You should be able to lift the door switch up from the dryer frame. Unplug the old, broken switch and plug in the new switch. Insert the new switch into the frame from the top of the dryer. Replace the two screws that hold the switch in place. Close the top of the dryer. It should snap into place.
- Unplug your Kenmore dryer from the wall outlet. ...
- Insert a putty knife under the top right of the cabinet. ...
- Lift the top of the cabinet to expose the door switch wiring harness along the front of the cabinet. ...
- Open the door to the dryer.
How to repair Kenmore dryer 80 series in 5 minutes?
Kenmore Dryer Repair. Search Help by Model. Your towels are wet, but your Kenmore dryer won't start. Or, perhaps the dryer started, but you can tell it's not spinning or heating, which means no fluffy towels for you. Before you pick up the phone and call a repair professional, take a look at our troubleshooting guide. Repair Clinic has ...
How to replace door switch on Kenmore dryer?
How to Wire a Dryer Door Switch
- Flip the dryer breaker switch to the "off" position.
- Open the dryer door and locate the dryer door switch. It will be on the inside lip where the door meets the dryer.
- Determine how the door switch is attached. ...
- Hold the replacement switch next to the switch that is to be replaced. ...
Where is the control panel 80 series dryer?
These are some common places to find the model number:
- the back of the control panel
- the upper-left-hand corner of the back
- the lower left-hand corner of the front
- any stickers on the lid or inside corners
- along the lower side panels
How do you replace a dryer door switch?
Replace the old switch with a new one. If the old switch just popped out of place, simply pop it back in. If you've had to open you dryer's cabinet in order to access and remove the door switch, reassemble it now. Run your dryer through a cycle to make sure it is working properly. For more information about dryer door switches: How to test a ...
How do you change a dryer switch on a Kenmore dryer?
0:261:33How to Replace a Kenmore Electric Dryer Push-to-Start Switch - YouTubeYouTubeStart of suggested clipEnd of suggested clipFor safety and to avoid damage to the new switch the wires must be properly connected. Position theMoreFor safety and to avoid damage to the new switch the wires must be properly connected. Position the panel on the back of the console. Line up the mounting screw holes insert. The mounting screws.
How do I remove a Kenmore door switch?
2:5910:30Kenmore Whirlpool Dryer door switch replacement - YouTubeYouTubeStart of suggested clipEnd of suggested clipSimply popping it out two screws on the bottom Phillips. Head holding the switch from the top. SoMoreSimply popping it out two screws on the bottom Phillips. Head holding the switch from the top. So you.
Why won't my Kenmore dryer door close?
The door has a matching, spring-loaded part called a catch. The catch is typically made of plastic and can wear out or break through repeated use. If the catch breaks, the door will not stay closed. Luckily, the catch can be replaced with just a few hand tools.
How do you remove a dryer door switch?
0:261:30How to Replace a Whirlpool Electric Dryer Door Switch - YouTubeYouTubeStart of suggested clipEnd of suggested clipUse a slot screwdriver to release the locking tab on the wire harness plug for the door switchMoreUse a slot screwdriver to release the locking tab on the wire harness plug for the door switch remove the mounting screws from the existing door switch. Pull the door switch out of the dryer.
How do I know if my dryer door switch is bad?
As a safety feature, the dryer will not work with an open door. When the switch is broken, it is unable to tell the control panel the door is shut, so the dryer will not turn on. The only way to tell if the switch is faulty is to take it out of the dryer and test it with a multimeter.
How do you remove the door switch on a Kenmore Elite dryer?
0:392:22Dryer Won't Start? Whirlpool/Kenmore Dryer Repair #3406107 - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou're now ready to replace the door switch detach the door switch wire connector remove the twoMoreYou're now ready to replace the door switch detach the door switch wire connector remove the two mounting screws at the door opening. And pull out the old switch.
How do you fix a dryer door that won't close?
0:191:28Whirlpool/Kenmore Electric Dryer Door Catch & Strike #279570YouTubeStart of suggested clipEnd of suggested clipIf still intact use pliers to squeeze the old door catch springs and push or slide the catches outMoreIf still intact use pliers to squeeze the old door catch springs and push or slide the catches out of the door panel depending on your model you can also use the pliers to pull out the old strike.
What do you do when your dryer door won't close?
If the problem is a bent hinge, the fix may be as simple as lifting the door into place so that the latch will catch. Tightening the latch screws may also repair a drooping door. If your door pops open during drying, or if your problem is due to a broken latch assembly, a more involved solution is necessary.
How do you fix a dryer that won't stay closed?
Replace the dryer door catch If the door won't latch closed and the strike is intact, replace the catch. If the door catch holds the door closed to start the cycle but can't continue to hold the door shut during the cycle to keep the dryer running, replace the door catch.
How do I test a Kenmore dryer door switch?
0:201:33Dryer Not Starting - How to Test the Door Switch - YouTubeYouTubeStart of suggested clipEnd of suggested clipGo to normally open so when the dryer doors. Open the motor is not going to be able to get power butMoreGo to normally open so when the dryer doors. Open the motor is not going to be able to get power but when you close the door.
How much does it cost to replace a dryer door switch?
Cost to Replace a Dryer Door Switch Replacing a door switch averages $50 to $150. The door switch is a small and cheap component, but it is very important because it detects when the door is closed or open to prevent the dryer from running with an open door.
How do you replace a dryer door latch?
0:142:05Dryer Repair- Replacing the Door Latch Kit (Frigidaire Part ... - YouTubeYouTubeStart of suggested clipEnd of suggested clipI'll take a flat blade screwdriver spoon from the side and depress the metal clamp. And simplyMoreI'll take a flat blade screwdriver spoon from the side and depress the metal clamp. And simply discard the old one. New one line it up make sure that the slot is vertical on it snap it into place.
How do I replace a dryer switch?
Reach inside the dryer cabinet, and pull out the old switch. Insert the new switch into the opening. Use the screws you removed from the original switch to secure the replacement switch.
How to release the top of a cabinet?
Insert a putty knife under the top right of the cabinet. Pull up on the putty knife to release the right side of the cabinet top from the cabinet body. Repeat this step to release the left side of the cabinet top.
How to test if dryer door switch is faulty?
If the door switch fails, the dryer won't start when the door is closed. To quickly test the door switch, open the dryer door and press the door switch lever. If the dryer drum light stays on, the door switch is faulty. Replace the door switch with the manufacturer-approved dryer part.
What to do if dryer is gas?
If it's a gas dryer, turn on the gas supply to the dryer. Warning: Undertaking repairs to appliances can be hazardous. Use the proper tools and safety equipment noted in the guide and follow all instructions.
Why won't my dryer light come on when I open the door?
If the light will not come on when you open the dryer door, it could be the light is burned out. If, however, the dryer will not stop when you open the door and the light will not come on, it is probably a broken door switch. Ask Question.
How to lift up a dryer?
Take a flat headed screwdriver (or similar device) and insert it between the top and the body of the dryer around 3-6 inches away from the edge. Gently separate the top from the body (this may take a little force). Do the same on the other side. The top should lift up.
Introduction
Electric clothing-washing machines have sensor switches about doors. A switch is a moving mechanical part. In Kenmore 80, this switch can wear-out, or its plastic screw bosses can break. Workspace: have room in front of your washing machine, enough space such that it could tip over forward so its front is on floor, in front of its present position.
Step 1 open console
Control panel console is fastened with two screws. Remove screws, pull bottom end of control panel forward (towards you), swing it upward, rest it in flipped position.
Step 2 unplug switch
Press on tab to release clip/latch. Grip connector, not wires, and pull it off of fixed connector.
Step 3 open case
Use prise tool to remove two case clips. Pull top of case towards you, rock case (almost whole cabinet: case top, front, left & right) on its bottom front edge as axis, lower front of case until it rests on floor.
Step 4 remove wiring
Case grounding wire is fastened on with one screw, 5/16 (five sixteenths) inch hexagon head. Unhook wires from the guide hooks.
Step 5 remove switch
To reassemble your device, follow these instructions in reverse order.
What happens when you bypass the lid switch on a Kenmore washer?
Warning. When bypassing the lid switch, touch only the insulated portion of the jumper wire with your fingers. The lid switch on your Kenmore washer completes the electrical circuit when the lid is closed. When your washer will not operate, you need to troubleshoot the lid switch before investigating other possible causes.
How to test a lid switch?
The best way to test the lid switch is with a volt-ohm meter. If you do not have a volt-ohm meter, you can bypass the lid switch using a jumper wire to simulate the connection to the washer wiring harness. Advertisement.
Where is the lid switch wire harness?
Locate the lid switch wiring harness on the rear of the top panel. Grasp the wiring harness connector with your fingers and pull it away from the lid switch plug.