Measure a stair tread using a tape measure. Subtract 1/8 inch from each tread's measurement and transfer the total to a piece of stair retread material. Place a pencil mark at the appropriate spot on the retread material and draw a line across the retread at the measurement mark, using a framing square as a straight edge.
How can I resurface my stair treads?
Supplies needed to refinish the wood treads
- wood filler (I love this one HERE or HERE)
- spatula ( HERE)
- tinted stain (We will get to what I used in a bit but if you want to use something different than me then you could use this one HERE)
- Spar urethane or any other clear protective coat of choice (I used this one HERE and I prefer satin finishes)
- brush made for oil-based paints and stains ( HERE)
How do you figure out stair treads?
Part 2 Part 2 of 2: Determining the Run, Width, and Length
- Plan for the individual "run" of each step to be 9–10 inches (23–25 cm). The run, or tread, refers to how long each step is.
- Find the total run by multiplying the individual run by the number of steps. The total run refers to how long your overall staircase will be.
- Plan for the width of each stair to be 36 inches (91 cm). ...
How to refinish worn out stair treads?
Steps to Refinishing Your Stair Treads:
- Sand. Start by sanding down the treads to bare wood with the 80 grit sandpaper. ...
- Clean. Vacuum between passes, then wipe down the treads with a tack cloth. ...
- Sand again. ...
- Clean again. ...
- Treat the wood. ...
- Stain the treads. ...
- Apply the Finish. ...
- Sand, then repeat two more times. ...
How to fasten indoor stair treads?
- Secure blocking to the stringers at the front, along the edge located directly behind the risers.
- Install the risers with a level top edge slightly above the top edge of both the blocking and the stringers.
- Never nail into a block from either a tread or a riser.
- Adhere the blocking to the risers and the stringers using a construction adhesive.
Can you put new stair treads over old treads?
Retro-fitting stair treads is the simplest solution for a DIY'er intent on installing hardwood treads over an existing flight of stairs. High-quality prefinished stair treads are made of solid edge-glued wood—not a veneered or engineered material—and can be used to “cap” or reface an existing tread.
What is the cheapest way to redo stairs?
0:1310:20DIY Stairs Makeover for Under $200 with Full Cost Breakdown!! - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo I start off by eliminating the connection between the drywall and stairs by adding a 1-inch pieceMoreSo I start off by eliminating the connection between the drywall and stairs by adding a 1-inch piece of trim to the top of the stringer.
How do you redo stair treads?
Steps to Refinishing Your Stair Treads:Sand. Start by sanding down the treads to bare wood with the 80 grit sandpaper. ... Clean. Vacuum between passes, then wipe down the treads with a tack cloth. ... Sand again. ... Clean again. ... Treat the wood. ... Stain the treads. ... Apply the Finish. ... Sand, then repeat two more times.
How much does it cost to recap stairs?
Hardwood stairs average $100 to $200 per step, including labor. A flight of stairs is 10 to 12 steps and would cost $1,000 to $2,400. Installation and materials can range as low as $1,000 and as high as $30,000.
How do you make old stairs look modern?
Cool DIY Staircase Makeover DesignsChalk Paint Design Pretty Pattern.The Staircase Ombre Effect.Stencil Based Tiles Look.The Staircase Rainbow.Real Tile, No Paint.Traditional Black and White with a Convenient Chalkboard Wall.Use of Decals.Changing the Stair Runner.More items...•
How do you make old stairs look nice?
8:5413:42EASY DIY Staircase Makeover on a Budget - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe rubber backing sticks to the steps and keeps it in place. And then the the rug itself it they'veMoreThe rubber backing sticks to the steps and keeps it in place. And then the the rug itself it they've got really pretty patterns. They're inexpensive this each one cost about $10.
How much does it cost to replace stair treads?
Homeowners pay between $400 and $1,500 for the replacement of stair treads and risers for a standard set of 12. Costs may be higher or lower, based on the materials involved.
How can I refinish my stairs without sanding?
How to Stain Stair Railing Without SandingStep #1 Protect the Area Around the Stair Railing.Step #2 Apply Liquid Deglosser.Step #3 Choosing a Stain.Step #4 Applying a Gel Stain.Step #5 Apply a Stain Sealer.
What flooring is best for stairs?
Ceramic is the most common and recommended tile material for stair risers as it's much more durable than porcelain or glass.
What to do with stairs after removing carpet?
Hardwood Stairs Refinishing ProcessRemove any carpeting from the stairs.Remove all carpet staples.Strip the stain from the treads.Sand the treads and risers using an orbital hand sander.Hand sand the spindles, banister and around the base of the spindles.Vacuum and wipe down everything until the dust is gone entirely.More items...
How much does it cost to change stairs from carpet to wood?
The average cost of replacing your carpeted stairs with wood is said to be around $4,000. Although, the price can range from as low as $1,000 to as high as $30,000. Professionals usually calculate the estimated cost according to the number of steps. The average price of wood installation is $160 for each step.
How much does it cost to put laminate on stairs?
Laminate Planks: Average Cost – $2.00 to $3.50 per square foot, or about $8.00 to $14.00 per stair. Installation Cost: $60-$100 per stair.
What is a retread on stairs?
Retreads give worn stair steps a new nonslip, decorative surface. Retread manufacturers make retreads from many different materials and offer several different stylish designs and colors to match the decor of the room with the stairs. Because retreads mount tightly against the stair's original treads, the retread installer must carefully inspect ...
How do I repair a stair tread?
1. Remove all of the paint and loose material from the stair's treads using a floor scraper. Inspect and repair the stair treads, as needed. Clean the stair's treads using a broom and dustpan.
Do retreads stabilize stairs?
Retreads will not stabilize a structurally unsound staircase. Clean a stair's retreads routinely with soap and water.
What is retrofitting stair treads?
Retro-fitting stair treads is the simplest solution for a DIY’er intent on installing hardwood treads over an existing flight of stairs. High-quality prefinished stair treads are made of solid edge-glued wood—not a veneered or engineered material—and can be used to “cap” or reface an existing tread. The primary advantage of using the prefinished stair treads is the ease of installation.
How long does it take to install prefinished stair treads?
In other words, half the work is done for you, so installation takes only about 15 minutes per tread.
What are the advantages of prefinished stair treads?
The primary advantage of using the prefinished stair treads is the ease of installation. For example, the stairs shown in this article were built of lumber and covered with carpet. Once the carpet was removed, the raw lumber tread was revealed and it was downright ugly.
How deep is stair tread?
Standard tread depth is 11-1/2 inches, and a variety of widths are available to meet your specifications. Additionally, Stair-treads.com is not simply a distributor but also the tread manufacturer, and the company will custom-stain the treads to your flooring.
How do I cut bull nose off of a stair tread?
One way is to cut it off. Using a handheld circular saw or jigsaw, cut the bull nose of the tread back flush with (or slightly behind) the existing riser.
Do you have to remove old lumber treads when refacing stairs?
By refacing the stairs with the new prefinished treads, there was no need remove the old lumber tread. This is a particularly important advantage when dealing with “pre-fab” staircases that are built in a factory and delivered to the jobsite during construction.
Does Armstrong stain dry?
Armstrong’s deck and siding wood stain has nondrying conditioning oils that separate from the drying side of the formula. These oils penetrate deep into the deck or siding wood fiber where the wood’s natural oils used to be. This process rejuvenates the wood. The drying oils stay at the surface, lock in the conditioning oils and create a dry to ]
