How to Remove an Idler Pulley
- Open the hood of the vehicle and locate the drive belt. ...
- Remove the drive belt by relieving the tension on the belt tensioner (if applicable). ...
- Do not remove the entire belt unless you're replacing the belt. ...
- Locate the idler pulley in the pulley system.
- Use a ratchet and a socket or a hand wrench to turn the bolt head located in the center of the idler pulley counterclockwise.
Full Answer
How much does it cost to replace an idler pulley?
The total price to replace the idler pulley typically ranges between $80 and $200, with the parts ranging between $40 and $90, and the total labor cost averaged between $40 and $110.
How long can you drive with a bad idler pulley?
So, how long can you drive with a bad idler pulley? The safety recommendation is not to drive the car at all and take it to a mechanic immediately. You should be concerned if the vehicle makes squeaking or rattling noises. The car can still run for months or break after a few days.
Can you bypass idler pulley?
You can bypass both the AC compressor and the middle serpentine idler pulley with a 6PK1790. The middle pulley is bypassed by running the belt straight line from the upper rear serpentine idler straight to the power steering pulley, then over the water pump (the smooth pulley powered by the back side of the belt) and down to the engine drive pulley (harmonic balancer), bypassing the AC compressor) This works fine.
Can You lubricate idler pulley?
You can go to the extent of soaking the pulley in gasoline to dissolve everything, let it dry and repack with grease. I simply cleaned old grease off where I can (Q-tip); then pack new grease using my finger. Then gently drive the seal back in. I used mostly 30-mm socket because it fits perfectly.
How to turn a bolt head on a pulley?
What is the main pulley on a car?
What happens if you don't have a belt tensioner?
What direction should a belt tensioner be turned?
Can you remove the belt from an idler?
See more
About this website
How do I remove idler pulley hardware?
1:344:55Idler Pulley, How to replace (EASY and CHEAP) - YouTubeYouTubeStart of suggested clipEnd of suggested clipNow just remove the tool. You could either use a 5/8 socket or a 15 millimeter socket with the beltMoreNow just remove the tool. You could either use a 5/8 socket or a 15 millimeter socket with the belt tension loose we'll start taking the pulley. Off.
How do I remove the idler pulley bolt?
0:513:40How to Remove Idler Pulley - YouTubeYouTubeStart of suggested clipEnd of suggested clipOkay when you loosen up the idler pulley. Take your socket sucker wrench and socket out of thereMoreOkay when you loosen up the idler pulley. Take your socket sucker wrench and socket out of there because it'll get stuck in there you'll be loosening loose and loosening and then all of a sudden.
Are idler pulley bolts reverse threaded?
If it's just an idler pulley it's standard. If it's a tensioner pulley it may be reverse thread depending on the way you need to move the pulley to unload it.
How long does it take to change idler pulley?
If you are doing the job at home, give yourself about four hours to change all the parts. You will need the following tools and parts: Replacement idler pulley.
How do you remove a pulley from a car?
1:213:03How to Remove a Crankshaft Pulley in Your Car - YouTubeYouTubeStart of suggested clipEnd of suggested clipThey get the puller assembly. Put it over and get one nut bolt and screw it into the little hole.MoreThey get the puller assembly. Put it over and get one nut bolt and screw it into the little hole. Then screw another bolt and washer until the hole on the opposite side you have both on snug.
Are idler pulley and tensioner pulley the same?
The primary distinction between tensioners and idler pulleys is the presence of an adjustable bolt. Tensioners are positioned on the bolt through mounting. Idler pulleys are not mounted to an adjustable bolt.
Is a belt tensioner bolt reverse thread?
The bolt for the tensioner pulley is left hand thread(reverse) The bolts for the tensioner assembly are regular threads.
What does the idler pulley do?
The idler pulley is a common part that's found on the majority of the vehicles on the road. Its primary function is to provide tension and guide the engine drive belt. These belts wrap around the various parts of the engine such as the power steering pump, alternator, water pump etc...
Can you drive without an idler pulley?
The idler pulleys may not be the most well-known car components or the most common cause of good old driver headaches. But, they are essential for seamless engine performance, and if one of them fails the vehicle will simply stop working.
What does an idler pulley sound like when it's going out?
Idler pulley slippage is likely to follow after it becomes worn out enough. This will cause the pulley to bind and then rub against the engine belt. As a result, there will be squealing noises coming from the engine area that will only get worse until the pulley is replaced.
How do you know if you have a bad idler pulley?
1:104:44HOW TO DIAGNOSE BAD IDLER PULLEY BEARING - YouTubeYouTubeStart of suggested clipEnd of suggested clipBest famous one is kind of like an alternator noise where you can hear it sounds like you have aMoreBest famous one is kind of like an alternator noise where you can hear it sounds like you have a supercharger. And if it's dependent on engine rpm. And you can hear the pitch.
IDLER PULLEY REMOVAL | Lawn Mower Forum
Hellow fellow Hustlers.... I am restoring my deck on my Hustler 54 SD Raptor, I want to remove the idler pulley. I thought it would be a simple remove the nut and pull the pulley up but mine seem to be pressed on. Is this correct? Any advise on how to remove the 2 idler pulleys would be a great...
How to Remove a Vehicle's Idler Pulley | DoItYourself.com
A vehicle’s idler pulley is the one responsible for the routing of the drive-belt along the different engine accessories, such as the air conditioner, alternator and power steering. If this pulley is damaged, it may cause the belt riding on it to get damaged and also affect other engine accessory functions. It should be replaced quickly in order for your car to run at its optimum level.
How to Fix the Idler Spring on a Zero-Turn Mower - SF Gate
How to Fix the Idler Spring on a Zero-Turn Mower. An idler pulley, idler arm and idler arm spring put tension on the mower deck drive belt of a zero-turn riding lawnmower. That drive belt spins ...
How to replace idler pulley?
Socket set and ratchet. Torque wrench. Step 1: Disconnect the battery. Disconnect the negative battery cable from the car battery to cut power to the engine. Set the cable aside where it cannot make contact with anything metal. Step 2: Remove the drive belt. To remove the drive belt, first release the tension to the belt. ...
What is an idler pulley?
Idler pulleys are a newer style of tensioner and guide for your vehicle’s drive belt. They help to maintain control and tension on the belt as it rotates at high speeds. Failure in this pulley can result in a loose or dropped drive belt, noises from failed bearings, and or a damaged drive belt.
What happens when idler pulley is attached to alternator?
If your idler pulley attaches to the alternator, you will have to remove the bolt attaching the pulley to the alternator and push the entire alternator down to relieve the tension on the belt.
Raise the top panel
Pull the lint screen out of the housing in the top panel of the dryer.
Remove the front panel
Use a slot screwdriver to release the locking tab on the wire harness plug for the door switch. Disconnect the wire harness.
Remove the idler pulley
Take a digital picture of the configuration of the drive belt on the idler pulley and the motor pulley so you can install it correctly.
Install the new idler pulley
Install the idler pulley in the bracket at the base of the dryer and thread the drive belt through the new idler pulley.
Restore power to the dryer
Plug the dryer into the wall outlet. If it's a gas dryer, turn on the gas supply to the dryer.
How to replace a dryer drum support roller
If your dryer thumps or squeals, replace the drum support roller to restore quiet to your home.
How to replace a dryer idler pulley
The idler pulley exerts pressure keeps the drive belt tight so it can rotate the drum. A worn idler pulley squeals or squeaks when the dryer is running. Follow these instructions to replace it.
How to turn a bolt head on a pulley?
Use a ratchet and a socket or a hand wrench to turn the bolt head located in the center of the idler pulley counterclockwise. Remove the bolt and then remove the pulley.
What is the main pulley on a car?
by Jody L. Campbell. Different engines use different drive belts routed along a pulley system to power the engine components. The main pulley is the crankshaft pulley ; most often the lowest pulley in the center.
What happens if you don't have a belt tensioner?
If a belt tensioner is not present, most likely the tension on the belt is created by the position of the alternator in a slotted bracket.
What direction should a belt tensioner be turned?
In most cases, a wrench placed on the bolt at the center of the pulley or a ratchet ( with no socket) inserted into a square drive located on the base of the tensioner pulley will be turned clockwise.
Can you remove the belt from an idler?
Do not remove the entire belt unless you're replacing the belt. In most cases , you can let the belt dangle from the existing pulleys as long as it is not in the way of accessing the idler pulley.