How do you reset a gatehouse deadbolt?
- Remove battery pack.
- Press and HOLD the Program button while reinserting the battery pack.
- Press the Program button once more.
- Perform the door handing process again to teach the lock the orientation of the door.
How do you program a gatehouse deadbolt lock?
Press key 0 on the keypad and then press the GATEHOUSE button to complete the process. As with most Electronic Deadbolts, your Gatehouse Single-Cylinder Electronic Deadbolt has a Programming Code that allows you to make programming changes in the lock—such as adding and deleting User Codes.
Can I reset a gatehouse single cylinder keypad deadbolt?
Note: If you have a Gatehouse Single Cylinder Keypad Deadbolt, this reset method won’t work for you. See how to reset a Gatehouse Single Cylinder Electronic Deadbolt.
What happens if I factory reset my gatehouse lock?
But first, keep in mind that factory resetting your Gatehouse Lock will remove all your previous programming functions. So you’ll have to start all over again to program the lock as you did when you just installed it.
How does the gatehouse single-cylinder electronic deadbolt work?
Your Gatehouse Single-Cylinder Electronic Deadbolt comes with an auto-locking function. This feature automatically locks the lock after a few seconds when the door closes—and is left unlocked. To get this feature to work, you’ll need to enable it.
How do I reset my Gatehouse electronic deadbolt?
Press and hold the SET button (a little circle button on the inside of the interior assembly; see the image above). Keep holding the SET button. Next, put the battery back in and then release the SET button. The green LED indicator will illuminate, followed by two beeps and that shows the lock is reset.
How do I reset my Gatehouse lock?
Gatehouse Programming Code - How to Reset All Pre-Programmed CodesEnter your 6-digit programming code and hit the lock button.Enter "30" and hit the lock button.Enter 1-2-3-4-5-6 and then the lock button to delete this default user code.Wait ten seconds for the light to go off.More items...
How do I change the code on my gatehouse door lock?
Changing the Programming Code on a Gatehouse Single-Cylinder Electronic DeadboltEnter the existing Programming Code (the one you want to change) and press the GATEHOUSE button.Press key 4 on the keypad and then press the GATEHOUSE button.Enter a new Programming Code (4 digits) and press the GATEHOUSE button.
How do you reset a deadbolt keypad?
0:050:41How To Restore the Schlage Keypad Lock to Original Factory SettingsYouTubeStart of suggested clipEnd of suggested clipTo restore the default settings disconnect the battery. Then press and release the slake button onMoreTo restore the default settings disconnect the battery. Then press and release the slake button on the keypad. Reconnect the battery.
How do you reset a door lock code?
0:001:23How to Change Programming Code On Schlage Door Lock - YouTubeYouTubeStart of suggested clipEnd of suggested clipPress 3 enter your new programming. Code this code must be six digit long and the force first digitMorePress 3 enter your new programming. Code this code must be six digit long and the force first digit must be different from any user code finally input your new programming code again to confirm. If.
How do I program my electronic deadbolt?
Step 1: Press and hold the SET button until the red LED lights and the lock beeps twice. Step 2: Input your current programming code and press the Lock button. Step 3: Press 3 and 0 (30) and then press the Lock button. Now enter the user code you want to delete and press the Lock button.
How do you install a gatehouse deadbolt?
0:502:21How to Install a Single-Cylinder Deadbolt Lock - YouTubeYouTubeStart of suggested clipEnd of suggested clipFinally install the cylinder half of the lock on the opposite side of the door secure. EverythingMoreFinally install the cylinder half of the lock on the opposite side of the door secure. Everything with the screws from the lock kit. Apply lipstick to the raised part of the end of the bolt.
How do I change the 4 digit code on my TRU bolt lock?
0:265:05How to program a TruBolt/Honeywell electronic keypad - YouTubeYouTubeStart of suggested clipEnd of suggested clipHit four hit the unlock again. And i'm gonna put in my new code which is one four two five three sixMoreHit four hit the unlock again. And i'm gonna put in my new code which is one four two five three six i'm gonna hit the unlock again and i'm gonna re-enter. It.
How do I reset my Schlage keypad lock without code?
So first how to Reset Schlage Keypad lock?Disconnect the batteries.Press and hold the Outside Schlage Button.While holding the Outside Schlage Button, Reconnect the batteries.Release the Outside Schlage Button.To check that the lock was reset, press the Outside Schlage Button and enter one of the Default User.More items...
How do I change my keypad code?
3:095:11How to change keyless entry deadbolt, key pad code on entry door. Easy!YouTubeStart of suggested clipEnd of suggested clipWe're going to hit the reset button here hold it down for five seconds until we hear three longMoreWe're going to hit the reset button here hold it down for five seconds until we hear three long beeps. Beautiful now we have to set the door handing to get the lock to work.
How do you change the code on a push button lock?
1:224:37399. How to change the code on a mechanical push button ... - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo take three eight. And then go underneath and do the same with four. Take four out. And all youMoreSo take three eight. And then go underneath and do the same with four. Take four out. And all you need to do now is switch them around so you put three back in.
How do you open a locked door with a code?
0:130:33Door lock basics - YouTubeYouTubeStart of suggested clipEnd of suggested clipCode. If you accidently enter a wrong number press the lock button to start over the lock buttonMoreCode. If you accidently enter a wrong number press the lock button to start over the lock button will also turn the home and emergency button back lights on.
Performing the Door Handing Identification
If you’ve just installed your Gatehouse Single-Cylinder Deadbolt (first-time installation), the first thing you want to do is perform the door handing identification. This will teach the lock the orientation of the door—whether it’s a right-handed or left-handed door.
Changing the Programming Code on a Gatehouse Single-Cylinder Electronic Deadbolt
As with most Electronic Deadbolts, your Gatehouse Single-Cylinder Electronic Deadbolt has a Programming Code that allows you to make programming changes in the lock—such as adding and deleting User Codes.
Adding New User Codes
As you probably know, a User Code for this lock is a 4 to 10-digit number that allows you to unlock the lock through the keypad. That is, you can unlock your door by entering a User Code via the lock’s keypad.
Deleting Existing User Codes
You can delete a single existing User Code or delete all User Codes at once. Let’s begin with how to delete a single User Code:
Deleting All Existing User Codes
As mentioned earlier, you can also delete all existing User Codes on your Gatehouse Lock at once. However, note that you can’t lock/unlock the lock via the keypad when all User Codes are deleted—so you have to program new codes after deleting all User Codes.
Performing a Factory Reset
You want to reset your lock if you’ve lost/forgotten the codes or are having some issues with the lock.
Related Questions and Troubleshooting Tips
If this happens after installing the lock or performing a reset, chances are you didn’t perform the door handing identification. Perhaps you did, but not properly done.
