would consider welding the existing nut to the bolt, and this should give enough heat to unfreeze the bolt, failing this, apply some heat to the flange rather than the bolt, with a torch, and put on some penetrating fluid (whilst still hot)then try to undo using a good close fitting socket or ring spanner If this fails, then I would consider resorting to drilling out the offending piece. Does the piece have to be rethreaded? or would a bolt and lock nut suffice in this situation? In which case just redrill to the bolt size. Whatever your choice or method, please keep us informed and good luck with it.
Bob S
not sure if I totally understand but if you have access try center punching the broken stud and drilling it out using small drills to start and working up to tap drill size for that stud. then try re-tapping the rest out. at any rate do the least destructive method first and work your way up to thermonuclear devices. bob
covforge
Glen, If it has a nut it usually won't have threads. You might try heating the corner of the manifold to red and try to turn the nut. If it's rusted in this will usually free them up Hope this helps
Charles R. Stevens
Ok, first things first, break out your camera. Torching out a broken bolt or stud, don't use this trick on a blind hole. ATF and naptha is just about as good as it gets for penitraints. Are you dealing with a exaust stud? Comen on the dounstream side of a exaust manifold.
