- Locate the spa's high-limit reset. This is a red button found on many spa packs.
- Press the high-limit reset button.
- Turn on your spa and observe its operation.
- Flip the breaker panel switch on or press the reset button on the GFCI outlet to restore power.
Is there a reset button on a Cal spa?
Note that all spas don’t have this feature. Clear any blockages or debris covering the drain or Cal Spa filter, then reset by depressing any button located on the top side panel. Indicates possibility of inadequate water flow to heater to carry heat away from the spa unit’s heating element.
How do I reset the power to my spa?
Flip the breaker panel switch on or press the reset button on the GFCI outlet to restore power. Turn the spa on.
How do I troubleshoot a Cal spa?
Troubleshooting 1 Message on the control panel. A message on the control panel may indicate a problem. ... 2 Problems starting up. Note: The priming procedure described here applies to Cal Spas built in 2013 and earlier. ... 3 Power and electrical problems. ... 4 Heat problems 5 Jet problems 6 Water pressure problems
How do I measure for a Cal spa replacement hot tub cover?
The Cover Guy has all the Cal Spa models on file so you never need to measure for your new hot tub cover! When ordering your Cal Spa replacement hot tub cover just leave the dimensions field blank. Leave us a note in the note section saying what model you have, and The Cover Guy will take care of the rest.
How do I reset my hot tub control panel?
1:112:01How to RESET your HOT TUB - YouTubeYouTubeStart of suggested clipEnd of suggested clipGo over to your breaker panel. And flip your breaker or breakers. Down there are some hot tubs thatMoreGo over to your breaker panel. And flip your breaker or breakers. Down there are some hot tubs that have two breakers. And some hot tubs that have one breaker. But you will go to your sub panel.
Is there a reset on a hot tub?
There are generally two "hard resets" in hot tubs, the GFCI, and the high limit reset. The GFCI pops if there is any type of electrical short (such as water getting into the heating element, the reset on that can be in one of three places.
How do you restart a spa?
How To Restart Your Hot Tub If You Haven't Used It in AwhileTurn Off the Power. Before doing anything, you want to turn off the power to your hot tub. ... Drain Your Hot Tub. ... Flush Your Hot Tub Jets. ... Clean Your Spa and Your Cover. ... Clean Your Spa Filter. ... Let Your Spa Dry. ... Check Your Wiring. ... Refill Your Hot Tub.More items...
Why is my Cal Spa not heating?
The filter may be dirty or may need to be replaced. A dirty or clogged filter will restrict water flow and shut down the heater. Clean or replace the filter to re-establish water flow.
Where is the reset button located on a hot tub?
Locate the spa's high-limit reset. This is a red button found on many spa packs. It may be located on the heater and covered by a rubber nipple.
How do you reset hot tub after power outage?
A GFCI is required in all spa installations. It is a micro-circuit breaker, much more sensitive to voltage fluctuations than a normal circuit breaker. If the GFCI has been tripped by a power surge or brownout, just pressing the “RESET” button, if there is one, will turn the circuit, and your hot tub, back on.
Where is the high limit reset switch on a hot tub?
Occasionally, the high limit switch will trip when you're filling your spa. Or it might need a reset from time to time for no known or serious reason. Simply reset by pressing the big red button on your spa pack. The high limit switch may be housed in a thermowell.
How do you troubleshoot a hot tub?
0:055:265 Common HOT TUB PROBLEMS and Solutions | Swim UniversityYouTubeStart of suggested clipEnd of suggested clipSo number one is that your hot tub won't heat properly. So why is that well it simply could be yourMoreSo number one is that your hot tub won't heat properly. So why is that well it simply could be your heater element. If that's not the problem it could be low flow from your pump.
How do I know if my hot tub control panel is bad?
Control Panel is Not Working If only a part is not working, look for error messages or blinking lights. As a first step, reset your breaker. If the problem persists, turn the breaker off and disconnect the panel to examine the circuit board. Turn the power on and check if the hot tub heats up or starts to filter.
How do I set my Cal spa to standard mode?
0:030:48Cal Spas Setting Heating Mode Adelaide All Spas - YouTubeYouTubeStart of suggested clipEnd of suggested clipThis indicates standard mode and the spa will maintain its set temperature by pressing theMoreThis indicates standard mode and the spa will maintain its set temperature by pressing the temperature button and the light button again a value of EC will be displayed.
How long does it take for a Cal Spa to heat up?
If your hot tub is located inside, and the air temp is around 76 degrees, it will take about 4 hours to heat up your spa to 100 degrees. The lower the outside temps the longer you will have to wait before your spa is ready.
What does SL mean on a Cal Spa?
Sleep –SL: Sleep – Sleep mode will only allow the spa to heat within 20 degrees of the set temperature.
What is a Cal spa?
Cal Spas is one of the oldest manufacturers of hot tubs in North America and with that comes tremendous experience and a quality product. Spa Models: Genesis Spa. Gen II Spa. Patio Spas.
How long does it take for a spa to shut down?
Means there isn’t enough water to start it or a possibility of a dry heater – spa is shut down for 15 minutes. Check to determine conditions such as closed valves, suction flow restrictions, pump prime, low water level, trapped air and too many closed jets. You can depress any button to reset theheater start-up.
How many models of hot tubs does Cal Spas have?
Cal Spas. Cal Spas was founded in 1979, and they currently offer more than 250 product models. Each of their hot tubs can be customized from a list of thousands of options, and the company places an emphasis on innovative touches and quality workmanship.
Where are Cal Spas located?
Cal Spas is based out of California, and they have earned an A+ Better Business Bureau rating. Cal Spas focuses on offering home resort experiences, and they have been honored with numerous industry awards. The company’s products are also TradeCertified, meet the UL Certified standard of excellence and are ETL Listed.
How long does the jets 1 run on a spa?
When you exit the Priming Mode, the Circ Pump runs by itself.Priming Mode goes on for 4 minutes, but can be exited earlier by depressing the Temp button. During Priming Mode, the heater is not permitted to run.
Ruttagger
I've had FL codes in the past but a new Pressure switch has always cleared it up. Here is what is happening now.
RDspaguy
Not the filter. Turn of power for 10 seconds. It will still save your time, settings, etc. But will clear your codes.
Ruttagger
Not the filter. Turn of power for 10 seconds. It will still save your time, settings, etc. But will clear your codes.
RDspaguy
That helps, alright. You have a bad or poorly adjusted pressure switch. New part does not always mean good part. And new for you could have been on various shelves for years before you even touched it. Usually this is a sign of a leak in the diaphragm of the pressure switch shorting out the terminals.
