If you have 2007 2008 2009 2010 Chevrolet Silverado, you can reset the TPMS by increasing or decreasing the tire pressure without using tools. Follow these instructions to get started: If your vehicle has an ignition button, press the Engine Start/Stop button without touching the brake pedal
- Turn the ignition key to the “ON” position without starting the engine. ...
- Press the Remote Keyless Entry (RKE) transmitter's LOCK and UNLOCK buttons simultaneously for five seconds. ...
- Activate the TPMS sensor.
How do you reset the tire pressure sensor?
- Turn the ignition to on and turn the radio to off.
- Push the TUNE DISPL button on the radio and hold for 5 seconds or until the display shows settings.
- Press the SEEK PSCAN button to scroll through the options until TIRE MON is displayed.
How to fix tire pressure sensor?
The most common ones include the following:
- Faulty Tire Pressure Sensors This is the most common and obvious reason why the TPMS error message shows up on your dashboard. ...
- Tire Pressure Sensor Reset There are times when the tire pressure control module and the sensors lose their connection. ...
- Wheel Replacement
Do tire pressure sensors need to be reset?
They monitor the speed of the rotations of the wheels for any change since underinflated tires are smaller and rotate faster. Though they do not affect tire balance nor corrode, they must be reset with a scanning tool whenever tires are replaced or rotated. Determine the type of TPMS system.
How to tell which tire sensor is bad?
When the TPMS sensor becomes faulty, it may be because of these reasons:
- A Recent Tire Change Did you change your tires the other day? Well, don’t be surprised if your sensor goes bad. ...
- Corrosion Inside The Valve System The TPMS sensor has a valve system that can get rusty. If that happens, your tire sensor won’t detect a flat tire. ...
- Dead Or Low Batteries On The Sensor
How do you reset the tire pressure light on a 2007 Chevy Silverado?
Press the button inside the top of the valve stem on the left (driver's side) front tire with a small flat-head screwdriver to start the release of air from the tire. Release the air for 8 to 10 seconds and remove the flat-head screwdriver to stop the flow of air.
How do you reset the tire pressure monitoring system on a Chevy Silverado?
Turn vehicle to ON/RUN. Push the trip odometer reset stem until Tire Pressure is displayed. Push and hold trip reset stem to begin the sensor matching process. Push trip reset again to confirm.
How do you turn off the service tire monitor light on a Chevy Silverado?
With the engine off, turn the ignition key to the RUN position. This will put the vehicle into reset mode and alert you with two clicks of the horn before the tire pressure monitor service light begins to flash. To reset the truck, turn the headlight switch from ON to OFF four times within three to four seconds.
Where is the TPMS reset button?
In most vehicles the TPMS reset button is found beneath the steering wheel. After changing the tires on your vehicle, the TPMS needs to be electronically reset in order to clear the error code. To do this, hold in the TPMS reset button until the tire pressure light blinks three times, then release the button.
How do you reset the tire pressure sensor on a 2010 Chevy Silverado?
Press and HOLD in the TPMS RESET button (located under the steering wheel) until the TIRE PRESSURE light flashes 3 times then release.Nov 30, 2020
How do you program a Chevy TPMS sensor?
2:114:28How To Reprogram / Re-Learn TPMS On GM Vehicles - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo if you're doing it at home and you don't have a scan tool just take the valve cap off and justMoreSo if you're doing it at home and you don't have a scan tool just take the valve cap off and just deflate the tire till the horn. Blows. This will by letting air out of it will activate the sensor.
How do you reset the tire pressure sensor on a Chevy Captiva?
Turn ignition to the ON/RUN position with the engine OFF (not the ACC position) and lower the driver's side window. Press the trip odometer button until “LEARN TIRE PRESSURES” is displayed. Then hold down the trip odometer button until the horn chirps.
How do you reset the tire pressure sensor on a Chevy Impala?
The Light MethodTurn the ignition to the on position.Pull and push the headlight switch on and off three times. The tire pressure monitoring system is now reset and will recalibrate as you drive.
How do you reset the tire monitor on a 2008 Chevy Silverado?
Manual relearn with Odometer ResetInflate all tires.Apple parking brake.Turn ignition ON.Push and hold the trip odometer reset step on instrument panel until PRESS (✓) TO RELEARN TIRE POSITIONS is displayed.Push (✓) to confirm.Horn sounds 2x and TIRE LEARNING ACTIVE will display.More items...
How do I turn off the TPMS light?
0:273:50Disabling the TPMS Warning Light - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo if you have a light that's on what are your options for disabling it well the electrical tapeMoreSo if you have a light that's on what are your options for disabling it well the electrical tape route is probably the cheapest just cover up the light on your - unfortunately.
How do I clear a TPMS code?
Press the TPMS reset button and hold it until the light blinks three times, then release it. Start the car and let it run for 20 minutes so it can reset the sensor. The tire pressure monitor reset button is located beneath the steering wheel. Check your user's manual if you're having trouble locating it.
Where is TPMS sensor located?
The direct TPMS is used more often in the United States. The sensors are located in the tire pressure valve, which acts as an antenna, or are wrapped around the rim of the wheel with a band clamp. These devices transmit the information to an on-board computer.
How to reset a tire sensor?
Start from the driver side front tire, remove the valve cap, and then increasing or decreasing the tire’s air pressure until a horn chirp sounds. Repeat the process for the passenger side front tire, passenger side rear tire, and the driver side rear tire. A horn chirp will confirm that the sensor has been reset.
What happens if you replace a spare tire with a road tire?
If you replacing a spare tire with a road tire containing the TPMS sensor on your Chevy Silverado 1500, the system will detect a malfunction and the low tire pressure warning light will blink. When that happens, the TPMS sensor reset process must be done. Depending on the vehicle model you have, here are a few ways to reset the TPMS.
Why reset tire pressure sensor on Toyota?
So that is very important to control the tire pressure and be able to adjust it. Low tire pressure increases fuel consumption. Also, because of low pressure the friction road is increased.
How to tell if TPMS receiver is ready?
The horn will sound twice to indicate the TPMS receiver is ready, and the TIRE LEARNING ACTIVE message will display. If your vehicle does not have the DIC buttons, press and hold the trip odometer reset stem until the horn chirps twice and the TIRE LEARNING ACTIVE message is displayed;
What is a TPMs system?
Tire pressure monitoring system, or TPMS, – is a feature of many modern cars. It allows to control tire pressure, sitting at your comfort driver’s seat. When the air goes out of the tire, your pressure sensor gives warning and all you need is just to reset it.
2 Answers
An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.
john h
An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.
