How do you replace a Kohler shower handle?
- Turn off the water (and cover the drain!) If you're working on the sink, you can usually find the valve and handle right below it or within the the cabinet ...
- Remove faucet handles or cover plates.
- Remove locking nut.
- Remove faucet cartridge.
- Replace and retrace.
Full Answer
How do you remove a Kohler shower valve?
Trim with Setscrews
- Using a 3/32” hex wrench, loosen the two setscrews. ...
- Using a Phillips screwdriver, unthread the screw and remove the adaptor from the valve stem.
- Unthread the collar. ...
- Using a Phillips screwdriver, unthread the two screws and remove the seal plate.
- If applicable, use a flat-blade screwdriver to remove the pin from the adaptor. ...
How to remove a sink stopper Kohler?
Removing the Stopper The ball rod holds the stopper in the drain. To reach the stopper, the ball rod needs to be removed first. The ball rod is inserted into the side of the drain and attached with a nut. To remove, unthread the rod nut, pull the ball rod out, and remove the stopper from the drain.
How to clean Kohler cleancoat shower doors?
Things You'll Need
- Squeegee
- Soft cloth
- Spray cleaner
- Non-abrasive sponge or scrubber
How to repair a leaking Kohler shower faucet?
- Water Flows From Showerhead & Tub Spout Simultaneously. Please review the "Important Information" notes of the installation instructions. ...
- No Water Output. Rite-Temp valves feature a pressure-balancing unit (PBU). ...
- Hot Water First. ...
- Water Temperature Fluctuations. ...
- Delayed Flow. ...
- Leak After New Service Kit Installed. ...
- Springs Fell Out of Cap Assembly. ...
How do you remove a Kohler shower handle?
Firmly grasp the handle. Turn the bonnet counterclockwise and remove the handle and bonnet from the valve stem. Using a Phillips screwdriver, unthread the two screws and remove the handle sleeve, shroud, and faceplate. If applicable, use a flat-blade screwdriver to remove the pin from the adaptor.
How do you remove a Kohler handle?
Hold the handle with one hand. Using your other hand, turn the skirt, the decorative flared piece below the handle, counterclockwise. A strap wrench may also be used, taking care to protect all finish surfaces. Remove any remaining components to expose the valve.
How do you take apart a Kohler Single handle shower faucet?
0:005:22How To Replace A Kohler Shower Faucet Cartridge - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnything from falling down the drain. Now. Once you get the handle of the trim plate off now you'reMoreAnything from falling down the drain. Now. Once you get the handle of the trim plate off now you're going to find a couple of screws that's holding the bracket that holds the handle on.
How do you install a Kohler shower handle?
5:136:41Next Gen Rite-Temp Shower Valve - KOHLER - YouTubeYouTubeStart of suggested clipEnd of suggested clipHold the face plate. So it doesn't twist and turn the handle collar clockwise to tighten it up andMoreHold the face plate. So it doesn't twist and turn the handle collar clockwise to tighten it up and you're done the knurl right temp pressure balancing valve is the next generation in shower valving.
How do you take off a shower handle?
You can usually pop this off with a flat head screwdriver. Place the screwdriver head between the cap and the faucet and tap it gently with a hammer, and the cap should pop off. If you have a faucet with a lever-style handle, look for a set screw underneath the lever. You'll need a 1/8-inch Allen wrench to remove it.
How do you remove a Kohler faucet handle without screws?
0:545:17how to remove a tap with no screw with Inspire DIY Kent ThomasYouTubeStart of suggested clipEnd of suggested clipKey if they don't have a grub screw around the back then they'll be the type that unscrews.MoreKey if they don't have a grub screw around the back then they'll be the type that unscrews. Sometimes you can just twist them off sometimes they're really tight.
How do you remove a Kohler bathroom faucet handle?
0:271:47Replace Two Handle Ultra Glide Valves - Faucet - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe valve body and untwist the handle. Once the valve body is out of the faucet remove the handleMoreThe valve body and untwist the handle. Once the valve body is out of the faucet remove the handle from the existing. Body attach the hardware to the valve body including the hose.
How do you remove a Kohler single handle bathroom faucet?
Single-Handle Bathroom Sink Faucets - Handle RemovalUsing a bladed screwdriver, gently pry off the plug button under the handle, taking care to protect all finished surfaces.Using a 1/8" hex wrench, loosen the setscrew securing the handle to the valve stem.Lift off the handle.Unthread the bonnet to expose the valve.
How do you remove a shower faucet that has no screws?
Feel under the spout near the wall for a hole. The set screw is hidden inside the hole. ... Put a pipe wrench on the middle of the spout with the handle pointing to the left. ... Turn the bathtub faucet spout counterclockwise with the pipe wrench until you can twist the spout by hand.
How do you install a single handle shower faucet?
7:359:50Installing A One-Handle Posi-Temp® Shower Valve: IPS to IPS - YouTubeYouTubeStart of suggested clipEnd of suggested clipApply caulk around the base of the tub spout pipe to prevent leaking behind the wall. Then screw onMoreApply caulk around the base of the tub spout pipe to prevent leaking behind the wall. Then screw on the tub. Spout. Now slide the stop tube onto the valve and attach the discussion with two screws.
How do you replace a shower faucet?
0:0212:12How To Install a Shower Faucet | The Home Depot - YouTubeYouTubeStart of suggested clipEnd of suggested clipBefore you can replace the fixtures in your shower. You'll first need to start by turning off theMoreBefore you can replace the fixtures in your shower. You'll first need to start by turning off the water supply unless you happen to have a separate cutoff valve installed in the bathroom.
How do you remove a bathtub handle?
How to Remove Bathtub HandlesBegin by using a flat-head screwdriver to pry off the handle's plastic cover (also called the plastic insert or index).Unscrew the handle screw with a flathead or Phillips-head screwdriver as needed.Wiggle the handle and pull it off.More items...
How do you remove a shower handle?
Remove your shower handle by first removing the diverter button. Once you remove the diverter button, continue to remove the trim. Once you remove...
How do you remove a shower handle without a screw?
Struggling to find the screws holding your shower handle in place? They may not exist. Use a flat screwdriver to remove the handle.
How do you remove a double handle Kohler shower handle?
To remove a double handle Kohler shower handle, you will remove each handle separately. The diverter will also be separate from the two shower hand...
How to remove a valve sleeve?
Then, remove the valve trim. Find the setscrew (s) on the diverter button. Loosen the setscrew (s) with the 1/16-inch hex wrench. Remove the diverter button.
How to remove a retainer from a valve stem?
If applicable, remove the pivot ring. Then, remove the faceplate. Using a Phillips screwdriver, unthread the screws to remove the retainer. If you don’t see any screws, remove the retainer.
Can you remove a Kohler shower handle?
However, you will be able to remove your Kohler shower handle in no time using the images and three steps below.
How to remove a valve retainer?
Using a Phillips screwdriver, unscrew the two screws and remove the retainer. If no screws are present, unscrew and remove the retainer. Firmly grasp the handle. Turn the bonnet counterclockwise and remove the handle and bonnet from the valve stem.
How to remove a pin from a valve?
Using a Phillips screwdriver, unscrew the two screws from the face plate. Remove the washer and the face plate. If applicable, use a flat-blade screwdriver to remove the pin from the adapter. Unscrew and remove the adapter from the valve.
How to unscrew a K-87448?
You may need a special tool (K-87448) to unscrew the collar. Remove the face plate and the collar. Using a Phillips screwdriver, unscrew the two screws and remove the seal plate. If applicable, use a flat-blade screwdriver to remove the pin from the adapter.
Overview
This document is intended to help identify and remove the trim from your KOHLER single-control bath or shower valve. Identify your valve trim by referring to the thumbnails, then follow the instructions listed below the image to remove the trim.
Identify Your Shower Valve
Once you have removed your valve trim, the documents listed below are available to help you identify your shower valve.
Remove the Diverter Button
If your trim has a diverter button, remove the button before attempting to remove the valve trim. If your trim does not have a diverter button, move on to identifying your valve trim.
Trim with Exposed Screws
Using a Phillips screwdriver, unthread the screw and remove the handle, bonnet and sleeve from the valve stem.
Trim with Plug Buttons
Using a flat-blade screwdriver, gently pry the plug button from the front of the valve trim.
Trim with Setscrews
Using a 3/32” hex wrench, loosen the two setscrews. You may need to rotate the sleeve to access both setscrews. Slide the handle and sleeve off the valve.
Trim with Threaded Bonnets
Firmly grasp the handle. Turn the bonnet counterclockwise and remove the handle and bonnet from the valve stem.

Step 1 – Getting Started
Step 2 – Remove Diverter Button
- Once you have all of your tools in place, remove the diverter button. Not all handle types will have a diverter button. Skip to step three, if applicable.
Step 3 – Remove Trim
- Removing Trim with Exposed Screws
Use a Phillips screwdriver to unscrew the screw from the valve stem, allowing you to remove the handle, bonnet, and sleeve. Then, use the same screwdriver to unscrew the two screws on the faceplate. Remove the escutcheon and the faceplate. If applicable, remove the pin from the ada… - Removing Trim with a Plug Button
Using a flat-blade screwdriver, gently pry the plug button from the valve trim. Using a Phillips screwdriver, unscrew the screws and remove the handle and adaptor from the valve stem. You may need to turn the cover counterclockwise. With your Phillips screwdriver, unscrew the facepl…