2008-2014
- Turn the key to ON/RUN position with engine off
- Fully depress and release the accelerator pedal 3 times within 10 seconds
- Turn the key to the OFF position and then back on to confirm reset was accepted
- Turn the key to ON/RUN position with engine off.
- Fully depress and release the accelerator pedal 3 times within 10 seconds.
- Turn the key to the OFF position and then back on to confirm reset was accepted.
How do I reset my Dodge Avenger?
0:001:00How to Reset the Oil Change Required Reminder on a Dodge ...YouTubeStart of suggested clipEnd of suggested clipOnce that's due and the simple way to do this one is to turn the key back off. Turn the key to theMoreOnce that's due and the simple way to do this one is to turn the key back off. Turn the key to the on position. And hit the gas pedal three times to the floor.
Why is my 2008 dodge avenger not starting?
The most common reasons a Dodge Avenger won't start are a dead battery, an alternator problem, or failed starter.
How do you reset the PCM?
Please see the following steps:Press and hold the PCM info button for approximately 10 seconds until the PCM reboots.Immediately select the following from the PCM CAR > OPTION > Set PCM System > Reset PCM > Vehicle Handover > Yes > Yes.
How do you reset the electronic throttle control system on a Dodge Avenger?
Turn ignition switch “ON” and wait at least 2 seconds. Turn ignition switch “OFF” wait at least 10 seconds. Turn ignition switch “ON” and wait at least 2 seconds. Turn ignition switch “OFF” wait at least 10 seconds.
What do you do when your Dodge Avenger won't start?
Dodge Avenger Won't StartPut the key in the ignition of your Dodge Avenger and try to turn it. ... Check to see if the battery has a charge. ... Check the fuel level in your Avenger. ... Turn the key to the start position and listen for any noises that your Avenger makes. ... Open the hood.
How do you jumpstart a Dodge Avenger?
1:201:57How to Change a Dodge Advenger Battery and How to Jump StartYouTubeStart of suggested clipEnd of suggested clipAnd they'll put this bumper and put the positive here and negative on that side and that will jumpMoreAnd they'll put this bumper and put the positive here and negative on that side and that will jump the vehicle. So that leads right to the battery to charge. It off.
How do I reset my ECU manually?
0:141:33How to reset your ECU in less than 1 minute - YouTubeYouTubeStart of suggested clipEnd of suggested clipThen once you've opened the hood you need to find on the fuse box the fuse that says ECU. Which isMoreThen once you've opened the hood you need to find on the fuse box the fuse that says ECU. Which is this one. And now that you found it the only thing you need to do is remove.
How do I reset my ECU without a scanner?
0:121:03Learn 3 Ways to turn OFF Engine light in 1 minute, How to reset ECU ...YouTubeStart of suggested clipEnd of suggested clipElectronic control unit or on some cars ecm electronic control module remove the fuse. And put itMoreElectronic control unit or on some cars ecm electronic control module remove the fuse. And put it back again it will reset the ecu. And turns off check engine.
Will disconnecting battery reset PCM?
A. It depends on the car's age and type of ECU used. On some older cars, disconnecting the battery will reset the system but in most new cars it does nothing, except potentially reset the clock and radio station presets.
How do I reset my throttle position sensor?
The easiest way to reset your throttle position sensor is to unhook the negative cable from your battery for up to five minutes or to remove the fuse for your engine control module.
What does the red lightning bolt mean on a 2008 Dodge Avenger?
The lightning bolt warning light alerts you to a fault in the electronic throttle control system in your vehicle. This may be a faulty throttle body, the throttle body sensor or possibly the throttle body control motor which is what controls the opening and closing of the throttle body as the motor requires more fuel.
How do you reset the red lightning bolt on a Dodge Avenger?
0:582:15red lighting bolt fix ( dodge / jeep / Chrysler ) RELEARN PROCESSYouTubeStart of suggested clipEnd of suggested clipOkay what you have to do is press the gas pedal all the way inside. And then release slowly. ThereMoreOkay what you have to do is press the gas pedal all the way inside. And then release slowly. There and put it on the off position and then turn on the car. And that should fix your problem.
Anonymous
Ok, trust me on this one, take the drivers side tire off and remove the forward inner fender panel. If you try it without removing the tire, it is just a royal pain.
Anonymous
It is in the drivers side fender well in front of the tire, it is mounted to the front frame rail. You have to remove the plastic fender lining to get to it.
Anonymous
it's DOT 4 or DOT 5 check with your manual and sometimes it's even in the fluid fill cap.
