Insert a putty knife between the front cabinet and top of the washing machine, approximately 6 inches from each side to release the spring clips. Lift up the top and locate the lid switch on the underside of the top. Pull the two wires off of the two lid switch terminals.
How do you replace a lid switch on a Kenmore washer?
Use this guide to replace a faulty lid switch on your Kenmore 110 series washing machine. To avoid risk of electric shock, unplug the washing machine. Using a 5/16" socket wrench or an adjustable wrench, remove the three screws from the top rear of the washer. Lifting from the rear, remove the top panel.
How do I remove the top panel of my Kenmore Elite washer?
To avoid risk of electric shock, unplug the washing machine. Using a 5/16" socket wrench or an adjustable wrench, remove the three screws from the top rear of the washer. Lifting from the rear, remove the top panel.
Why won’t my Kenmore washer Series 70 spin?
If your Kenmore Washer Series 70 won’t spin, there could be many reasons why this is happening. Troubleshoot the washing machine by redistributing the laundry load, leveling your machine, and checking the washing machine’s power source. You should also check the hose for any kinks, remove blockages in the drain, and check the drive belt.
How do I reassemble my lid switch?
Carefully unplug the two wires connected to the lid switch. Remove the two Phillips screws securing the bracket. Remove the green ground wire. With a screwdriver, remove the single screw connecting the lid switch to the bracket. Almost done! To reassemble your device, follow these instructions in reverse order.
How do you check the lid switch on a Kenmore washer?
Set your multimeter to the lowest ohms of resistance and test your lid switch. If it does not read any continuity, then your lid switch is indeed faulty. You will need to unmount it and replace it.
How do you replace a lid switch?
0:262:01Replacing the Lid Switch in a Direct-Drive Washer (Kenmore ...YouTubeStart of suggested clipEnd of suggested clipOut remove the screw from the green ground wire and release it remove the lid switch mounting screwsMoreOut remove the screw from the green ground wire and release it remove the lid switch mounting screws release the lid switch wire harness from the clips. And pull the lid switch out of the cabinet.
Can you bypass lid lock on Kenmore washer?
1:072:52Bypass lid switch kenmore washer - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou just bypassed the lid switch all you have to do.MoreYou just bypassed the lid switch all you have to do.
How do you replace a lid switch on a top load washer?
1:193:22Washer Not Spinning? Replace Washer Lid Switch #3949238YouTubeStart of suggested clipEnd of suggested clipYou can use a flathead screwdriver to assist in detaching the harness. Remove the old lid switch byMoreYou can use a flathead screwdriver to assist in detaching the harness. Remove the old lid switch by using pliers to evenly squeeze both sides of the wire connector.
How do I know if my washer lid switch is bad?
Signs The Lid Switch Is Bad If the control panel doesn't detect the switch as being engaged, then the washer won't agitate or spin when you close the lid. Your washer may or may not fill with water when you have a bad lid switch depending on the model you have.
How do I replace the switch on my Kenmore washer?
1:153:47Kenmore Top-Load Washer Lid Switch Assembly WP8054980YouTubeStart of suggested clipEnd of suggested clipUsing a Phillips head screwdriver unthread the lid switch mounting screws lift up the washer lidMoreUsing a Phillips head screwdriver unthread the lid switch mounting screws lift up the washer lid depress. The tab and you can remove the old assembly.
Will washer work without lid lock?
NO. The lid lock it to prevent injury to the people near the washer, as without it stopping the machine, the agitator will turn with the lid open. So. If you will open the top up, you should see the lid switch, and you should see the electric wires attached to it.Apr 11, 2017SOLVED: lid lock bypass procedure - washer - iFixithttps://www.ifixit.com › Answers › View › lid+lock+bypa...https://www.ifixit.com › Answers › View › lid+lock+bypa...Search for: Will washer work without lid lock?
How do you bypass a magnetic lid switch?
0:301:51How to Bypass Magnetic Lid Switch on GE Washer - YouTubeYouTubeStart of suggested clipEnd of suggested clipHere. That's actually that's actually a pretty strong magnet. So you yank it. Off oops you set itMoreHere. That's actually that's actually a pretty strong magnet. So you yank it. Off oops you set it right on top. And then you can watch the washer do its final spin or whatever. While the lid is open.How to Bypass Magnetic Lid Switch on GE Washer - YouTubehttps://www.youtube.com › watchhttps://www.youtube.com › watchSearch for: How do you bypass a magnetic lid switch?
How do you open a washing machine lid without power?
To unlock the lid:Pausing the machine will allow you to open the lid.During the spin cycle, pausing the washer does unlock the lid but for safety reasons you must wait until the basket has completely coasted down to a stop before the lid unlocks.Top Load Washer - Lid Lock Feature - All GE Appliances Productshttps://products.geappliances.com › appliance › gea-supp...https://products.geappliances.com › appliance › gea-supp...Search for: How do you open a washing machine lid without power?
What is a Kenmore Series 70 washer?
A top-loading washer like the Kenmore Series 70 has a switch that depresses when you close the lid. This is a safety precaution that detects when the lid is closed. If the tab on the underside of the lid is damaged, it won’t activate the switch.
Where is the lid switch on a washer?
If it’s not working properly, your washer may not work at all. You can find the switch in the door frame of the washer.
Why won't my Kenmore washer spin?
If your Kenmore Washer Series 70 won’t spin, there could be many reasons why this is happening. Troubleshoot the washing machine by redistributing the laundry load, leveling your machine, and checking the washing machine’s power source. You should also check the hose for any kinks, remove blockages in the drain, and check the drive belt.
How high should a washing machine drain hose be?
If the drain hose is too high, the water will flow back into the washing machine. Do not install a drain hose that is higher than 96 inches from the floor. If the hose is the proper length, check for kinks and straighten it.
What to do if Kenmore washer won't drain?
What to Do If Your Kenmore Washer Series 70 Won’t Drain. If your Kenmore Washer Series 70 isn’t draining, first verify that you fully close the lid. Otherwise, the washer won’t enter the spin cycle. Also, check that you have selected the correct cycle for the load.
How to tell if your washing machine is unlevel?
Other signs of an unlevel washing machine are excess noise and vibration during the washing process. If this is the case, adjust each leg higher or lower until you completely level the washer.
What is the pump in a washing machine?
The washing machine pump is responsible for removing water from the tub after the spin cycle. If you think debris is clogging the pump, locate the pump in the washing machine’s main access panel. Check the pump to see if anything is blocking it, like socks or other small clothing.
What happens when you bypass the lid switch on a Kenmore washer?
Warning. When bypassing the lid switch, touch only the insulated portion of the jumper wire with your fingers. The lid switch on your Kenmore washer completes the electrical circuit when the lid is closed. When your washer will not operate, you need to troubleshoot the lid switch before investigating other possible causes.
How to test a lid switch?
The best way to test the lid switch is with a volt-ohm meter. If you do not have a volt-ohm meter, you can bypass the lid switch using a jumper wire to simulate the connection to the washer wiring harness. Advertisement.
Where is the lid switch wire harness?
Locate the lid switch wiring harness on the rear of the top panel. Grasp the wiring harness connector with your fingers and pull it away from the lid switch plug.
Introduction
Use this guide to replace a faulty lid switch on your Kenmore 110 series washing machine.
Step 2
Using a 5/16" socket wrench or hand wrench, remove the two screws from the component cover.