This article provides step-by-step instructions for replacing the fuel return line on a Poulan chainsaw. Let's get started. REMOVING THE FUEL RETURN LINE 1. Drain the fuel. Drain any excess fuel from the tank. 2. Remove the top cover. Remove the (3) screws securing the top cover to the saw. Lift the top cover away from the saw.
How to put new gas lines on a Poulan chainsaw?
Things You'll Need
- Screwdriver
- Allen wrench
- New primer bulb
How to rebuild Poulan chainsaw?
- Remove the air filter.
- Pour about a teaspoon of fuel into the carburetor.
- Pull the starter rope.
How to replace gas tubing on a Poulan Chain Saw?
When it's time to replace the chainsaw fuel lines, it's important that you cut the new tubes to the proper length. Use needle-nose pliers to remove the tubes from the carburetor and pull them from...
How to fix a Poulan chainsaw?
There could be several reasons for this:
- The spark plug is failing, so there won’t be sufficient spark, especially as the engine is warmed up.
- Vapour lock.
- Blocked air filter, causing insufficient air in the combustion chamber.
- The Ignition module is packing up.
- There may be insufficient fuel.
How do you replace fuel lines on a Poulan chainsaw?
2:567:53Chainsaw Repair - Replacing the Fuel Return Line (Poulan ... - YouTubeYouTubeStart of suggested clipEnd of suggested clipFirst. Now remove the fuel cap. And with my hemostats pull that fitting in the fuel line out of theMoreFirst. Now remove the fuel cap. And with my hemostats pull that fitting in the fuel line out of the tank. I'm going to cut the fuel line away from the fitting that was inside the tank. So I can reuse.
Where do the fuel lines go on a Poulan chainsaw?
4:1610:01Where do the fuel and primer lines go in a Craftsman or Poulan Chainsaw?YouTubeStart of suggested clipEnd of suggested clipSo that just goes into the tank there and it stays up top on the top of the tank.MoreSo that just goes into the tank there and it stays up top on the top of the tank.
How do you install a fuel line on a chainsaw?
4:466:09Install Chainsaw Fuel Line In 20 Seconds: Make The Homemade ToolYouTubeStart of suggested clipEnd of suggested clipI'll quickly show you how it works one more. Time. Okay so we'll show you how it works you're goingMoreI'll quickly show you how it works one more. Time. Okay so we'll show you how it works you're going to take the tool you're going to push it right through the hole.
How do you replace the fuel line on a Poulan Pro pp4218avx?
4:1113:03Poulan chainsaw fuel line replacement - YouTubeYouTubeStart of suggested clipEnd of suggested clipOn the top of the gas tank. Now what i usually do is take pb blaster wd-40 or some kind of oil toMoreOn the top of the gas tank. Now what i usually do is take pb blaster wd-40 or some kind of oil to lubricate the fuel line that way it'll slide down into the top of the fuel tank.
Which fuel line goes where?
The (clear) fuel intake line runs from the top of the carburetor (straight nipple) and goes to the short post on the back of the primer bulb. The return line (blue) comes from the long post on the back of the primer bulb and goes into the bottom of the fuel tank.
Where does the fuel line go on a carburetor?
2:0615:37CORRECT FUEL LINE ROUTING AND BENCH TESTING 2 & 4 ...YouTubeStart of suggested clipEnd of suggested clipWith your fuel filter on the end. From the suction side of the carburetor you'll have a fuel line toMoreWith your fuel filter on the end. From the suction side of the carburetor you'll have a fuel line to the suction side of your purge bolt whenever you go to press the purge bulb.
What size is Poulan chainsaw fuel line?
Poulan Pro Fuel Line Kit No. Comes with a large 3/16" OD by 3/32" ID 2 feet long, small 9/64" OD by 5/64" ID 2 feet long. Also comes with the fuel line fitting connector.
How do you change the fuel lines on a Poulan p3314?
2:417:30Poulan Chainsaw Repair - How to Replace the Fuel Return LineYouTubeStart of suggested clipEnd of suggested clipFirst. Now remove the fuel cap. And with my hemostats pull that fitting in the fuel line out of theMoreFirst. Now remove the fuel cap. And with my hemostats pull that fitting in the fuel line out of the tank. I'm gonna cut the fuel line away from the fitting that was inside the tank. So I can reuse.
How do I put fuel lines in my tank?
2:354:35How to Replace the Fuel Line in a Line Trimmer - YouTubeYouTubeStart of suggested clipEnd of suggested clipOnce you have the line in the hole use hemostat forceps or needle nose pliers to reach into the tankMoreOnce you have the line in the hole use hemostat forceps or needle nose pliers to reach into the tank. And grab the fuel line then pull the line through the fuel tank filler opening.
How do you replace the throttle cable on a Poulan Pro chainsaw?
0:191:43Poulan 3818 Chainsaw Throttle Linkage Removal, Installation ...YouTubeStart of suggested clipEnd of suggested clipSo what you need to do is grab the linkage insert it in this hole like. This. Now you need to pressMoreSo what you need to do is grab the linkage insert it in this hole like. This. Now you need to press the throttle trigger. And what you need to do as well is push on the linkage.
How do you connect a primer bulb to a fuel line?
4:136:42How to tell where to correctly connect what fuel line on a weed eater ...YouTubeStart of suggested clipEnd of suggested clipSo whenever you connect the fuel line to this port it should be inserted in the gas tank. About anMoreSo whenever you connect the fuel line to this port it should be inserted in the gas tank. About an inch down into the gas tank. Then. This other port.
How do you adjust the carburetor on a Poulan Pro 42cc chainsaw?
2:237:01Carb Adjust on Poulon Pro 42cc Chainsaw - YouTubeYouTubeStart of suggested clipEnd of suggested clipIn a little too high. Turn that low screw out it'll stop the chain from spinning and get it idlingMoreIn a little too high. Turn that low screw out it'll stop the chain from spinning and get it idling just right okay. Now if you look right here. Here's your low and your high screws to adjust the carb.
How to change fuel line on Poulan Farmhand chainsaw?
How to change the fuel line in Poulan farmhand chainsaw? When you have completed this step, you will want to add the carburetor. Again, you can connect this by hand or by attaching it to the chain with the help of carburetor clips. When you have added the carburetor to make sure to attach the fuel line to the carburetor securely.
How to add fuel to Poulan chainsaw?
The first step is to add the fuel filter to your chainsaw. You can connect this to the chain, or it can be removed and connected by hand. It is important to note that in some models you will need to remove the spark plug before adding this. Next, connect the electric igniter to the chain and slowly but carefully add the fuel to the spark plug. Be sure to use a fuel filter that is appropriate for the model of the Poulan chainsaw you have.
How to tell if a Poulan chainsaw has a carburetor?
If you have an older Poulan chainsaw, it is likely that the carburetor is fed through a different fuel line than the electrical one. This is easily identified on older Poulan chainsaw models by looking at the two small holes near the rear of the carburetor.
What happens if you don't add fuel to a Poulan chainsaw?
If you don’t do this, the fuel filter can get backed up with the carburetor and clog the fuel line. Where does the little check valve go on a Poulan chainsaw fuel line?
How does Poulan work?
In order to properly use this Poulan chainsaw fuel line diagram, you should first know what a Poulan weed eater is. A Poulan weed eater is a machine that separates waste gas from fuel during the process of cutting firewood. The chain is also known as a Poulan chain and is used to transfer the fuel to a special mixing chamber where it can be warmed up. Once heated, it is then passed through a small pipe called a siphon tube, which is connected to a large fuel tank. This Poulan chainsaw fuel line diagram shows how this machine works.
What is Poulan Pro fuel line?
But what do they mean by Poulan pro chainsaw fuel line diagram? Basically, it refers to a Poulan chainsaw fuel line, which is crucial in ensuring that you get your machines working at top-notch.
Is it safe to replace a Poulan chainsaw fuel line?
Poulan chainsaw fuel line diagrams can help you understand your Poulan chainsaw fuel line replacement better. It is always better to be safe than sorry, especially when it comes to the fuel source of your chainsaw. Most manufacturers of these machines usually include a Poulan chainsaw fuel line in their product.
How to remove fuel line from carburetor?
Loosen the screws that hold the carburetor in place to remove it so you can access the fuel line that runs under it and extends into the fuel tank. Remove the fuel line. Pop the fuel filter off and attach the new filter to the end of the tubing.
How to clean up gasoline spills?
Keep paper towels on hand to wipe up any spilled gasoline.
How to remove carburetor from fuel tank?
Loosen the screws that hold the carburetor in place to remove it so you can access the fuel line that runs under it and extends into the fuel tank. Remove the fuel line. Pop the fuel filter off and attach the new filter to the end of the tubing. Drop the fuel filter and tubing into the fuel tank, and attach the other end to the carburetor. Run the tubing under the carburetor and reattach it by replacing the screws that you removed.
How to replace primer bulb in fuel tank?
Remove the thicker tube that connects the primer bulb to the fuel tank by pulling it off with your fingers. Hold it against the new tubing of the same diameter and cut a piece of the new tube to the same length. Replace the old tubing with the new tubing by attaching it to the primer bulb and inserting it into the fuel tank.
How to prevent accidental ignition of chainsaw?
Remove the spark plug wire from the spark plug to prevent accidental ignition of the chainsaw during the fuel line replacement. Empty the fuel from the gas tank into a gas can, and store it away from where you're working for replacement after the repair.
Can you replace gas lines on Poulan chainsaw?
Even if you're not particularly handy when it comes to repairs, replacing cracked or damaged gas lines on ...
What is the fuel supply hose on a Poulan chain saw?
The fuel supply hoses on Poulan chain saws carry fuel from the fuel tank to the purge bulb and carburetor. The purge bulb primes the carburetor for easier starting by injecting fuel into the carburetor. The return fuel hose returns the unused purge bulb fuel to the fuel tank.
Where is the starter housing on a chain saw?
Unscrew the retaining screws and lift the starter housing from the engine chassis on the chain saw's left side from the operator's position.
How to remove purge bulb from engine?
Unscrew the purge bulb retaining screws from the engine chassis. Pull the purge bulb outward from the chassis.
How to clean a carburetor with a filter?
1. Drain the fuel tank. Pull the carburetor fuel supply hose and filter from the tank. Pull the fuel filter housing nipple from the carburetor fuel supply hose end.
What is the return fuel hose?
The return fuel hose returns the unused purge bulb fuel to the fuel tank. These flexible fuel hoses harden and become brittle with exposure to fuel, oil and engine heat, and should be replaced to prevent fuel spillage or flash fire.
